Written and maintained by CASRAI Editorial Board
Published · Last updated
On this page
General device and regulatory information only; this is not medical or dental advice.
Short answer
Dental mercury is liquid elemental mercury supplied for dentistry to be combined with amalgam alloy powder into dental amalgam. FDA regulates it as a Class II device under 21 CFR 872.3070, both as part of dental amalgam and as a component device in its own right. Mercury alone is not the filling: the filling forms only when mercury and alloy are combined.
Definition and scope
The federal regulation for dental amalgam, 21 CFR 872.3070, defines dental amalgam as a device consisting of elemental mercury, supplied as a liquid in bulk, sachet or predosed capsule form, together with amalgam alloy composed primarily of silver, tin and copper, supplied as a powder in bulk, tablet or predosed capsule form, for the direct filling of carious lesions or structural defects in teeth. The same section states that the device also includes the individual component devices, mercury and amalgam alloy, when they are intended to be combined with each other to form dental amalgam (eCFR, checked 2026-10-31).
That wording is the scope of “dental mercury” as a regulated item. The section does not give “dental mercury” a separate definition; it treats mercury as a component of the amalgam device. The section places the device in Class II (special controls), and the special control is FDA’s guidance document “Dental Amalgam, Mercury, and Amalgam Alloy.” FDA’s classification database lists the same regulation number for three entries: Dental Amalgam (product code OIV), Alloy, Amalgam (EJJ) and Mercury (ELY), each Class 2 (openFDA device classification, checked 2026-10-31).
How dental mercury is used in practice
Per the regulation and FDA’s consumer page, dental mercury is not used on its own. It is intended to be combined with amalgam alloy to form dental amalgam, which is then used for direct fillings. FDA states that approximately half (50%) of dental amalgam is elemental mercury by weight, with the remainder a powder of silver, tin and copper (FDA, “Dental Amalgam Fillings,” page content current as of 02/18/2021, checked 2026-10-31). Once placed, FDA says fillings release low levels of mercury as a vapor that can be inhaled and absorbed by the lungs, and that removing intact fillings temporarily increases vapor release.
For the product that holds and delivers the combined material, see the guide to the amalgam capsule; for the instrument that carries it, see the amalgam carrier.
Supply forms: mercury and alloy side by side
The regulation names the forms in which each component is supplied. Every row below comes from the 21 CFR 872.3070(a) wording.
| Component | Physical state in the regulation | Supply forms named |
|---|---|---|
| Mercury | Elemental mercury, supplied as a liquid | Bulk, sachet, predosed capsule |
| Amalgam alloy | Alloy composed primarily of silver, tin and copper, supplied as a powder | Bulk, tablet, predosed capsule |
Both components can be supplied in a predosed capsule, which is the form the regulation names for each. The regulation says nothing further about which form a given practice should use, so this page does not either.
Where it matters for clinics and labs
- Classification. Mercury intended to be combined with alloy is itself a Class II device under 872.3070, so product records for it carry a regulation number and product code (ELY) rather than being treated as a bare chemical.
- Alternatives. For how the two filling families are classified side by side, see amalgam vs composite and the dental composite resin guide.
- Disposal is a separate regime. FDA states that it does not regulate the environmental safe handling or disposal of dental amalgam; EPA, state and local authorities do. The wastewater side is covered in the dental amalgam separator guide.
Common misunderstandings
“Dental mercury is the filling.”
No. The filling is dental amalgam, which is mercury combined with a silver, tin and copper alloy. The regulation lists mercury and alloy as individual component devices that become amalgam only when intended to be combined.
“Amalgam contains only a trace of mercury.”
FDA states that approximately 50% of dental amalgam is elemental mercury by weight.
“FDA also regulates how amalgam waste is disposed of.”
FDA says it does not; environmental handling and disposal fall to EPA, state and local authorities.
“Elemental mercury in dentistry is the same as the mercury behind general mercury hazards.”
Mercury occurs in several chemical forms with different hazard profiles; see why mercury is dangerous for the general picture. This page covers only the dental device context.
FAQ
What is dental mercury?
Liquid elemental mercury supplied for combining with amalgam alloy to make dental amalgam, regulated by FDA as a Class II device component under 21 CFR 872.3070.
Is dental mercury regulated separately from amalgam?
It has its own classification entry (Mercury, product code ELY, Class 2) under the same regulation number as dental amalgam, because the regulation includes the individual components when intended to be combined.
In what forms is dental mercury supplied?
The regulation names bulk, sachet and predosed capsule forms.
How much of dental amalgam is mercury?
Approximately half, by weight, according to FDA.
Does FDA regulate how amalgam waste is disposed of?
No. FDA states that it does not regulate the environmental safe handling or disposal of dental amalgam; EPA, state and local authorities do.
Sources
- U.S. eCFR, 21 CFR 872.3070, Dental amalgam, mercury, and amalgam alloy: https://www.ecfr.gov/current/title-21/chapter-I/subchapter-H/part-872/subpart-D/section-872.3070 (checked 2026-10-31).
- U.S. FDA, Dental Amalgam Fillings (content current as of 02/18/2021): https://www.fda.gov/medical-devices/dental-devices/dental-amalgam-fillings (checked 2026-10-31).
- U.S. FDA, openFDA device classification API, regulation number 872.3070: https://open.fda.gov/apis/device/classification/ (checked 2026-10-31).







