Written and maintained by CASRAI Editorial Board
Published · Last updated
This page describes products and general use; it is not medical advice.
On this page
Cryogenic gloves are insulated hand protection for brief handling of extremely cold items such as dry ice, ultra-low freezer contents and liquid nitrogen transfers. They are not made for dipping a hand into a cryogenic liquid. Lab staff, clinic and biorepository staff and buyers use this page to match a glove to the task, read the label correctly and avoid the usual mistakes.
What cryogenic gloves are
Cryogenic gloves (also called cryo gloves) are multi-layer insulated gloves for cold work. One manufacturer, MiTeGen, describes its cryo gloves as giving “cryogenic protection for ultra-cold applications down to -196°C (-320°F)” and lists their uses as handling dry ice, low and ultra-low temperature freezers and closed cryogenic systems (MiTeGen product page).
Who uses them: researchers and technicians who pour or transfer liquid nitrogen, staff who pull samples from -80°C or -140°C freezers, and anyone handling dry ice. They sit alongside face and eye protection, and are covered more broadly in liquid nitrogen and cryogen handling safety.
How they are built
MiTeGen describes a multi-layered construction with a thermal inner lining that wicks moisture away from the hands. The same product page says the gloves are certified to EU standards for CE Category III: EN 511 (protection against cold), EN 388 and EN 420. No performance levels are listed there, so check the levels marked on the glove itself.
Types by cuff length
MiTeGen offers its cryo gloves in four cuff lengths, and does not assign a different task to each.
| Style | Cuff reaches |
|---|---|
| Wrist | The wrist |
| Mid-arm | Part of the forearm |
| Elbow | The elbow |
| Shoulder | The shoulder |
Sizes that matter
Example size chart from MiTeGen; other makers’ charts differ.
| Size (US number) | Hand length, US | Hand length, EU |
|---|---|---|
| S (8) | 6 3/4 in | 171 mm |
| M (9) | 7 3/16 in | 182 mm |
| L (10) | 7 9/16 in | 192 mm |
| XL (11) | 8 1/16 in | 204 mm |
| XXL (12) | 8 1/16 in | 204 mm |
The chart also lists a 3XL with the same hand length (204 mm); the larger sizes differ in hand width.
How to choose
Four criteria come up in the cited guidance.
- Match the task. The University of Tennessee EHS “Cryogens” sheet (November 2023) says cryogenic gloves should be worn when pouring or transferring liquid nitrogen, and when handling dry ice and material from -80°C or -140°C freezers.
- Do not substitute heat gloves. The same sheet says not to wear gloves made for heat protection in place of cryogenic gloves.
- Choose a loose fit. The sheet says cryogenic gloves must be loose-fitting so they can be removed quickly if liquid nitrogen splashes into them or a piece of dry ice falls into them.
- Read the marked standard. Manufacturers such as MiTeGen cite EN 511 for cold protection; check the markings on the specific glove.
Safe use and handling basics
- The University of Tennessee EHS sheet lists face masks or goggles together with cryogenic gloves for pouring or transferring liquid nitrogen.
- The University of New England EHS newsletter (October 2021) advises loose-fitting thermal insulated or leather gloves, long sleeves and trousers without cuffs when handling liquid nitrogen.
- Insulated gloves “are not made to permit the hands to be put into a cryogenic liquid; they will only provide short-term protection from accidental contact with the liquid” (University of New England EHS).
- When retrieving frozen vials, note that cryovials stored in the liquid phase can explode on removal; see what a cryovial is and liquid nitrogen temperature.
Common mistakes
- Using oven or welding gloves because they are “insulated”: the University of Tennessee sheet says heat-protection gloves are not a substitute.
- Choosing a snug fit: a tight glove cannot be shaken off quickly after a splash.
- Treating them as immersion gear: MiTeGen states its gloves are not intended for immersion in liquid nitrogen or other cryogenic liquids.
- Stocking only gloves and forgetting the rest of the kit; see the core facility first aid and safety supply checklist.
FAQ
Can you dip cryogenic gloves in liquid nitrogen?
No. MiTeGen states its gloves are not intended for immersion in liquid nitrogen or other cryogenic liquids, and University of New England EHS says insulated gloves give only short-term protection from accidental contact.
Are cryogenic gloves the same as oven mitts or heat gloves?
No. University of Tennessee EHS says not to wear gloves made for heat protection in place of cryogenic gloves.
Should cryogenic gloves fit tightly?
No. They should be loose-fitting so they can be removed quickly if liquid nitrogen or dry ice gets inside (University of Tennessee EHS).
What temperature are cryogenic gloves rated for?
MiTeGen lists down to -196°C (-320°F) for its cryo gloves, for handling rather than immersion. Other products carry their own ratings.
What standards do they cite?
MiTeGen cites CE Category III with EN 511, EN 388 and EN 420.
Sources
Checked 30 October 2026.
- MiTeGen, “Cryo-Gloves” product page: https://www.mitegen.com/product/cryo-gloves/
- University of Tennessee EHS, “Cryogens” (November 2023): https://ehs.utk.edu/wp-content/uploads/2025/08/Cryogens_2023.pdf
- University of New England EHS, “Lab Chatter” Vol. 7 Issue 5 (October 2021): https://une.edu/pdfs/ehs-lab-chatter-newsletter-voume-7-issue-5-october-2021







