Skip to main content
v2026.11,986 entries · CC-BY 4.0
LAC HealthSponsored

Shop 50 ml conical tube supplies

  • FDA registered
  • ISO 13485
  • BBB Accredited A+

Shop at LAC Health

50 mL Conical Tube: Specifications, Types & Safe Use

Explore 50 mL conical tube specifications, materials, RCF ratings across rotors, cap styles, chemical resistance, and clinical laboratory safety standards.

Written and maintained by CASRAI Editorial Board

Published

On this page

A 50 mL conical tube is a rigid, graduated laboratory consumable molded from medical-grade polypropylene, engineered to concentrate, separate, and store liquid biological samples and reagents under high centrifugal force. Featuring a standardized 30 mm outer diameter, conical tapered base, leakproof threaded cap, and Relative Centrifugal Force ratings up to 16,000 to 20,000 × g, the 50 mL conical tube serves as the primary vessel for cell culture pelleting, macromolecular precipitation, clinical specimen handling, and cryogenic storage across life science laboratories.

This page describes products and general use; it is not medical advice.

Who uses it: Cell biologists, clinical laboratory scientists, analytical biochemists, and lab procurement specialists use 50 mL conical tubes for cell culture harvesting, density gradient centrifugation, reagent batching, and biospecimen storage.

What a 50 mL Conical Tube Is and Its Primary Laboratory Functions

The 50 mL conical tube—commonly called a Falcon-style tube after the pioneering brand—is a foundational piece of consumable laboratory plasticware. Unlike flat-bottom tubes or cylindrical vials, the conical tip concentrates small volumes of cellular or particulate matter into a tight, easily visualized pellet at the apex of the tube. While the nominal working capacity is 50 mL, total overflow volume is typically 52 to 54 mL, providing sufficient headspace to prevent liquid contact with the cap during vortexing or thermal expansion.

In biomedical workflows, 50 mL conical tubes perform three primary roles: cell culture harvesting, chemical reaction processing, and biospecimen preservation. During cell passaging, trypsinized cell suspensions are collected into 50 mL tubes, pelleted by gentle centrifugation (200 to 400 × g), and separated from growth media by aspirating the supernatant without disturbing the pellet. In molecular biology, these tubes serve as reaction vessels for plasmid DNA purification, total RNA precipitation, and protein salting-out. In clinical diagnostics, 50 mL tubes are regulated under FDA 21 CFR 864.3250 as Class I specimen transport containers used for processing urine sediments, sputum samples, and pleural fluid. Researchers can review broader conical centrifuge tube designs to understand how 50 mL units interface with smaller 15 mL and microcentrifuge formats.

Materials, Anatomy, and Precision Engineering Dimensions

The engineering of a modern 50 mL conical tube balances mechanical strength, optical clarity, chemical inertness, and thermal stability. The tube body is injection-molded from virgin medical-grade polypropylene (PP) homopolymer or copolymer. Polypropylene provides high tensile strength under hydrostatic pressure while resisting stress-cracking from organic solvents and laboratory detergents. Leading manufacturers certify resins under United States Pharmacopeia (USP) Class VI biological reactivity standards, ensuring the material contains no cytotoxic agents or heavy metals. Premium tubes are manufactured without slip agents (such as oleamide or erucamide), plasticizers, or biocides that could leach into solutions and interfere with spectrophotometry, mass spectrometry, or enzymatic assays. For a detailed polymer comparison, see our analysis of polypropylene vs polystyrene labware regarding tensile modulus, solvent resistance, and optical clarity tradeoffs.

Standard dimensions are tightly controlled to ensure compatibility across centrifuges, automation decks, and storage racks:

  • Outer Body Diameter: 29.5 to 30.0 mm along the cylindrical barrel, expanding to 34.0 to 35.0 mm at the cap rim.
  • Total Height with Cap: 114.0 to 118.0 mm (standardized at 115.0 mm across most manufacturers).
  • Conical Tip Angle: An internal apex taper of approximately 60 degrees, terminating in a rounded bottom radius (2 to 3 mm) to distribute hydrostatic load without stress concentration.
  • Wall Thickness: Sidewalls maintain 1.0 to 1.2 mm thickness, thickening to 1.5 to 1.8 mm near the conical apex to resist compression in rotor cavities.

