Skip to main content
v2026.11,986 entries · CC-BY 4.0

12 Principles of Green Chemistry: Original Wording and EPA Plain-Language Version

The 12 principles of green chemistry: original Anastas and Warner wording, the EPA’s plain-language version, and how green chemistry differs from cleanup.

Written and maintained by CASRAI Editorial Board

Published

On this page

The 12 principles of green chemistry are a list of design guidelines, published by Paul Anastas and John Warner in 1998, for making chemical products and processes that reduce or eliminate the use and generation of hazardous substances. They run from preventing waste (principle 1) to choosing substances and forms that minimize the chance of releases, explosions and fires (principle 12). This page sets the original wording beside the US EPA’s plain-language version and groups the principles by the decision they inform at the bench.

Short answer

Green chemistry is, in the words of the Yale Center for Green Chemistry and Green Engineering, “the design of chemical products and processes that reduce or eliminate the use and generation of hazardous substances.” The 12 principles are the checklist usually used to apply that definition: prevent waste, maximize atom economy, design less hazardous syntheses and safer chemicals, use safer solvents, save energy, use renewable feedstocks, avoid derivatives, prefer catalysis, design for degradation, monitor in real time, and choose inherently safer chemistry. The data table below the article lists all 12 with the EPA phrasing and an editorial grouping.

Definition and scope

Both of the sources this page relies on use the same definition. The EPA adds two points about scope. First, green chemistry applies across the life cycle of a chemical product, including its design, manufacture, use and ultimate disposal. Second, it is described as a philosophy that applies to all areas of chemistry, not a single discipline of chemistry, and it works by preventing pollution at the molecular level, which the EPA describes as source reduction.

The principles are attributed to Anastas and Warner (Green Chemistry: Theory and Practice, Oxford University Press, New York, 1998, p. 30), the citation Yale gives alongside the verbatim list. They are written as design statements about substances, syntheses and processes. They are not exposure limits, regulatory thresholds or a certification scheme, and neither source treats them as one.

The 12 principles in the original wording

The list below reproduces the wording published by the Yale Center for Green Chemistry and Green Engineering (read 12 November 2026), which credits Anastas and Warner.

  1. Prevention. “It is better to prevent waste than to treat or clean up waste after it has been created.”
  2. Atom Economy. “Synthetic methods should be designed to maximize the incorporation of all materials used in the process into the final product.”
  3. Less Hazardous Chemical Syntheses. “Wherever practicable, synthetic methods should be designed to use and generate substances that possess little or no toxicity to human health and the environment.”
  4. Designing Safer Chemicals. “Chemical products should be designed to effect their desired function while minimizing their toxicity.”
  5. Safer Solvents and Auxiliaries. “The use of auxiliary substances (e.g., solvents, separation agents, etc.) should be made unnecessary wherever possible and innocuous when used.”
  6. Design for Energy Efficiency. “Energy requirements of chemical processes should be recognized for their environmental and economic impacts and should be minimized. If possible, synthetic methods should be conducted at ambient temperature and pressure.”
  7. Use of Renewable Feedstocks. “A raw material or feedstock should be renewable rather than depleting whenever technically and economically practicable.”
  8. Reduce Derivatives. “Unnecessary derivatization (use of blocking groups, protection/ deprotection, temporary modification of physical/chemical processes) should be minimized or avoided if possible, because such steps require additional reagents and can generate waste.”
  9. Catalysis. “Catalytic reagents (as selective as possible) are superior to stoichiometric reagents.”
  10. Design for Degradation. “Chemical products should be designed so that at the end of their function they break down into innocuous degradation products and do not persist in the environment.”
  11. Real-time analysis for Pollution Prevention. “Analytical methodologies need to be further developed to allow for real-time, in-process monitoring and control prior to the formation of hazardous substances.”
  12. Inherently Safer Chemistry for Accident Prevention. “Substances and the form of a substance used in a chemical process should be chosen to minimize the potential for chemical accidents, including releases, explosions, and fires.”

