Written and maintained by CASRAI Editorial Board
Published · Last updated
On this page
Short answer: A bulk-fill composite is a resin-based dental restorative designed to be light-cured in a single increment about 4 to 5 mm thick, rather than built up in thin layers. The thickness a product can cure is a laboratory result that depends on the test geometry, the exposure time and the curing light, so read the manufacturer’s instructions for use alongside any headline depth figure. This page is general product information, not medical or dental advice.
Definition and scope
A 2025 laboratory study in Materials describes the category in one sentence: some modern direct restoratives are designed for bulk photocuring in increments that are 4 to 5 mm thick. The study does not give a formal definition beyond that, and neither does US device regulation. In the Code of Federal Regulations, 21 CFR 872.3690 describes a tooth shade resin material as a device composed of materials such as bisphenol-A glycidyl methacrylate (Bis-GMA), intended to restore carious lesions or structural defects in teeth, and classifies it as Class II. The regulation text does not use the term “bulk-fill”, so a bulk-fill product is listed under the same device name as other tooth shade resins.
For composition, filler classes and curing chemistry, see the CASRAI guide to dental composite resin. This page covers only what is specific to bulk-fill: how its depth claim is produced and read.
How depth of cure is tested
The depth of cure of a resin-based composite is commonly measured with the ISO 4049 scrape test, which the 2025 study describes as follows. A specimen is made in a 4 mm diameter stainless-steel mold placed over white filter paper and light-cured. The uncured material is scraped away with a plastic spatula, the maximum length of the remaining hard cylinder is measured, and that length is divided by two. See the CASRAI entry on ISO 4049 for the standard itself.
The study compared the 4 mm mold with a 6 mm mold (10 mm deep, same white-paper set-up) for six bulk-fill composites, each cured for 10 seconds with two different curing lights. In this comparison the uncured material was removed with acetone rather than scraped, and the remaining hard length was divided by two as in the standard. All six showed significantly greater depth of cure in the 6 mm mold than in the 4 mm mold (p < 0.0001). The authors argue that the 4 mm method may underestimate depth of cure and that a larger mold may be more clinically relevant, because most cavities are larger than 4 mm across. That is one study’s argument about one test, not a change to the standard.
Test conditions that move the number
| Variable | What the 2025 study reported |
|---|---|
| Mold diameter | Greater depth of cure in a 6 mm mold than a 4 mm mold for all six materials (p < 0.0001) |
| Exposure time | The shortest result (2.6 to 3.1 mm, depending on mold and light) was for a product that, with a second product, received only half its recommended exposure time in the 10 s protocol; the authors link the two |
| Curing light | A single-peak LED light gave equal or better depth of cure than a multi-peak light |
| Whose instructions | The authors stress following the composite maker’s instructions for use, not the curing-light maker’s |
Because the study used a single protocol, treat these rows as illustrations of what a depth figure depends on, not as rankings of products or lights.
Where it matters for labs, clinics and supply decisions
A depth-of-cure figure on a data sheet only means something when read with its conditions. When reviewing a bulk-fill product’s instructions for use or technical data, the study’s variables suggest these questions to ask of the document:
- What increment thickness does the manufacturer state for the product?
- Which test method and mold size produced the depth figure?
- What exposure time does the manufacturer specify, and for which curing light?
- Does the instruction sheet name requirements for the curing unit?
- Which shade or opacity does the stated depth apply to? Shade systems are explained in the VITA shade guide.
For regulatory records, search under the device name tooth shade resin material (21 CFR 872.3690, Class II), not under “bulk-fill”. For a materials-level comparison with amalgam, see amalgam vs composite.
Common misunderstandings
“4 mm cure” is a fixed property of the material
It is a result of a method. In the 2025 study the same six materials gave different depths in 4 mm and 6 mm molds, so a figure quoted without its mold and exposure conditions cannot be compared across products.
Bulk-fill is its own regulated device class
The text of 21 CFR 872.3690 contains no separate class or definition for bulk-fill; tooth shade resin material is a Class II device under 21 CFR 872.3690.
Any curing light works the same with any composite
The study’s authors conclude that the composite manufacturer’s instructions, not the light manufacturer’s, should be followed, and the table above shows exposure and light type changed the measured depth.
Frequently asked questions
What is a bulk-fill composite?
A resin-based dental restorative designed to be light-cured in increments about 4 to 5 mm thick, as described in the 2025 Materials study cited below. No formal definition appears in the study or in 21 CFR 872.3690.
How is the depth of cure of a bulk-fill composite measured?
Commonly with the ISO 4049 scrape test: a specimen is cured in a 4 mm diameter steel mold, the uncured material is scraped away, and the length of the remaining hard cylinder is divided by two. See the section on how depth of cure is tested above.
Does mold size change the depth-of-cure result?
In the 2025 study, all six materials gave significantly greater depth of cure in a 6 mm mold than in a 4 mm mold (p < 0.0001), so a depth figure should be read together with the test method used.
Is bulk-fill composite a separate regulated device type?
The text of 21 CFR 872.3690 covers tooth shade resin material, a Class II device, and does not mention bulk-fill as a separate category.
Sources
- Gulati A, Gareau AP, Price RB. Effect of a 4 mm vs. a 6 mm Diameter Mold on the Depth of Cure of 6 Bulk-Fill Resin-Based Composites. Materials (Basel) 2025;18(11):2548. PMC12155904 (https://pmc.ncbi.nlm.nih.gov/articles/PMC12155904/). Checked 2026-10-31.
- 21 CFR 872.3690, Tooth shade resin material, US Code of Federal Regulations, Cornell LII mirror of the eCFR (https://www.law.cornell.edu/cfr/text/21/872.3690). Checked 2026-10-31.