Caps are molded from High-Density Polyethylene (HDPE) or polypropylene. HDPE caps provide excellent sealing compliance because the softer polyethylene conforms tightly against the rigid polypropylene rim. Most tubes feature dual-start continuous threads allowing rapid three-quarter-turn closure without cross-threading. Printed or molded graduations span 5 mL to 50 mL in 2.5 mL or 5 mL increments. These graduation marks are calibrated for rough estimation with an error tolerance of ±2% to ±5%; analytical dispensing must always use calibrated volumetric pipettes. A matte white writing patch provides a chemically resistant surface for cryogenic markers and barcode labels.

Design Variants: Conical vs. Skirted and Cap Configurations

Standard conical-bottom tubes require dedicated laboratory tube racks to stand upright, but they concentrate pellets efficiently and fit snugly into conical rotor cushions. In contrast, skirted (self-standing) tubes feature a molded outer cylindrical base that allows the tube to stand upright unsupported on benchtops, biosafety cabinets, and robotic liquid handler decks. However, the skirt creates an unsupported gap beneath the inner cone that concentrates mechanical stress during centrifugation, lowering the maximum RCF limit from 16,000–20,000 × g down to 3,000–8,000 × g.

Closure styles are tailored to operational workflows:

  • Flat-Top Screw Caps: Provide a smooth, flat surface suitable for labeling and allow inverted placement on sterile surfaces. An internal sealing lip seals against the inner tube neck.
  • Plug-Seal Caps: Feature an extended plug that fits deep into the tube lumen, establishing an aggressive radial seal that resists leaking during orbital shaking, vortexing, and courier transport.
  • SnapTec / Flip-Top Lids: Feature a hinged snap-cap mechanism attached to the collar, enabling single-handed opening and closing in sterile cell culture hoods without setting caps on bench surfaces.

Smooth conical tip

Flat-top HDPE screw cap

16,000 to 20,000 × g

High-speed cell pelleting, macromolecular isolation; requires tube rack.

Conical with outer molded skirt

Flat-top or plug-seal cap

3,000 to 8,000 × g

Automated liquid handlers, benchtop reagent reservoirs; reduced RCF tolerance.

Smooth conical tip

Opaque screw cap

12,000 to 16,000 × g

Storage of light-sensitive compounds, fluorophores, vitamins, and dyes.

Smooth conical tip

Integrated hinged snap lid

Up to 17,000 × g

Rapid cell culture harvesting and aseptic reagent handling without setting caps down.

Reinforced conical apex

Reinforced screw cap

Up to 20,000 × g

High-speed density gradient separations (cesium chloride, sucrose cushions).

Tube Variant Base Geometry Cap Style Centrifugal Limit (RCF) Primary Application & Operational Tradeoff
Standard High-Clarity Conical
Skirted Self-Standing
Amber / Light-Blocking Conical
Single-Handed Flip-Top (SnapTec)
Heavy-Wall High-RCF Conical

Centrifugal Dynamics, Rotor Compatibility, and RCF Limits

Centrifugal intensity must always be specified in Relative Centrifugal Force (RCF, × g) rather than revolutions per minute (RPM). The RCF experienced by a sample depends on rotational speed and rotor radius according to the formula RCF = 1.118 × 10⁻⁵ × r × (RPM)², where r is the radius in centimeters from the spindle axis to the farthest point of the tube cavity. Protocols should consult our reference to convert RPM to relative centrifugal force to verify exact rotor calculations.

Rotor configuration determines the stress profile and safe speed limits of 50 mL conical tubes:

  • Fixed-Angle Rotors: Tubes sit at a fixed angle (typically 30° to 45°). Hydrostatic pressure forces the fluid column against the outward-facing sidewall. High-clarity polypropylene tubes withstand 16,000 to 20,000 × g in fixed-angle rotors, but only when fully supported by precision-machined conical inserts. Operating an unadapted tube can cause sidewall collapse or bottom puncture. Detailed rotor designs are covered in our guide to centrifuge rotor types.
  • Swinging-Bucket Rotors: Buckets swing horizontal (90°) during rotation, directing centrifugal force down the longitudinal axis into the conical tip. Because the entire 50 mL liquid column presses into the bucket cushion, axial compression is severe. Consequently, commercial 50 mL conical tubes are derated to 3,000 to 3,500 × g in swinging-bucket rotors. Exceeding 3,500 × g in swinging buckets will crush the conical apex.