How the EPA restates them

The EPA’s “Basics of Green Chemistry” page (read 12 November 2026) turns each principle into an imperative with a short gloss. The data table below the article places the two versions side by side. Reading them together shows where the EPA version adds something the original sentence does not state in so many words:

  • Principle 5. The original asks that auxiliary substances be “made unnecessary wherever possible and innocuous when used.” The EPA puts the same priority order as an instruction: avoid solvents, separation agents or other auxiliary chemicals, and if you must use them, use safer ones. The EPA heading also adds “reaction conditions”.
  • Principle 7. The original only says renewable rather than depleting. The EPA adds that renewable feedstocks are often agricultural products or the wastes of other processes, while depletable ones are often fossil fuels (petroleum, natural gas or coal) or come from mining operations.
  • Principle 9. The original states that catalytic reagents are superior to stoichiometric reagents. The EPA explains why: catalysts are effective in small amounts and can carry out a single reaction many times, whereas stoichiometric reagents are used in excess and carry out a reaction only once.
  • Principle 6. The original asks that energy requirements be recognized for their environmental and economic impacts and minimized. The EPA’s version is reduced to running reactions at room temperature and pressure whenever possible, which is the original’s second sentence taken on its own.
  • Principle 12. The EPA spells out the physical forms (solid, liquid or gas) that the original calls “the form of a substance”.

Green chemistry versus cleanup

The EPA draws a firm line between green chemistry and remediation. Remediation treats waste streams (end-of-the-pipe treatment) or cleans up spills and other releases; it may separate hazardous chemicals from other materials and then treat or concentrate them for safe disposal. In the EPA’s words, “Most remediation activities do not involve green chemistry.” Remediation removes hazardous materials from the environment, while green chemistry keeps the hazardous materials from being generated in the first place.

The line is about the technology, not the setting. The EPA gives one example: a hazardous sorbent used to capture mercury from the air for safe disposal can be replaced by an effective but nonhazardous sorbent. Because the hazardous sorbent is then never manufactured, the remediation technology meets the definition of green chemistry. This is principle 1 (prevention) and principle 3 (less hazardous syntheses) applied to a cleanup material.

The same logic appears in US pollution policy. The EPA quotes the Pollution Prevention Act of 1990, in which Congress declared it to be the national policy of the United States that pollution should be prevented or reduced at the source whenever feasible. The page presents green chemistry as one way of achieving that source reduction. The first principle, prevention over treatment, is the chemistry-level statement of the same ordering.

Grouping the principles by decision

Neither source groups the principles. The grouping below is an editorial aid from CASRAI, not part of the original list or the EPA text, and each principle is placed according to what its own wording is about. It is repeated as a column in the data table.

Reaction design: principles 2, 3, 8 and 9

These concern how a synthesis is built. Atom economy asks that the process maximize incorporation of all materials into the final product. Less hazardous syntheses asks for substances with little or no toxicity to be used and generated. Reduce derivatives targets blocking groups, protection and deprotection and temporary modifications because they require additional reagents and can generate waste. Catalysis prefers catalytic over stoichiometric reagents. For a related catalysis topic on this site, see heterogeneous catalysis.

Materials and products: principles 4, 5, 7 and 10

These concern what goes in and what comes out. Designing safer chemicals concerns the product’s toxicity relative to its function. Safer solvents and auxiliaries concerns separation agents and solvents. Renewable feedstocks concerns starting materials. Design for degradation concerns what the product becomes after use: the original asks that it break down into innocuous degradation products and not persist in the environment.

Process and safety: principles 1, 6, 11 and 12

These concern how a process is run. Prevention frames waste as something avoided rather than treated. Energy efficiency asks that energy needs be recognized and minimized and, if possible, that syntheses run at ambient temperature and pressure. Real-time analysis calls for in-process monitoring and control before hazardous substances form. Inherently safer chemistry concerns the choice of substances and their form to minimize releases, explosions and fires.

Where it matters for labs

The sources are written for chemistry in general, so they do not prescribe laboratory procedures, and this page does not either. What they do support is a set of questions a research group can ask of a method, each tied to a named principle: Does the route need protecting groups (principle 8)? Is a solvent or separation agent needed at all, and if so is a safer one available (principle 5)? Could a catalytic step replace a stoichiometric reagent (principle 9)? Can the reaction run at ambient temperature and pressure (principle 6)? Can the process be monitored in real time to avoid byproducts (principle 11)?

