Written and maintained by CASRAI Editorial Board
Published · Last updated
On this page
Short answer: The lysine decarboxylase test checks whether a bacterial isolate can remove the carboxyl group from the amino acid L-lysine. In Moeller’s tube method, a lysine-supplemented broth turns from yellow to purple when the enzyme is present, and a paired tube without the amino acid shows whether the colour change is real. The test is read only if the tube was sealed from air with sterile mineral oil.
General laboratory information for technicians and supply staff. It is not medical advice and not a bench protocol; always follow your laboratory’s validated procedure and the manufacturer’s instructions for use.
Definition and scope
Lysine decarboxylase (LDC) activity is one of three reactions Moeller’s decarboxylase broth was introduced to detect, alongside ornithine decarboxylase and arginine dihydrolase (HiMedia Technical Data M393). It is used to differentiate Gram-negative enteric bacilli by their ability to decarboxylate amino acids. The same enzyme reaction is also read in combined media: see lysine iron agar (LIA) for slant and butt reactions, and XLD agar for a plating medium that contains lysine.
How the Moeller tube test works
According to the manufacturer’s technical sheet, the base medium contains peptones, a small amount of dextrose (0.5 g/L), the cofactor pyridoxal, and two pH indicators, bromocresol purple and cresol red. The lysine is added separately by the user.
- Acid phase. Dextrose-fermenting bacteria lower the pH and the broth turns from purple to yellow. The sheet states that this acid “stimulates” the decarboxylase enzyme.
- Amine phase. Decarboxylation of lysine yields cadaverine (ornithine yields putrescine). These amines raise the pH, so the indicator moves from yellow back to purple.
- Negative result. If the organism lacks the enzyme, the medium stays acidic and yellow.
Why the control tube and the oil overlay matter
These two controls decide whether a result can be read at all. Both come from the manufacturer’s sheet.
| Control | What the sheet says | What it protects against |
|---|---|---|
| Tube lacking the amino acid | Each isolate should also be inoculated into a Moeller broth tube without the amino acid. | Lets you compare: a purple colour that also appears without lysine is not evidence of lysine decarboxylation. |
| Sterile mineral oil layer | Inoculated tubes “must be protected from air” with sterile mineral oil; exposure to air may cause alkalinization at the surface, which makes the test invalid. | Surface alkalinization that mimics a positive purple reaction. |
The sheet’s limitations list repeats the point: overlaying with mineral oil is essential, and some fastidious organisms may show a delayed reaction. Treat an unsealed tube, or a purple control tube, as an invalid test rather than a positive one. This is an editorial reading of the manufacturer’s statements.
Lysine decarboxylase test versus LIA and MIL
Tube broth is not the only way to see LDC activity. A 1975 study in the Journal of Clinical Microbiology compared motility-indole-lysine (MIL) medium and lysine iron agar with standard motility, indole and Moeller lysine decarboxylase media for presumptive identification of Enterobacteriaceae, and reported that LIA and MIL detect lysine decarboxylase and deaminase activity equally well (Reller and Mirrett, 1975). The authors described lysine decarboxylase detection as a useful supplement to triple sugar iron and urea agar when looking for enteric pathogens in faecal cultures. The paper is a single, older study, so it supports the idea that the reaction is read in several media, not that one format should replace another.
What to check on a decarboxylase broth base sheet
When a laboratory or supply office compares decarboxylase broth bases, the manufacturer’s technical sheet is the document to read. Based on HiMedia M393, these are the items that sheet states:
- Composition and final pH. Peptone, dextrose, indicators and pyridoxal are listed in g/L, with a stated final pH of about 6.0 at 25 degrees Celsius. The sheet notes that the formula is adjusted and standardized to suit performance parameters, so another maker’s base may differ; do not assume brands are interchangeable.
- Amino acid form. The directions say the amino acid is added by the user and that its form (L- or DL-) and any pH readjustment for ornithine depend on the amino acid used. Check which form your procedure specifies.
- Quality-control organisms. The sheet states cultural response with the amino acid added and a sterile mineral oil overlay, and lists named ATCC control strains including Escherichia coli ATCC 25922, Citrobacter freundii ATCC 8090, Klebsiella aerogenes ATCC 13048 and Klebsiella pneumoniae ATCC 13883. Incubation conditions are set by the sheet and your laboratory procedure.
- Appearance specifications. Powder is light yellow to greenish yellow; prepared medium is purple, clear and without precipitate; a 1.05% w/v solution reads pH 5.80-6.20.
- Intended use labelling. The product is labelled for in vitro diagnostic use, professional use only.
- Disposal. Contaminated materials are to be sterilized by autoclaving before discard; see what an autoclave is and biosafety levels for background.
Common misunderstandings
- “Purple means positive” without conditions. Purple counts only if the medium was first acidified by growth, the tube was oil-sealed, and the no-amino-acid control did not turn purple.
- “A yellow tube is always negative.” The sheet notes some fastidious organisms may react late, so a reading made too early can mislead.
- “All decarboxylase bases are the same.” The manufacturer’s sheet describes an adjusted, standardized formula; compare the sheets, not just the product names.
- “Lysine is the only amino acid.” The same base is used with arginine and ornithine; the sheet notes that ornithine decarboxylase helps separate Klebsiella (nonmotile, no ornithine decarboxylase) from Enterobacter (motile, produce it, except E. agglomerans).
FAQ
What does a lysine decarboxylase test detect?
Whether an isolate produces lysine decarboxylase, the enzyme that converts lysine to cadaverine; the resulting amine raises the pH and turns the indicator purple.
Why does the broth turn yellow first?
Dextrose fermentation produces acid, which turns the indicator yellow and, per the manufacturer, stimulates the decarboxylase enzyme.
Is mineral oil optional?
No. The manufacturer states that exposure to air may cause surface alkalinization that invalidates the test.
Can LIA replace the tube test?
One 1975 comparison found LIA and MIL detect lysine decarboxylase equally well as a presumptive test; local procedures decide which format a laboratory uses.
Sources
- HiMedia Laboratories, Technical Data M393, Decarboxylase Broth Base, Moeller, himedialabs.com/media/TD/M393.pdf. Checked 2026-11-01.
- Reller LB, Mirrett S. Motility-indole-lysine medium for presumptive identification of enteric pathogens of Enterobacteriaceae. J Clin Microbiol. 1975;2(3):247-252. PMC274179. Checked 2026-11-01.