The data table below summarizes physical dimensions, rotor-specific RCF ratings, and thermal parameters across leading commercial 50 mL conical centrifuge tube models from five primary scientific manufacturers.

25° to 45°

Diagonal lateral vector against outer sidewall

16,000 to 20,000 × g

Full-contact conical rotor cavities or precision conical polyurethane adapters.

90° (horizontal)

Direct axial vector into conical apex

3,000 to 3,500 × g

Rubber bottom cushions and multi-place round bucket inserts with conical cutouts.

45°

Lateral vector with partial neck support

6,000 to 9,400 × g

Split polymer inserts; requires derating if liquid density exceeds 1.2 g/mL.

Rotor Configuration Typical Angle Force Vector Orientation Max Standard RCF Required Support & Adapter Criteria
Fixed-Angle Rotor
Swinging-Bucket Rotor
Benchtop Micro-Centrifuge Adapter

Thermal Resilience, Freezing Protocols, and Autoclaving Rules

Medical-grade polypropylene provides thermal resilience from -80°C (or -86°C for specialized lines like Eppendorf Conical Tubes) up to +121°C. However, thermal cycling requires strict volume and pressure management.

When archiving samples at -20°C or -80°C, the expansion of water presents a major risk. Water expands by approximately 9% upon freezing. Because freezing progresses from the tube walls inward, liquid trapped in the conical apex is subjected to high pressure. If filled to 50 mL, the expanding ice column lacks headspace, leading to cracked tips or split sidewalls. Laboratories must follow the 80% fill rule: never freeze more than 40 mL of aqueous liquid in a 50 mL conical tube. Thaw frozen tubes gradually in a 37°C water bath or on wet ice, and avoid mechanical shock while frozen, as polypropylene becomes brittle below its glass transition temperature (-10°C to 0°C).

Polypropylene tubes withstand standard steam autoclaving cycles of 121°C (250°F) at 15 psi for 15 to 20 minutes. The primary failure mode during autoclaving is leaving caps tightened. As steam inside a sealed tube condenses during cooling, a strong vacuum forms. This vacuum implodes or deforms sealed polypropylene tubes. Caps must be set loosely on the threads (at least one full turn loose) or autoclaved in separate pouches to allow pressure equalization. Allow tubes to cool completely to room temperature before torquing caps.

Chemical Compatibility and Solvent Resistance of Polypropylene Labware

Polypropylene resists aqueous salts, polar solvents, and dilute acids and bases, but its aliphatic hydrocarbon structure is susceptible to halogenated hydrocarbons, aromatic compounds, and strong oxidizing agents.

Chemical compatibility at room temperature (20°C to 25°C) falls into three categories:

  • Fully Compatible: Aliphatic alcohols (100% and 70% ethanol, isopropanol, methanol), glycerol, dimethyl sulfoxide (DMSO for routine handling and freezing), dilute mineral acids (HCl ≤20%, H2SO4 ≤20%), dilute bases (NaOH ≤20%), and biological buffers (PBS, Tris-EDTA, HEPES).
  • Conditionally Compatible: Glacial acetic acid, hydrogen peroxide (≤30%), acetone, and high-concentration DMSO (>50% prolonged contact). Minor polymer swelling or softening may occur over extended storage; high-speed centrifugation should be pre-tested.
  • Incompatible: Chloroform, phenol, phenol-chloroform mixtures, dichloromethane, hexane, toluene, xylene, and concentrated fuming nitric acid. Chlorinated and aromatic solvents dissolve or craze polypropylene, causing rapid cracking and seam failure. Phenol-chloroform or TRIzol extractions must be performed in borosilicate glass or fluoropolymer (FEP) vessels.

70% to 100%

Resistant / Satisfactory

Safe for nucleic acid precipitation, cell fixation, and long-term storage.

10% to 100%

Resistant (Room Temp)

Safe for cryopreservation media; avoid prolonged high-temp incubation.

100%

Resistant / Satisfactory

Routine DNA precipitation; fully stable during maximum rated RCF centrifugation.

10% aqueous

Resistant / Satisfactory

Alkaline lysis procedures; no polymer degradation or stress cracking.

