Skip to main content
v2026.11,986 entries · CC-BY 4.0

14 CFR Part 23: Airworthiness Standards for Normal Category Airplanes

Guide to FAA 14 CFR Part 23 airworthiness standards: Amendment 23-64 rules, ASTM F3264 compliance, certification levels, and type certification steps.

Written and maintained by CASRAI Editorial Board

Published · Last updated

On this page

Title 14 of the Code of Federal Regulations (CFR) Part 23 contains the Federal Aviation Administration (FAA) airworthiness standards for normal category airplanes with a passenger seating configuration of 19 or fewer seats and a maximum certificated takeoff weight of 19,000 pounds or less. As described on the official page on 2026-11-13, Part 23 establishes the minimum safety, structural, flight handling, and powerplant installation requirements that aeronautical manufacturers, flight laboratories, and research institutions must demonstrate to achieve federal type certification.

What it is and who runs it

Part 23 is administered by the Federal Aviation Administration under the Department of Transportation (DOT), executed primarily through the FAA Aircraft Certification Service (AIR) and its regional branches. The regulation establishes airworthiness baselines for the design, construction, and testing of light, utility, acrobatic, and small commuter aircraft operated within United States civil airspace.

Historically, Part 23 relied on prescriptive technical mandates codified in 1964 from the Civil Air Regulations (CAR Part 3). These legacy standards prescribed specific engineering solutions and material dimensions. Following the statutory mandate of the Small Airplane Revitalization Act of 2013 (SARA, Public Law 113-53), the FAA promulgated Amendment 23-64 (81 FR 96572), effective August 30, 2017. Amendment 23-64 replaced over 400 prescriptive mandates with objective, performance-based safety requirements.

Under this modernized framework, Part 23 defines safety outcomes, while specific technical means of compliance are developed through industry consensus bodies, notably ASTM International Committee F44 on General Aviation Aircraft. This architecture allows aerospace developers to certify novel technologies—including electric propulsion, fly-by-wire flight controls, composite structures, and autonomous systems—without requiring burdensome regulatory exemptions. Part 23 is harmonized internationally with European Union Aviation Safety Agency (EASA) CS-23 Amendment 5, facilitating reciprocal type validation.

Eligibility (summary, with the official source)

As described on the official page on 2026-11-13 in 14 CFR § 23.2000 and 14 CFR Part 21, eligibility for a Part 23 type certificate or supplemental type certificate (STC) is open to any individual, corporation, research institution, or foreign entity seeking airworthiness approval for fixed-wing aircraft meeting the following criteria:

  • Passenger Seating Capacity: A maximum passenger seating configuration of 19 or fewer passengers, excluding required flight crew seats (§ 23.2005).
  • Maximum Takeoff Weight (MTOW): A maximum certificated takeoff weight of 19,000 pounds (8,618 kg) or less (§ 23.2005).
  • Vehicle Category: Fixed-wing normal category airplanes. Amendment 23-64 consolidated the former utility, acrobatic, and commuter airplane categories into a single normal category.
  • Applicant Prerequisites: The applicant must demonstrate the engineering capability, quality systems, and data rights under 14 CFR Part 21 necessary to substantiate design compliance through ground, structural, and flight testing.

Under 14 CFR § 23.2005, the FAA establishes a risk-differentiated certification matrix based on airplane certification level and design airspeed:

  • Level 1: Airplanes configured for 0 to 1 passenger, including light sport and experimental proof-of-concept aircraft.
  • Level 2: Airplanes configured for 2 to 6 passengers, covering the core general aviation fleet of single-engine and light twin-engine aircraft.
  • Level 3: Airplanes configured for 7 to 9 passengers, encompassing high-performance turboprops and light utility aircraft.
  • Level 4: Airplanes configured for 10 to 19 passengers, representing small regional commuter aircraft.

Performance classifications divide aircraft into two operational regimes: low-speed airplanes, where normal operating limit speed (VNO) or maximum operating limit speed (VMO) is under 250 knots calibrated airspeed (KCAS) and maximum operating limit Mach number (MMO) is under 0.6; and high-speed airplanes, where VNO or VMO is 250 KCAS or greater, or MMO is 0.6 or greater.