For laboratory-wide practice such as audits, purchasing and waste streams rather than individual reactions, see sustainable lab practices, the 5R framework for lab sustainability and lab waste audit. For the certification programme, see My Green Lab. Hazardous operations in the lab still depend on engineering controls such as a fume hood; the principles aim to reduce the hazard at the source, not to replace those controls.

Common misunderstandings

It is not only about solvents

Solvents are one principle (5) of twelve. The list also covers syntheses, feedstocks, product design, energy, analysis and accident prevention, and the EPA says the approach spans the whole life cycle from design to disposal.

It is not the same as pollution cleanup

As set out above, the EPA separates the two. A cleanup technology counts as green chemistry only when it reduces or eliminates the hazardous chemicals used in the cleanup itself.

The principles are not a single score

The twelve statements are design guidelines, not a metric. Individual measures exist for particular principles. Sheldon’s review “The E factor 25 years on” (Green Chemistry, 2017, 19, 18–43, doi:10.1039/C6GC02157C) notes that the E factor reports actual waste while atom economy is a theoretical value calculated from molecular weights, and that mass-based metrics need to be supplemented by life cycle assessment. No single number summarizes all twelve.

Some wording is conditional

Several original statements carry qualifiers: “wherever practicable” (principle 3), “wherever possible” (principle 5), “if possible” (principle 6) and “whenever technically and economically practicable” (principle 7). They are goals to weigh in design, not absolute requirements.

The list dates from 1998 and is under discussion

A 2026 perspective in Green Chemistry by Lipshutz and Handa, “Modernizing the 12 principles of green chemistry: it’s time” (volume 28, pages 5606–5612, doi:10.1039/D5GC05289K), argues that the principles, developed about 30 years ago, should be revised. This page covers the established list as published by Yale and the EPA.

Frequently asked questions

What are the 12 principles of green chemistry?

They are twelve design guidelines attributed to Anastas and Warner (1998): prevention, atom economy, less hazardous chemical syntheses, designing safer chemicals, safer solvents and auxiliaries, design for energy efficiency, use of renewable feedstocks, reduce derivatives, catalysis, design for degradation, real-time analysis for pollution prevention, and inherently safer chemistry for accident prevention.

Who developed the 12 principles of green chemistry?

Yale’s Center for Green Chemistry and Green Engineering credits Paul T. Anastas and John C. Warner, Green Chemistry: Theory and Practice, Oxford University Press, New York, 1998, p. 30.

What is green chemistry in one sentence?

It is the design of chemical products and processes that reduce or eliminate the use and generation of hazardous substances.

Is green chemistry the same as environmental cleanup?

No. The EPA says remediation removes hazardous materials from the environment, whereas green chemistry keeps hazardous materials from being generated in the first place. A cleanup technology qualifies only if it reduces or eliminates hazardous chemicals used in the cleanup.

Why does the EPA list differ from the Yale list?

The EPA restates each principle as a short instruction with a gloss for a general audience, for example adding sources of renewable feedstocks. The Yale page reproduces the original Anastas and Warner sentences.

Have the 12 principles been updated?

A 2026 perspective in Green Chemistry (Lipshutz and Handa) argues that they should be revised. The list as published by Yale and the EPA is still the 1998 formulation.

Sources

  • Yale Center for Green Chemistry and Green Engineering, “Principles of Green Chemistry”, https://greenchemistry.yale.edu/node/26, read 12 November 2026.
  • US Environmental Protection Agency, “Basics of Green Chemistry”, https://www.epa.gov/greenchemistry/basics-green-chemistry, read 12 November 2026.
  • Anastas, P. T. and Warner, J. C. Green Chemistry: Theory and Practice. Oxford University Press, New York, 1998, p. 30 (as cited by Yale).
  • Sheldon, R. A. “The E factor 25 years on: the rise of green chemistry and sustainability”, Green Chemistry 2017, 19, 18–43, doi:10.1039/C6GC02157C (bibliographic reference).
  • Lipshutz, B. H. and Handa, S. “Modernizing the 12 principles of green chemistry: it’s time”, Green Chemistry 2026, 28, 5606–5612, doi:10.1039/D5GC05289K (bibliographic reference).