1 M to 6 M

Resistant / Satisfactory

Compatible with mineral acid neutralization and general buffer preparation.

Reagent grade (≥99%)

Unsatisfactory / Not Recommended

Aggressively dissolves PP; causes cracking and leakage; use glass or FEP vessels.

Equilibrated organic blend

Unsatisfactory / Not Recommended

Severe plastic swelling and seam rupture; incompatible with standard conical tubes.

Chemical Reagent Tested Concentration Compatibility Rating Operational Guidance for 50 mL PP Tubes
Ethanol (Ethyl Alcohol)
Dimethyl Sulfoxide (DMSO)
Isopropanol
Sodium Hydroxide (NaOH)
Hydrochloric Acid (HCl)
Chloroform
Phenol / Chloroform

Safe Laboratory Handling, Centrifugation Balancing, and Biosafety

Centrifuges store substantial kinetic energy during operation. Safe handling requires strict adherence to rotor balancing and biosafety protocols established by CDC/NIH Biosafety in Microbiological and Biomedical Laboratories (BMBL) and OSHA guidelines.

Mass balancing is critical to centrifuge safety. Because kinetic energy scales with the square of velocity, even small mass differences between opposing buckets create severe vibration at high speeds. Opposing tubes must never be balanced by eye or meniscus level; tare weights between tube brands can differ by 1 to 2 grams, and solution densities often vary. Opposing tubes and adapters must be weighed on a balance and matched to within 0.1 grams. When running an odd number of samples, prepare a balance tube filled with water or an equivalent-density fluid to maintain symmetry.

Aerosol containment is mandatory when centrifuging human clinical specimens, bloodborne pathogens, or BSL-2/3 agents. Centrifugation can generate fine infectious aerosols if a tube leaks or fractures. CDC and OSHA guidelines require sealed aerosol-containment safety cups or rotors with intact O-rings for biohazardous runs. Safety cups must be loaded, sealed, and inspected inside a certified Class II Biological Safety Cabinet (BSC). After centrifugation, transport the sealed bucket back into the BSC before opening. If a tube break occurs during a run, keep the centrifuge lid closed for at least 20 to 30 minutes to allow aerosols to settle before initiating decontamination.

Procurement Guidelines, Quality Control, and Regulatory Standards

Procurement officers and lab managers must evaluate device classifications, purity certifications, and packaging formats against experimental requirements.

In clinical workflows, 50 mL conical tubes used for human specimen collection and transport fall under FDA regulation 21 CFR 864.3250 (Specimen transport and storage container). These Class I medical devices are 510(k) exempt but subject to general controls and listing under FDA Product Codes FMH (Container, Specimen, Sterile) or NNI (Container, Specimen, Non-Sterile). Medical buyers should confirm ISO 13485 manufacturing certification and lot traceability.

Key biological purity grades include:

  • Sterility Assurance Level (SAL): Sterile tubes achieve an SAL of 10⁻³ to 10⁻⁶ via gamma irradiation or electron beam sterilization per ISO 11137 standards.
  • Pyrogen and Endotoxin Limits: For cell culture and in vitro transfection, tubes must be certified non-pyrogenic via Limulus Amebocyte Lysate (LAL) testing (USP ), maintaining endotoxin levels below 0.05 to 0.1 EU/mL to prevent macrophage activation.
  • Nuclease-Free Certification: Molecular assays (qPCR, RNA sequencing) require certified RNase-free, DNase-free, and human DNA-free consumables to protect nucleic acid integrity.

Packaging formats include bulk bags (25 to 50 tubes per bag, 500 per case) and racked tubes (25 tubes per foam or recyclable polypropylene rack). Bulk packaging offers lower unit costs for chemical preparation and student labs, while racked packaging protects graduations from abrasion, keeps tubes vertically oriented for direct freezing, and enables aseptic pickup in sterile hoods.