What it funds or requires

14 CFR Part 23 does not provide financial grants; instead, it establishes mandatory airworthiness standards that govern every physical and functional aspect of an aircraft design. The regulation is organized into seven core subparts:

  • Subpart A – General (§§ 23.2000–23.2010): Defines regulatory applicability, the certification matrix, and the requirement under § 23.2010 to show compliance through FAA-accepted means of compliance (MOC).
  • Subpart B – Flight (§§ 23.2100–23.2165): Establishes flight performance envelopes, minimum climb gradients, stall speeds, stall warning cues, spin characteristics, ground handling stability, and trim authority. For multi-engine airplanes, it mandates one-engine-inoperative (OEI) climb performance and minimum control speed (VMC).
  • Subpart C – Structures (§§ 23.2200–23.2270): Mandates structural design envelopes, limit and ultimate load factors (prescribing an ultimate safety factor of 1.5), flight gust loads, landing gear impact loads, structural fatigue life, damage tolerance, and emergency landing crashworthiness (including dynamic seat testing at 26g forward impact).
  • Subpart D – Design and Construction (§§ 23.2300–23.2335): Covers material qualification, environmental durability, flight control system integrity, fire protection, and containment of high-energy rotating parts (turbines, fan blades, or propeller fragments).
  • Subpart E – Powerplant (§§ 23.2400–23.2440): Governs powerplant installation, fuel storage and distribution, induction air filtration, exhaust venting, ice protection, and reversing mechanisms. Crucially, Amendment 23-64 removed prescriptive references to fossil fuel engines, enabling the certification of electric motors, hybrid drives, and hydrogen fuel cells.
  • Subpart F – Equipment (§§ 23.2500–23.2550): Dictates functional performance and installation safety for avionics, electrical power distribution, flight instruments, navigation systems, and environmental controls. Under § 23.2510, applicants must perform functional hazard assessments (FHA) and system safety assessments (SSA), establishing rigorous probability thresholds for catastrophic, hazardous, and major failure conditions.
  • Subpart G – Flightcrew Interface and Other Information (§§ 23.2600–23.2620): Regulates cockpit ergonomics, pilot controls, visual and auditory warning alerts, emergency exit markings, the Airplane Flight Manual (AFM), and complete Instructions for Continued Airworthiness (ICA) under § 23.2615.

To substantiate compliance, applicants primarily utilize consensus standards accepted by the FAA Administrator. Under 14 CFR § 23.2010, the FAA accepts specifications published by ASTM Committee F44, principally ASTM F3264 (Standard Specification for Normal Category Aeroplanes Certification). ASTM F3264 serves as an umbrella matrix referencing subordinate standards such as ASTM F3173 for flight characteristics, ASTM F3116 for structures, ASTM F3061 for systems, and ASTM F3064 for powerplant installations.

This reliance on voluntary consensus standards reflects broader federal regulatory practices, comparable to frameworks seen in FDA recognized consensus standards, where federal regulators cite independent standards development organizations to keep regulatory requirements aligned with rapid technological progress.

Application or compliance steps

Achieving a Part 23 type certificate follows the procedural requirements of 14 CFR Part 21 and the administrative guidance of FAA Order 8110.4C. Applicants must complete six sequential engineering and regulatory stages:

  1. Filing the Type Certificate Application (FAA Form 8110-12): The applicant submits a formal application to the responsible FAA Aircraft Certification Branch, defining the proposed aircraft conceptual design, intended operational envelope, and designated certification level (Levels 1–4, low or high speed).
  2. Establishing the Certification Basis (G-1 Issue Paper): The FAA and the applicant negotiate the G-1 Issue Paper, establishing the regulatory baseline, including applicable amendment levels, special conditions for novel architectures (such as distributed electric propulsion), exemptions, and equivalent level of safety (ELOS) findings.
  3. Developing the Project Specific Certification Plan (PSCP): The applicant drafts a PSCP detailing the compliance matrix. For every applicable section of Part 23, the plan identifies the specific Means of Compliance (MOC)—whether citing accepted ASTM consensus standards via FAA Advisory Circular AC 23.2010-1 or proposing a bespoke applicant MOC requiring direct FAA engineering review.
  4. Conformity Inspection and Test Article Readiness: Before ground or flight testing can generate official certification credit, prototype aircraft, structural rigs, and test instrumentation undergo conformity inspections by FAA Aviation Safety Inspectors or Designated Engineering Representatives (DERs) to verify that test articles conform to engineering drawings.
  5. Ground, Structural, and Environmental Testing: The applicant conducts static limit load testing without permanent deformation, ultimate load testing (1.5 times limit load sustained for at least 3 seconds), flutter testing, system hazard testing, software verification (DO-178C), hardware qualification (DO-254), and environmental testing (DO-160G). In academic and advanced developmental labs, aerodynamic validation often begins in facilities like the Unitary Plan Wind Tunnel to determine transonic drag and control stability before airframe tooling freeze.
  6. Flight Test Campaign and Type Board Review: The flight test program validates handling qualities, stall dynamics, spin resistance, climb performance, engine cooling, and flight deck workload. Following flight test completion and FAA review of the Airplane Flight Manual (AFM) and Instructions for Continued Airworthiness (ICA), the FAA issues the Type Certificate and Type Certificate Data Sheet (TCDS).

