Skip to main content
v2026.11,986 entries · CC-BY 4.0
LAC HealthSponsored

Shop freestyle libre adhesive supplies

  • FDA registered
  • ISO 13485
  • BBB Accredited A+

Shop at LAC Health

FreeStyle Libre Adhesive: Sensor Patch and Overpatch Basics

What the FreeStyle Libre sensor adhesive is, how it differs from an overpatch, and what Abbott and Dexcom publish about adhesive materials and reinforcement.

Written and maintained by CASRAI Editorial Board

Published · Last updated

This page describes products and general use; it is not medical advice.

On this page

Short answer: the adhesive on a FreeStyle Libre sensor is a built-in patch that holds the sensor to the skin for its wear period. An overpatch (a separate adhesive cover, also called overtape) is an optional add-on, not part of the sensor. This page covers what the manufacturers publish about the built-in adhesive and its materials, so clinic staff, buyers and students can tell the two apart. Who uses it: people who wear continuous glucose monitors (CGMs), and the clinic and supply staff who support them.

What the FreeStyle Libre sensor adhesive is

A CGM sensor is worn on the body, so every system includes an adhesive patch that keeps it in place for the whole wear period. Abbott states that “the FreeStyle Libre 2 system uses the exact same adhesive patch as the FreeStyle Libre system” (Abbott support page, checked 2026-10-30). By that statement, moving from one Libre generation to the next is not a change of patch.

For how CGM readings are judged, see CGM accuracy and MARD. For a pump that carries its own adhesive pod, see what is Omnipod.

How it is built

The adhesive is part of the sensor assembly: the patch comes attached to the sensor by the manufacturer. The only construction detail Abbott publishes on these pages is what the adhesive does and does not contain, set out under materials below; no full list of layers or components is published there, so none is given here.

Types and variants: built-in patch vs overpatch

Three kinds of adhesive appear in manufacturer material. The built-in adhesive comes attached to the sensor. An overpatch or medical tape is something the wearer adds on top. Dexcom’s skin-adhesion FAQ lists an overpatch or medical tape as a reinforcement option for a sensor that is peeling, and refers readers to the user guide for official instructions (Dexcom FAQ, UK-locale page, checked 2026-10-30). Dexcom also notes that it has not tested or endorsed some of the approaches listed on that page.

Variant Where it comes from What the cited pages say
Built-in patch Attached to the sensor by the manufacturer Libre 2 uses the exact same adhesive patch as Libre (Abbott)
Overpatch or medical tape Added by the wearer on top of the sensor Listed as a reinforcement option for a peeling sensor (Dexcom)
Medical adhesive Added by the wearer Listed as another option for lifted edges (Dexcom)

What manufacturers say about adhesive materials

Abbott publishes a materials statement for its Libre sensors (Abbott FreeStyle Libre 3 provider page, checked 2026-10-30):

  • Abbott removed IBOA, a common adhesive ingredient, from all FreeStyle Libre systems sensors in 2020. This included the FreeStyle Libre 2, FreeStyle Libre 14 day and FreeStyle Libre Pro systems.
  • IBOA has never been present in the FreeStyle Libre 3 sensors (footnote: not detected at a test-method limit of detection of 0.0016 micrograms per device).
  • MBPA has never been present in any FreeStyle Libre systems sensors, verified by testing with a detection limit of 0.0079 micrograms per device.

These are the manufacturer’s own statements, attributed as such.

Comparison: what each manufacturer page states

The table lists only what the cited page states. “Not stated” means that page says nothing on the point, not that the answer is no.

Topic Abbott (Libre pages cited) Dexcom (skin-adhesion FAQ)
Built-in patch Libre 2 uses the exact same adhesive patch as Libre Not stated
Materials statement IBOA removed from all Libre sensors in 2020; never in Libre 3; MBPA never present Not stated
Overpatch or medical tape Not stated Listed as a reinforcement option for a peeling sensor
Official instructions Not stated on the cited pages Refers readers to the user guide for its systems

Choosing: what the sources state

The manufacturer pages cited here state no selection criteria for third-party overpatches, so none are given. The consistent point is that the manufacturer’s own instructions for use take priority. For supplies in this area, see diagnostic and monitoring supplies.

Handling basics

  • Follow the instructions for use that come with the specific sensor; they take priority over any general page, including this one.
  • For clinic staff stocking CGM-related items, see the diabetes clinic supply checklist.
  • For related glucose-testing consumables, see glucose blood test strips and test strip expiration.
  • Questions about an individual’s skin or glucose management go to their clinician or the manufacturer.

Common mistakes

  • Assuming an overpatch is part of the sensor, or that one brand’s guidance automatically applies to another’s system.
  • Treating a seller’s wear-time or waterproof claim for an overpatch as manufacturer information.

FAQ

What is CGM adhesive?

It is the adhesive patch that holds a continuous glucose monitor sensor to the skin for its wear period. An overpatch is a separate, optional cover applied on top.

Is FreeStyle Libre 3 adhesive different from earlier Libre sensors?

Abbott states the Libre 2 uses the exact same adhesive patch as the Libre system, and that IBOA has never been present in Libre 3 sensors. Abbott’s cited pages do not describe the Libre 3 patch beyond that.

What does Dexcom say about G6 adhesive?

Dexcom’s skin-adhesion FAQ covers adhesion for its CGM systems and directs wearers to the G6, G7, ONE and ONE+ user guides for official instructions. It does not give a G6-specific adhesive specification.

Is an overpatch part of the FreeStyle Libre sensor?

No. The built-in patch comes attached to the sensor; an overpatch or overtape is a separate optional product added by the wearer.

Sources

Follow CASRAI

Research-administration guidance, standards updates and independent tool reviews.

Ask CASRAI · free to try

Ask about FreeStyle Libre Adhesive: Sensor Patch and Overpatch Basics

2 free questions a day, no account.

An AI assistant for research: funder rules, compliance, methods and publishing. It links the sources behind its answers and labels answers that come from a web search.

Answers draw on CASRAI's guides and dictionary plus the federal and funder documents we index: Federal Register, Grants.gov, Regulations.gov and UKRI.

Works on this site and inside Claude, Cursor and the AI tools you already use.

Everything CASRAI publishes — this page, the dictionary, the guides and the news — stays open to read, with no account and no card.

Referenced across the research world

University of Cambridge logoColumbia University logoCrossref logoUniversity of Edinburgh logoHarvard University logoUniversity of Oxford logoPrinceton University logoStanford School of Medicine logoUniversity College London logoORCID logoUniversity of Cambridge logoColumbia University logoCrossref logoUniversity of Edinburgh logoHarvard University logoUniversity of Oxford logoPrinceton University logoStanford School of Medicine logoUniversity College London logoORCID logo
  • University of Cambridge logo
  • Columbia University logo
  • Crossref logo
  • University of Edinburgh logo
  • Harvard University logo
  • University of Oxford logo
  • Princeton University logo
  • Stanford School of Medicine logo
  • University College London logo
  • ORCID logo

View CASRAI adoption →