Common Operational Mistakes and How to Prevent Them

Preventing frequent procedural errors protects samples and centrifuge equipment:

  1. Overfilling Beyond 40 mL for Freezing: Exceeding 40 mL before -80°C storage causes expanding ice to rupture the conical bottom. Maintain at least 20% expansion headspace.
  2. Tightening Caps During Autoclaving: Sealed caps cause vacuum collapse upon cooling, warping tubes irreparably. Always leave caps loose during autoclaving.
  3. Spinning Skirted Tubes Above Speed Limits: Exceeding 8,000 × g with skirted tubes crushes the outer base skirt. Use standard conical tubes for high-speed runs.
  4. Exposing Polypropylene to Chloroform: Using PP tubes for chloroform or TRIzol phase separations causes rapid solvent crazing and leakage. Use glass or fluoropolymer vessels instead.
  5. Balancing by Volume Rather Than Mass: Leveling meniscuses by eye introduces weight disparities that induce rotor vibration and spindle wear. Weigh opposing tubes to within 0.1 g.
  6. Relying on Graduations for Critical Measurements: Printed graduation marks have an error margin of ±2% to ±5%. Use calibrated pipettes for quantitative dispensing.

Frequently asked questions

What is the maximum RCF a 50 mL conical tube can withstand?

Standard high-clarity polypropylene 50 mL conical tubes typically withstand up to 16,000 to 20,000 × g in fully supported fixed-angle rotors equipped with matching conical cavity adapters. However, in swinging-bucket rotors, the maximum safe Relative Centrifugal Force is derated to 3,000 to 3,500 × g because axial compression concentrates immense hydrostatic pressure into the conical apex. Self-standing skirted variants are generally limited to 3,000 to 8,000 × g.

Can you freeze a 50 mL conical tube at -80°C?

Yes, medical-grade polypropylene 50 mL conical tubes are stable for long-term storage in -80°C and -86°C ultra-low temperature freezers. However, users must observe the 80% fill limit rule: never freeze more than 40 mL of an aqueous solution in a 50 mL tube. Because water expands by 9% upon freezing, exceeding 40 mL eliminates expansion headspace and causes expanding ice to crack the conical bottom or rupture the sidewall.

Can you autoclave a 50 mL conical tube?

Polypropylene 50 mL conical tubes can be steam autoclaved at standard sterilization cycles of 121°C (250°F) at 15 psi for 15 to 20 minutes. Crucially, the screw cap must be left completely loose or unthreaded during autoclaving. Tightening the cap creates a rapid internal vacuum as steam condenses during cooling, which will implode and warp the tube body.

What is the difference between a conical bottom and a skirted 50 mL tube?

A standard conical tube features a smooth tapered bottom that concentrates pellets into a tight apex (<0.5 mL) and withstands high centrifugal forces (up to 20,000 × g), but requires a rack to stand upright. A skirted (self-standing) tube features an outer cylindrical ring molded around the base that allows it to stand independently on a benchtop or liquid handler deck, but this design reduces its maximum centrifugation limit to 3,000 to 8,000 × g.

Why should you never use chloroform in a 50 mL polypropylene tube?

Chloroform is a chlorinated organic solvent that aggressively attacks the aliphatic polymer chains of polypropylene. When exposed to chloroform, polypropylene rapidly swells, crazes, softens, and experiences catastrophic stress-cracking, resulting in chemical leakage into the centrifuge or workspace. For protocols requiring chloroform, phenol, or TRIzol, researchers must use borosilicate glass or fluoropolymer (FEP) centrifuge tubes.

Are printed graduations on a 50 mL conical tube accurate for analytical measurements?

No, printed or molded graduation marks on 50 mL conical tubes are designed solely for visual volume estimation, carrying an error tolerance of ±2% to ±5%. They are not calibrated volumetric instruments. Analytical dilutions, standard curve preparations, and quantitative assays must always be performed using calibrated volumetric pipettes, class A graduated cylinders, or analytical balances.