Throughout aircraft development, engineering teams must maintain strict export compliance. Advanced flight control software, navigation algorithms, and propulsion models frequently intersect dual-use export classifications, requiring institutional familiarity with ITAR regulations and international export license determinations.

Typical timeline phases (no calendar dates as facts)

Certification timelines under 14 CFR Part 23 depend on design novelty, applicant maturity, and the chosen means of compliance. Rather than rigid calendar dates, the certification lifecycle progresses across distinct technical phases:

  • Phase 1: Conceptual Architecture and Regulatory Strategy: Sizing, structural layout, propulsion selection, and system architectures are established. The team maps the vehicle to the § 23.2005 certification matrix and identifies areas where consensus standards may not yet exist for novel design features.
  • Phase 2: Formal Application and FAA Familiarization: Submitting FAA Form 8110-12 initiates the three-year application window under 14 CFR § 21.17 (extendable upon FAA review). FAA engineers review the design during familiarization briefings and draft initial issue papers.
  • Phase 3: Certification Plan Approval and MOC Agreement: The PSCP and compliance methodology documents are reviewed and signed by the FAA Aircraft Certification Office. Early concurrence on means of compliance prevents costly re-testing.
  • Phase 4: Detailed Design, Analysis, and Component Qualification: Finite element modeling, computational fluid dynamics, and bench testing are conducted. Subcontracted avionics, electrical harnesses, and actuators complete laboratory environmental qualification.
  • Phase 5: Prototype Manufacturing and Conformity: Prototype flight test vehicles and dedicated ground-test structural articles are manufactured under documented quality systems. Conformity inspections verify that prototypes accurately represent the type design.
  • Phase 6: Verification Testing (Ground and Flight): Static structural pull tests, ground vibration testing (GVT), systems integration testing, and formal flight tests are conducted. Test data is compiled into formal compliance reports signed by authorized representatives.
  • Phase 7: Final Approvals, Flight Manual Signing, and TCDS Issuance: The FAA Type Certification Board conducts final reviews, the Aircraft Evaluation Division approves maintenance instructions, the AFM is signed, and the FAA issues the Type Certificate.

Common mistakes

Aeronautical development programs frequently encounter avoidable delays when certifying under 14 CFR Part 23. The most common mistakes include:

  • Assuming Consensus Standards Are Mandatory Rather Than Optional: Many engineering teams assume ASTM F44 consensus standards are rigid statutory mandates. Under 14 CFR § 23.2010 and AC 23.2010-1, consensus standards represent an accepted means of compliance, not the sole path. Applicants remain free to propose alternative means of compliance (AMOC) tailored to novel architectures, provided they demonstrate equivalent safety to the FAA.
  • Over-Specifying the Initial Certification Basis: Applicants sometimes prematurely commit to unnecessary voluntary standards or higher certification levels (such as opting for Level 3 standards on a Level 2 airframe) without anticipating the compounding costs of software design assurance, dynamic seat testing, and redundant electrical busses.
  • Late Execution of Functional Hazard Assessments (FHA): Deferring system safety assessments under § 23.2510 until prototype fabrication is a serious mistake. If an FHA later identifies a flight control failure condition as “catastrophic” rather than “hazardous,” the system must incorporate triple or quadruple redundancy, forcing costly redesigns.
  • Overlooking Instructions for Continued Airworthiness (ICA): Engineering teams often focus exclusively on flight testing, leaving maintenance manuals and airworthiness limitations sections (ALS) as afterthoughts. The FAA will not issue a Type Certificate under 14 CFR § 23.2615 until complete, verified ICAs are delivered.
  • Underestimating Quality Assurance and Conformity Traceability: Conducting development testing on un-conformed prototype hardware yields data that the FAA cannot credit toward certification. Every test intended for compliance must follow formal test plans with verified conformity documentation. Maintaining rigorous institutional quality standards aligns directly with institutional federal contract compliance protocols across university and industry research laboratories.

