Skip to main content
v2026.11,986 entries · CC-BY 4.0
LAC HealthSponsored

Shop bain circuit supplies

  • FDA registered
  • ISO 13485
  • BBB Accredited A+

Shop at LAC Health

Bain Circuit: What It Is, How It Is Built and How to Check It

Bain circuit: what it is, its co-axial design, FDA Class I status, and the bypass and occlusion tests described for the inner tube.

Written and maintained by CASRAI Editorial Board

Published · Last updated

This page describes products and general use; it is not medical advice.

On this page

Who uses it: anesthesia providers, operating-room and biomedical staff, and the buyers and students who need to understand what a Bain circuit is and how it is checked before use.

What is a Bain circuit?

A Bain circuit is a lightweight, co-axial (tube-within-a-tube) anesthesia breathing circuit. It was introduced in 1972 by Bain and Spoerel (LITFL). Its purpose is the same as any anesthesia breathing circuit: to carry gases to the patient and away again.

In U.S. regulation, the Bain circuit falls under the generic device type “anesthesia breathing circuit” in 21 CFR 868.5240, defined as a device intended to administer medical gases to a patient during anesthesia. It provides both an inhalation and an exhalation route and may include a connector, adaptor and Y-piece. It is Class I (general controls) and exempt from premarket notification, subject to the limitations in 21 CFR 868.9 (Cornell LII copy of the CFR, checked 2026-10-31).

How a Bain circuit is built

LITFL’s biography page on James Bain describes a tube-within-a-tube about 1.8 m long, with a reservoir bag and valve at the non-patient end, the fresh gas carried in the inner tube, and describes the design as a modified Mapleson D system. Because the fresh gas runs inside the outer tube carrying expired gas, LITFL lists counter-current warming and humidification among its advantages, along with a relocated adjustable pressure-limiting (APL) valve that sits away from the surgical field.

Types and variants

Variant Difference Source
Modified Mapleson D (standard Bain) Reservoir bag with a valve at the non-patient end LITFL, “James Bain”
Mapleson E arrangement Open-ended bag with no valve LITFL, “James Bain”

Dimensions that matter

Part Value reported Source
Overall length about 1.8 m LITFL, “James Bain”
Inner tube (fresh gas) 7 mm LITFL, “James Bain”
Outer tube (expired gas) 22 mm LITFL, “James Bain”

Actual dimensions vary by product; the manufacturer’s instructions for use govern.

Checking the inner tube before use

The inner tube is the weak point of the design. A peer-reviewed case report in the Oman Medical Journal notes that any disconnection or breach of the inner tube’s integrity greatly increases dead-space breathing, and that circuits are often reused after washing. Two equipment checks are described there: a low-pressure (bypass) test and the Foex-Crampton Smith occlusion test, which the report says is more comprehensive and, in a comparison by Szypula and colleagues, more sensitive than the older Pethick test. Follow the manufacturer’s instructions for use and your facility’s equipment-check policy for the exact method.

Safe use and handling basics

Follow the manufacturer’s instructions for checking, cleaning and reuse, and your facility’s equipment-check policy. For related components, see the guides to the endotracheal tube, the ventilator, the PEEP valve, the exhalation valve and the medical water trap. Facilities that stock these items can browse anesthesia circuits.

FAQ

What is a Bain circuit?

A Bain circuit is a co-axial anesthesia breathing circuit, with fresh gas in an inner tube inside a wider outer tube that carries expired gas. It was introduced in 1972 and is classed by the FDA as an anesthesia breathing circuit, Class I.

Is a Bain circuit the same as a Mapleson D?

It is described as a modified Mapleson D system; with an open-ended bag and no valve it becomes a Mapleson E arrangement (LITFL).

How is a Bain circuit checked before use?

Equipment checks of the inner tube, such as the bypass test and the occlusion test, are described in a peer-reviewed case report (Oman Medical Journal, 2010); the manufacturer’s instructions and facility policy govern the method.

Sources

Follow CASRAI

Research-administration guidance, standards updates and independent tool reviews.

Ask CASRAI · free to try

Ask about Bain Circuit: What It Is, How It Is Built and How to Check It

2 free questions a day, no account.

An AI assistant for research: funder rules, compliance, methods and publishing. It links the sources behind its answers and labels answers that come from a web search.

Answers draw on CASRAI's guides and dictionary plus the federal and funder documents we index: Federal Register, Grants.gov, Regulations.gov and UKRI.

Works on this site and inside Claude, Cursor and the AI tools you already use.

Everything CASRAI publishes — this page, the dictionary, the guides and the news — stays open to read, with no account and no card.

Referenced across the research world

University of Cambridge logoColumbia University logoCrossref logoUniversity of Edinburgh logoHarvard University logoUniversity of Oxford logoPrinceton University logoStanford School of Medicine logoUniversity College London logoORCID logoUniversity of Cambridge logoColumbia University logoCrossref logoUniversity of Edinburgh logoHarvard University logoUniversity of Oxford logoPrinceton University logoStanford School of Medicine logoUniversity College London logoORCID logo
  • University of Cambridge logo
  • Columbia University logo
  • Crossref logo
  • University of Edinburgh logo
  • Harvard University logo
  • University of Oxford logo
  • Princeton University logo
  • Stanford School of Medicine logo
  • University College London logo
  • ORCID logo

View CASRAI adoption →