Sources

  • Corning Life Sciences. Falcon 50 mL Conical Centrifuge Tubes Technical Data Sheet & Product Specifications (Cat. Nos. 352070, 352098). Accessed 2026-11-14. https://www.corning.com/worldwide/en/products/life-sciences/products/centrifuge-tubes.html
  • Eppendorf SE. Eppendorf Conical Tubes 50 mL Specification & Operating Manual. Accessed 2026-11-14. https://www.eppendorf.com/product-catalog/tubes-and-plates/conical-tubes-15-ml-and-50-ml/
  • Thermo Fisher Scientific. Thermo Scientific Nunc 50 mL Conical Centrifuge Tubes Technical Specifications (Cat. Nos. 339652, 339653). Accessed 2026-11-14. https://www.thermofisher.com/order/catalog/product/339652
  • Greiner Bio-One. CELLSTAR 50 mL Centrifuge Tube Product Data Sheet. Accessed 2026-11-14. https://www.gbo.com/en-int/products/cell-culture/cellstar-tubes/50-ml-tubes
  • Sarstedt AG & Co. KG. Sarstedt 50 ml Conical Base & Skirted Base Centrifuge Tubes Technical Profile. Accessed 2026-11-14. https://www.sarstedt.com/en/products/laboratory/centrifugation/tubes-50-ml/
  • U.S. Food and Drug Administration (FDA). 21 CFR 864.3250 — Specimen transport and storage container (Class I, 510(k) exempt, Product Codes FMH and NNI). Accessed 2026-11-14. https://www.accessdata.fda.gov/scripts/cdrh/cfdocs/cfcfr/cfrsearch.cfm?fr=864.3250
  • Centers for Disease Control and Prevention (CDC) & National Institutes of Health (NIH). Biosafety in Microbiological and Biomedical Laboratories (BMBL), 6th Edition: Centrifugation Aerosol Containment Protocols. Accessed 2026-11-14. https://www.cdc.gov/labs/BMBL.html
  • Occupational Safety and Health Administration (OSHA). Laboratory Safety Guidance: Centrifuge Operation and Biohazard Control. Accessed 2026-11-14. https://www.osha.gov/publications/laboratory-safety

Data: Standard 50 mL Conical Centrifuge Tube Technical Specifications Across Manufacturers

Comparative technical specifications for standard laboratory 50 mL conical centrifuge tubes compiled directly from manufacturer technical data sheets and product specifications published by Corning Life Sciences, Eppendorf SE, Thermo Fisher Scientific, Greiner Bio-One, and Sarstedt AG. Compares nominal volume, outer diameter, length with cap, maximum fixed-angle RCF, maximum swinging-bucket RCF, operating temperature range, and tube body material.

Standard 50 mL Conical Centrifuge Tube Technical Specifications Across Manufacturers
Product ModelTube MaterialOuter Diameter (mm)Length with Cap (mm)Max Fixed-Angle RCF (× g)Max Swinging-Bucket RCF (× g)Min Temperature (°C)Max Temperature (°C)
Corning Falcon 50 mL High-ClarityPolypropylene30115160003000-80121
Eppendorf Conical Tube 50 mL Screw CapPolypropylene30115195003200-86100
Thermo Scientific Nunc 50 mL ConicalPolypropylene29.5116170003200-80121
Greiner Bio-One CELLSTAR 50 mL ConicalPolypropylene30115170003200-80100
Sarstedt 50 mL Standard Conical BasePolypropylene28114200003500-80121
Sarstedt 50 mL Skirted Self-Standing BasePolypropylene2811580003000-80121

Follow CASRAI

Research-administration guidance, standards updates and independent tool reviews.

Ask CASRAI · free to try

Ask about 50 mL Conical Tube: Specifications, Types & Safe Use

2 free questions a day, no account.

An AI assistant for research: funder rules, compliance, methods and publishing. It links the sources behind its answers and labels answers that come from a web search.

Answers draw on CASRAI's guides and dictionary plus the federal and funder documents we index: Federal Register, Grants.gov, Regulations.gov and UKRI.

Works on this site and inside Claude, Cursor and the AI tools you already use.

Everything CASRAI publishes — this page, the dictionary, the guides and the news — stays open to read, with no account and no card.

Referenced across the research world

University of Cambridge logoColumbia University logoCrossref logoUniversity of Edinburgh logoHarvard University logoUniversity of Oxford logoPrinceton University logoStanford School of Medicine logoUniversity College London logoORCID logoUniversity of Cambridge logoColumbia University logoCrossref logoUniversity of Edinburgh logoHarvard University logoUniversity of Oxford logoPrinceton University logoStanford School of Medicine logoUniversity College London logoORCID logo
  • University of Cambridge logo
  • Columbia University logo
  • Crossref logo
  • University of Edinburgh logo
  • Harvard University logo
  • University of Oxford logo
  • Princeton University logo
  • Stanford School of Medicine logo
  • University College London logo
  • ORCID logo

View CASRAI adoption →