The table below compares 14 CFR Part 23 with adjacent Federal Aviation Regulations governing civil aeronautical certification and approvals:

Regulation Category & Title Vehicle / Scope Threshold Primary Safety Baseline Governing Focus
14 CFR Part 21 Certification Procedures for Products and Parts All aircraft, aircraft engines, propellers, and appliances Procedural & Quality Assurance Administrative procedures for Type Certificates, Production Certificates, Airworthiness Certificates, and STCs.
14 CFR Part 23 Airworthiness Standards: Normal Category Airplanes 19 or fewer passengers; MTOW ≤ 19,000 lbs Performance-Based (Amdt 23-64) Airworthiness design and safety standards for light, general aviation, utility, and commuter airplanes.
14 CFR Part 25 Airworthiness Standards: Transport Category Airplanes More than 19 passengers or MTOW > 19,000 lbs Prescriptive & Probabilistic Safety Commercial airliners, cargo transports, and large business jets operating under airline transport rules.
14 CFR Part 27 Airworthiness Standards: Normal Category Rotorcraft Rotorcraft with MTOW ≤ 7,000 lbs; 9 or fewer passenger seats Prescriptive & Performance Safety Structural, aerodynamic, and powerplant safety standards for light and medium civilian helicopters.
14 CFR Part 29 Airworthiness Standards: Transport Category Rotorcraft Rotorcraft with MTOW > 7,000 lbs or > 9 passenger seats Enhanced System & Structural Safety Heavy civil and offshore transport helicopters requiring multi-engine Category A engine isolation.
14 CFR Part 33 Airworthiness Standards: Aircraft Engines Reciprocating, turboprop, turbofan, and electric aircraft engines Component Structural & Operability Safety Engine block containment, blade-off testing, bird ingestion, flameout margin, and engine control system safety.

The dataset below outlines the specific airplane certification levels, speed boundaries, and safety risk criteria codified under 14 CFR Part 23 Amendment 23-64.

Frequently Asked Questions

What is the primary difference between 14 CFR Part 23 and 14 CFR Part 25?

The primary dividing line between 14 CFR Part 23 and 14 CFR Part 25 is passenger capacity and gross takeoff weight. Part 23 applies to normal category airplanes configured for 19 or fewer passengers with a maximum certificated takeoff weight of 19,000 pounds or less. Part 25 governs transport category airplanes exceeding these thresholds, including commercial jetliners and heavy corporate aircraft, applying more extensive systems redundancy and transport-category operational safety mandates.

How did Amendment 23-64 change FAA airplane certification?

Amendment 23-64 replaced rigid, prescriptive design rules with objective, performance-based airworthiness standards. Instead of dictating specific engineering designs, the regulation defines safety objectives and permits applicants to demonstrate compliance using FAA-accepted industry consensus standards, such as those maintained by ASTM International Committee F44. This reform significantly reduces the time and cost required to introduce novel technologies like electric propulsion, digital flight controls, and composite structures.

What are the four airplane certification levels in Part 23?

Under 14 CFR § 23.2005, certification levels are defined by passenger seating configuration (excluding flight crew): Level 1 covers 0 to 1 passenger; Level 2 covers 2 to 6 passengers; Level 3 covers 7 to 9 passengers; and Level 4 covers 10 to 19 passengers. Required system safety rigor and structural substantiation increase progressively from Level 1 to Level 4.

What role does ASTM F3264 play in Part 23 compliance?

ASTM F3264 is the primary consensus standard specification recognized by the FAA as an accepted Means of Compliance (MOC) under 14 CFR § 23.2010. It maps specific consensus engineering standards covering flight handling, structures, powerplant, and avionics to the corresponding performance-based subparts of Part 23, providing a clear compliance roadmap for applicants.

Can electric or hybrid aircraft be certified under 14 CFR Part 23?

Yes. By replacing prescriptive references to internal combustion and turbine engines with technology-neutral performance requirements in Subpart E (Powerplant), Amendment 23-64 established a regulatory foundation directly accommodating electric motors, battery packs, and hybrid powerplants without requiring the extensive special conditions previously mandated under legacy regulations.

What is a G-1 Issue Paper in FAA type certification?

The G-1 Issue Paper is the foundational regulatory agreement between an aircraft certification applicant and the FAA Aircraft Certification Service. It establishes the formal certification basis for the project, listing all applicable Part 23 amendment levels, required special conditions for novel design features, exemptions, and equivalent level of safety determinations.

