Skip to main content
v2026.11,986 entries · CC-BY 4.0
LAC HealthSponsored

Shop parts ambu bag supplies

  • FDA registered
  • ISO 13485
  • BBB Accredited A+

Shop at LAC Health

Parts of an Ambu Bag: Names, Functions and What to Check on Each

Part-by-part reference to the parts of an Ambu bag, with each valve explained, which parts are optional, and what to verify before stocking one.

Written and maintained by CASRAI Editorial Board

Published · Last updated

On this page

An Ambu bag is a self-inflating bag-valve-mask resuscitator, and its parts are the ventilation bag, an oxygen inlet, an intake valve, a patient valve and a patient connector, plus an oxygen reservoir and, on some models, a pressure relief (pop-off) valve and a PEEP valve. Buyers and clinic staff who need to read a product listing or inspect a unit can use this page to name each part, say what it does and see which parts vary by model.

This page describes products and general use; it is not medical advice.

What an Ambu bag is made of

“Ambu bag” is the common name for a bag-valve-mask (BVM) resuscitator, as described by the manufacturer and in a peer-reviewed review. For what the device is for and how it differs from other oxygen equipment, see what is a bag-valve-mask. Here the focus is the components, the way a peer-reviewed review in BJA Education lists them (Lee and Yip, 2023). Who uses it: clinic staff, buyers and students who need to name and check the components.

Parts of an Ambu bag, part by part

Part What it does Fixed or model-dependent
Ventilation bag Squeezed by the user to deliver breaths; recoils on its own during expiration and refills from an oxygen source, room air or both. Present on every unit; size varies by model
Oxygen inlet Connects the unit to an oxygen source. Present
Intake valve Made of three soft flap valves (see below) that control which way gas moves at the back of the bag. Present
Oxygen reservoir bag Fills from the oxygen supply so the unit can deliver the highest oxygen concentration available. Listed as a component; confirm it is included with the exact model
Patient valve Keeps gas moving one way only and directs expired gas out through the expiratory port, which prevents rebreathing. Has an inspiratory port, an expiratory port and a patient connector. Present; design varies
Patient (mask) connector Joins the patient valve to a face mask or an airway device. Present
Pressure relief (pop-off) valve Fitted at the inspiratory port of the patient valve to limit excessive pressure. Usually found on paediatric models
PEEP valve Attaches to the expiratory port of the patient valve. Optional; only on some models

Source: Lee CP, Yip YY, “Understanding your bag-valve-mask resuscitator”, BJA Education 2023;23(6):208-211 (see Sources below).

Valves explained: intake, patient and pop-off

The three flap valves in the intake valve

  • Intake disc membrane: makes sure gas goes forward to the patient during manual ventilation and not back into the reservoir bag.
  • Inlet reservoir flap valve: opens to let room air in when the reservoir bag is empty. It is what lets the bag self-inflate.
  • Outlet reservoir flap valve: lets excess gas escape to the atmosphere.

Patient valve designs

The review names two designs: the Ambu single shutter valve and the duckbill valve. It notes that a duckbill design may or may not include an additional expiratory valve. That is a reason to read the model’s description rather than assume all patient valves are built alike.

Pop-off valve

The pop-off valve sits at the inspiratory port of the patient valve and is usually on paediatric models. Pressure settings differ by model, so check the model’s own documentation. See the Ambu bag pop-off valve guide for that part in detail.

Sizes: one manufacturer’s example

The BJA Education review gives bag volumes for one product, the Laerdal Silicone Resuscitator. They show why the two bags on a unit are different parts and why adult and paediatric models are not interchangeable in the listing. They are an example for that model, not a standard.

Part Adult model Paediatric model
Ventilation bag 1600 ml 500 ml
Oxygen reservoir bag 2600 ml 600 ml

Source: Lee and Yip 2023, as above. For sizes by manufacturer for infants, see the infant bag-valve-mask guide.

What to verify on the exact model

These checks are drawn from the cited sources and are not a universal rule.