Data: The 12 principles of green chemistry: original names, EPA plain-language versions and editorial grouping

Cross-walk of the 12 principles of green chemistry. Principle names follow the Yale Center for Green Chemistry and Green Engineering list (Anastas and Warner, 1998); the heading and gloss columns are taken from the US EPA 'Basics of Green Chemistry' page (glosses lightly shortened); the grouping column is an editorial classification by CASRAI, not part of either source.

Period covered: 1998/2026.

The 12 principles of green chemistry: original names, EPA plain-language versions and editorial grouping
Principle numberOriginal name (Yale / Anastas and Warner)EPA plain-language headingEPA gloss (shortened)Editorial grouping (CASRAI)
1PreventionPrevent wasteLeave no waste to treat or clean up.Process and safety
2Atom EconomyMaximize atom economyWaste few or no atoms.Reaction design
3Less Hazardous Chemical SynthesesDesign less hazardous chemical synthesesUse and generate substances with little or no toxicity to either humans or the environment.Reaction design
4Designing Safer ChemicalsDesign safer chemicals and productsChemical products that are fully effective yet have little or no toxicity.Materials and products
5Safer Solvents and AuxiliariesUse safer solvents and reaction conditionsAvoid solvents, separation agents or other auxiliary chemicals; if you must use them, use safer ones.Materials and products
6Design for Energy EfficiencyIncrease energy efficiencyRun chemical reactions at room temperature and pressure whenever possible.Process and safety
7Use of Renewable FeedstocksUse renewable feedstocksRenewable rather than depletable starting materials; renewable sources are often agricultural products or the wastes of other processes.Materials and products
8Reduce DerivativesAvoid chemical derivativesAvoid blocking or protecting groups or any temporary modifications if possible; derivatives use additional reagents and generate waste.Reaction design
9CatalysisUse catalysts, not stoichiometric reagentsCatalysts are effective in small amounts and can carry out a single reaction many times.Reaction design
10Design for DegradationDesign chemicals and products to degrade after useBreak down to innocuous substances after use so that they do not accumulate in the environment.Materials and products
11Real-time analysis for Pollution PreventionAnalyze in real time to prevent pollutionIn-process, real-time monitoring and control during syntheses to minimize or eliminate byproducts.Process and safety
12Inherently Safer Chemistry for Accident PreventionMinimize the potential for accidentsDesign chemicals and their physical forms (solid, liquid, or gas) to minimize explosions, fires and releases to the environment.Process and safety

Sources

Compiled by CASRAI from the sources above. Free to reuse under CC BY 4.0 with attribution.

Follow CASRAI

Research-administration guidance, standards updates and independent tool reviews.

Ask CASRAI · full access

Ask about 12 Principles of Green Chemistry: Original Wording and EPA Plain-Language Version

Full access: large monthly usage, up to 10 source passages behind each answer, and MCP and API access for Claude Code, Codex and other CLIs. Cancel any time.

An AI assistant for research: funder rules, compliance, methods and publishing. It links the sources behind its answers and labels answers that come from a web search.

Answers draw on CASRAI's guides and dictionary plus the federal and funder documents we index: Federal Register, Grants.gov, Regulations.gov and UKRI.

Works on this site and inside Claude, Cursor and the AI tools you already use.

Everything CASRAI publishes — this page, the dictionary, the guides and the news — stays open to read, with no account and no card.

Referenced across the research world

University of Cambridge logoColumbia University logoCrossref logoUniversity of Edinburgh logoHarvard University logoUniversity of Oxford logoPrinceton University logoStanford School of Medicine logoUniversity College London logoORCID logoUniversity of Cambridge logoColumbia University logoCrossref logoUniversity of Edinburgh logoHarvard University logoUniversity of Oxford logoPrinceton University logoStanford School of Medicine logoUniversity College London logoORCID logo
  • University of Cambridge logo
  • Columbia University logo
  • Crossref logo
  • University of Edinburgh logo
  • Harvard University logo
  • University of Oxford logo
  • Princeton University logo
  • Stanford School of Medicine logo
  • University College London logo
  • ORCID logo

View CASRAI adoption →