Sources

  • Federal Aviation Administration (FAA). Electronic Code of Federal Regulations: Title 14, Chapter I, Subchapter C, Part 23 — Airworthiness Standards: Normal Category Airplanes. Codified at 14 CFR Part 23. Accessed 2026-11-13 at https://www.ecfr.gov/current/title-14/chapter-I/subchapter-C/part-23.
  • Federal Aviation Administration (FAA). Revision of Airworthiness Standards for Normal, Utility, Acrobatic, and Commuter Category Airplanes (Final Rule; Amendment 23-64). 81 FR 96572, Docket No. FAA-2015-1621. Published December 30, 2016; effective August 30, 2017. Accessed 2026-11-13 at https://www.federalregister.gov/documents/2016/12/30/2016-30246/revision-of-airworthiness-standards-for-normal-utility-acrobatic-and-commuter-category-airplanes.
  • Federal Aviation Administration (FAA). Advisory Circular AC 23.2010-1: FAA Accepted Means of Compliance Process for 14 CFR Part 23. U.S. Department of Transportation, Aircraft Certification Service. Accessed 2026-11-13 at https://www.faa.gov/regulations_policies/advisory_circulars/index.cfm/go/document.information/documentID/1031317.
  • ASTM International. ASTM F3264: Standard Specification for Normal Category Aeroplanes Certification. ASTM Committee F44 on General Aviation Aircraft. West Conshohocken, PA. Accessed 2026-11-13 at https://www.astm.org/f3264-21.html.
  • Federal Aviation Administration (FAA). Order 8110.4C: Type Certification. Aircraft Certification Service. Accessed 2026-11-13 at https://www.faa.gov/regulations_policies/orders_notices/index.cfm/go/document.information/documentID/1019623.
  • European Union Aviation Safety Agency (EASA). Certification Specifications for Normal-Category Aeroplanes (CS-23 Amendment 5). Decision 2017/013/R. Accessed 2026-11-13 at https://www.easa.europa.eu/en/document-library/certification-specifications/cs-23-amendment-5.

Data: FAA 14 CFR Part 23 Airplane Certification Levels and Operating Thresholds

Regulatory matrix of airplane certification levels, passenger capacities, speed boundaries, and safety risk criteria compiled from 14 CFR Part 23 (Amendment 23-64) and FAA Advisory Circular AC 23.2010-1.

Period covered: 2017/2026. Coverage: United States.

FAA 14 CFR Part 23 Airplane Certification Levels and Operating Thresholds
Certification TierPassenger Seating CapacityMaximum Takeoff Weight (lbs)Low-Speed Boundary (Vno/Vmo) (knots CAS)Mach Number Limit (Mmo) (Mach)Primary Consensus Standard Suite
Level 1 (Low-Speed)0 to 1 passenger190002500.6ASTM F3264 / F3061 / F3116
Level 1 (High-Speed)0 to 1 passenger190002500.6ASTM F3264 / F3061 / F3116
Level 2 (Low-Speed)2 to 6 passengers190002500.6ASTM F3264 / F3061 / F3116
Level 2 (High-Speed)2 to 6 passengers190002500.6ASTM F3264 / F3061 / F3116
Level 3 (Low-Speed)7 to 9 passengers190002500.6ASTM F3264 / F3061 / F3116
Level 3 (High-Speed)7 to 9 passengers190002500.6ASTM F3264 / F3061 / F3116
Level 4 (Low-Speed)10 to 19 passengers190002500.6ASTM F3264 / F3061 / F3116
Level 4 (High-Speed)10 to 19 passengers190002500.6ASTM F3264 / F3061 / F3116

Follow CASRAI

Research-administration guidance, standards updates and independent tool reviews.

Ask CASRAI · full access

Ask about 14 CFR Part 23: Airworthiness Standards for Normal Category Airplanes

Full access: large monthly usage, up to 10 source passages behind each answer, and MCP and API access for Claude Code, Codex and other CLIs. Cancel any time.

An AI assistant for research: funder rules, compliance, methods and publishing. It links the sources behind its answers and labels answers that come from a web search.

Answers draw on CASRAI's guides and dictionary plus the federal and funder documents we index: Federal Register, Grants.gov, Regulations.gov and UKRI.

Works on this site and inside Claude, Cursor and the AI tools you already use.

Everything CASRAI publishes — this page, the dictionary, the guides and the news — stays open to read, with no account and no card.

Referenced across the research world

University of Cambridge logoColumbia University logoCrossref logoUniversity of Edinburgh logoHarvard University logoUniversity of Oxford logoPrinceton University logoStanford School of Medicine logoUniversity College London logoORCID logoUniversity of Cambridge logoColumbia University logoCrossref logoUniversity of Edinburgh logoHarvard University logoUniversity of Oxford logoPrinceton University logoStanford School of Medicine logoUniversity College London logoORCID logo
  • University of Cambridge logo
  • Columbia University logo
  • Crossref logo
  • University of Edinburgh logo
  • Harvard University logo
  • University of Oxford logo
  • Princeton University logo
  • Stanford School of Medicine logo
  • University College London logo
  • ORCID logo

View CASRAI adoption →