Check Why it matters Source
Which parts come with the exact model Reservoir, pop-off valve and PEEP valve are described as model-dependent or optional, and the manufacturer notes units are available with a variety of pre-attached accessories. Lee and Yip 2023; Ambu SPUR II product page
Patient valve design Single shutter and duckbill designs differ, and some duckbill designs add an expiratory valve. Lee and Yip 2023
Materials statement The manufacturer of the SPUR II states its bag body is made from SEBS rather than PVC, with no PVC, DEHP or phthalates. This is a manufacturer claim for that product. Ambu SPUR II product page
MR status The same page lists the SPUR II as MR Conditional, so MR status is stated per model. Ambu SPUR II product page
Instructions for use and datasheets The product page lists an IFU and datasheets as downloads; check the model’s own IFU for the standard it declares. Ambu SPUR II product page

Source: Ambu SPUR II product page (see Sources below). For equipment that sits alongside the bag, the emergency oxygen kit checklist lists what else is stocked. Suppliers of related respiratory consumables are grouped under anesthesia circuits.

Safe use and handling basics

Follow the model’s instructions for use, which is the document that governs that product. Training in manual ventilation is separate from reading a parts list, and nothing here replaces it. The reservoir bag and the oxygen inlet only help if an oxygen source is connected, and the outlet reservoir flap valve lets excess gas escape to the atmosphere. Performance figures differ by model, so take them from the model’s own documentation.

Common mistakes

  • Confusing the two bags. The ventilation bag is squeezed; the oxygen reservoir bag only stores oxygen.
  • Assuming every model has a pop-off valve. It is usually a paediatric feature, so check the listing.
  • Assuming a PEEP valve is included. It is optional and fitted only on some models.
  • Treating the brand name as a specification. “Ambu bag” is shorthand; configuration is in the model’s description and IFU.

FAQ

What are the parts of an Ambu bag?

The ventilation bag, oxygen inlet, intake valve, oxygen reservoir bag, patient valve, patient connector, and on some models a pressure relief (pop-off) valve and a PEEP valve (Lee and Yip, 2023).

Which parts vary by model?

The pop-off valve is usually found on paediatric models, the PEEP valve is fitted on some models only, and the patient valve design differs (single shutter or duckbill). Bag volumes also differ by model.

What does the patient valve do?

It keeps gas moving one way and directs expired gas out through the expiratory port, which prevents rebreathing.

Is the reservoir bag the same as the ventilation bag?

No. The ventilation bag is the one that is squeezed to deliver breaths; the reservoir bag fills from the oxygen supply.

Sources

Follow CASRAI

Research-administration guidance, standards updates and independent tool reviews.

Ask CASRAI · free to try

Ask about Parts of an Ambu Bag: Names, Functions and What to Check on Each

2 free questions a day, no account.

An AI assistant for research: funder rules, compliance, methods and publishing. It links the sources behind its answers and labels answers that come from a web search.

Answers draw on CASRAI's guides and dictionary plus the federal and funder documents we index: Federal Register, Grants.gov, Regulations.gov and UKRI.

Works on this site and inside Claude, Cursor and the AI tools you already use.

Everything CASRAI publishes — this page, the dictionary, the guides and the news — stays open to read, with no account and no card.

Referenced across the research world

University of Cambridge logoColumbia University logoCrossref logoUniversity of Edinburgh logoHarvard University logoUniversity of Oxford logoPrinceton University logoStanford School of Medicine logoUniversity College London logoORCID logoUniversity of Cambridge logoColumbia University logoCrossref logoUniversity of Edinburgh logoHarvard University logoUniversity of Oxford logoPrinceton University logoStanford School of Medicine logoUniversity College London logoORCID logo
  • University of Cambridge logo
  • Columbia University logo
  • Crossref logo
  • University of Edinburgh logo
  • Harvard University logo
  • University of Oxford logo
  • Princeton University logo
  • Stanford School of Medicine logo
  • University College London logo
  • ORCID logo

View CASRAI adoption →