Written and maintained by CASRAI Editorial Board
Published · Last updated
On this page
General product information only, not medical advice. This page is for the person who stocks, specifies or buys a finger-injury station and needs a checklist of what the kit should contain and what to ask the supplier. It does not explain how to treat an injury.
Purpose and setting
A finger injury kit is a pre-assembled set of supplies kept where finger injuries could happen, typically a finger splint, a wrap or tape, gauze and a cold pack. Contents vary widely: typical consumer kits hold a few items, while clinical kits are built around a range of splint sizes. The checklist below separates the two so you can specify the right one for your site.
This page does not repeat what each product is. For that, see finger splint types, stack splints, buddy tape and what a splint is. For a general splint assortment beyond fingers, see splint kits.
Checklist table
Items are grouped by category. The two kit columns describe what is typical for the example kit shown, not a required list: no standard names finger splints as mandatory kit content.
| Category | Item | Typical consumer kit | Typical clinical size-assortment kit | What to check |
|---|---|---|---|---|
| Immobilization | Finger splints | One splint (for example metal or foam) | Many splints across a size range; one example kit holds 44 molded plastic splints in sizes 2 to 15 | Size range and count per size |
| Immobilization | Finger bands or tape | Sometimes two finger bands | Not part of the example splint kit | Whether fixation is included or sold separately |
| Dressing | Gauze tube or gauze | One gauze tube in some kits | Not part of the example splint kit | Pack size and sterile or non-sterile labeling |
| Cold | Gel pack or ice sleeve | One gel pack or ice sleeve in some kits | Not part of the example splint kit | Single-use or reusable, per the maker |
| Fitting | Sizing aid | Not typical | Sold separately for the example kit | Included or a separate order |
| Inspection | Penlight | Not typical | One in the example kit | Batteries and replacement |
| Documentation | Instructions | Usually a leaflet | Included in the example kit | The maker’s instructions for use |
| Storage | Case or container | Varies | Carrying case in the example kit | Fits the station and is easy to find |
Consumer kits versus clinical kits (finger splint kit)
A consumer finger injury kit is built as a single-use bundle: one splint, one gauze tube and a cold pack are a common pairing in retail listings. A clinical finger splint kit is built the other way around. It stocks one product type in many sizes so that a clinician can match a splint to different fingers. In one example (the Alimed Oval-8 Finger Splint Kit), the maker lists 44 splints across sizes 2 to 15, with counts per size peaking at five for the mid-range sizes and falling to one at size 15, plus a penlight, instructions and a carrying case. The maker describes the splints as aligning and stabilizing the PIP and DIP joints, and sells a sizing set separately.
The practical difference for a buyer is the question to ask. For a consumer-style kit the question is which items are included. For a size-assortment kit the question is which sizes and how many of each, and whether the sizing aid is in the box.
What varies by facility type
No fixed kit contents are prescribed here by facility type. What does vary is who sets the contents. Under the federal workplace first aid rule, the employer decides what supplies are adequate for the site. Larger or multiple operations determine their own additional quantities and types of supplies. The decision rests with the person responsible for the site.
Storage, expiry and restocking
Shelf life for finger-injury kit contents comes from the maker’s own labeling. Check each component’s label for lot numbers and date codes, and follow the maker’s instructions for storage and use. Record what was used and replace it so the size range stays complete. Cold packs and gauze are separate products from splints and carry their own labeling.
Standards that apply
- OSHA 29 CFR 1910.151(b) (eCFR, checked 2026-11-01): where no infirmary, clinic or hospital is in near proximity to the workplace for treating all injured employees, a person or persons must be adequately trained to render first aid, and adequate first aid supplies must be readily available.
- 29 CFR 1910.151 Appendix A (non-mandatory): describes a minimal generic kit as the contents of ANSI Z308.1-1998 and says that kit should be adequate for small worksites. For larger or multiple operations, the employer determines additional quantities and types.
- ANSI/ISEA Z308.1-2026 (ISEA, checked 2026-11-01): the current edition of the American National Standard for Minimum Requirements for Workplace First Aid Kits and Supplies. ISEA describes it as covering kit contents, classification, performance and labeling. Check the standard itself for the items a compliant kit holds.
- 21 CFR 890.3475, limb orthosis (eCFR, checked 2026-11-01): defines a limb orthosis as a device worn on the upper or lower extremities to support, correct or prevent deformities or align body structures. It is a Class I device, exempt from premarket notification subject to limits in 890.9. Whether a particular finger splint falls under this regulation depends on the maker’s labeling or FDA product code.
FAQ
What is in a finger injury kit?
Typical consumer kits pair a finger splint with a gauze tube or tape and a gel or ice pack. Clinical kits center on an assortment of splint sizes, sometimes with a penlight, instructions and a case.
What is a finger splint kit?
It is a set of finger splints, usually in several sizes, sold together. In the Alimed example, 44 splints cover sizes 2 to 15, and a sizing set is sold separately.
Does a workplace have to stock one?
OSHA 1910.151(b) requires adequate first aid supplies to be readily available where there is no nearby clinic or hospital. The rule leaves contents to the employer and does not name finger splints.
What should I ask a supplier?
Ask for the size range and count per size, whether a sizing aid is included, the labeling and instructions for use, lot and date codes, and what the kit does not contain.
Sources
All sources below were last checked on 2026-11-01.
- eCFR, 29 CFR 1910.151 and Appendix A, checked 2026-11-01: ecfr.gov
- International Safety Equipment Association, ANSI/ISEA Z308.1 first aid standard page, checked 2026-11-01: safetyequipment.org
- eCFR, 21 CFR 890.3475 Limb orthosis, checked 2026-11-01: ecfr.gov
- Alimed, Oval-8 Finger Splint Kit product page, checked 2026-11-01, cited as an example of a clinical size-assortment kit: alimed.com
