Written and maintained by CASRAI Editorial Board
Published
On this page
Short answer. A GC chromatogram is a plot of detector response (y-axis) against retention time (x-axis) from a gas chromatography run. Each peak is a compound reaching the detector; its position gives retention time, its area relates to the amount present, and the flat stretches between peaks are the baseline.
What a GC chromatogram shows
In gas chromatography a vaporised sample is carried through a column by a gas, and components leave the column at different times. The chromatogram records what the detector sees as they do. Shimadzu describes the horizontal axis as the time until a component reaches the detector and the vertical axis as signal intensity; the part with no signal is the baseline and each rise is a peak. Retention time is the time from injection to the appearance of the peak. GC is suited to compounds that can be vaporised without decomposition (Wikipedia: Gas chromatography).
The same layout appears in liquid chromatography; see the HPLC chromatogram guide for that technique.
How to interpret a GC chromatogram
Retention time: what a peak is
Retention time can be used to identify an analyte only if the method conditions are constant. A peak at the same retention time as a reference standard run under identical conditions is evidence of identity, not proof; a changed column, temperature programme or carrier gas setting moves the peaks. Factors that shape peak position and width are covered in the van Deemter equation guide, and column and gas choices in GC columns, carrier gases and detectors.
Peak area: how much is there
The area under a peak is proportional to the amount of analyte present. Quantitation then runs through a calibration curve or a relative response factor: the area of the unknown is compared with areas from standards of known amount. Reading peak height by eye is a rough guide only; the integrated area is what the calculation uses.
Baseline: what is not a peak
The baseline is the signal when nothing is eluting. A flat, quiet baseline lets small peaks be integrated reliably; a drifting or wandering one does not. The detector also matters for what you can see at all: a flame ionization detector cannot detect water or carbon dioxide (Wikipedia), so their absence from an FID trace says nothing about whether they are in the sample. See the flame ionization detector guide.
GC-MS chromatogram
A GC-MS chromatogram (also written GC/MS or GC ms chromatogram) is the same plot with a mass spectrometer as the detector. Mass spectrometry can be used to identify the analytes in a chromatogram by their mass spectrum (Wikipedia), so each peak carries a spectrum as well as a retention time. Library matching of those spectra is explained in NIST library match factors, and the two hyphenated techniques are contrasted in GC-MS vs LC-MS.
Common artefacts and what the source says to check
Agilent’s GC-MS troubleshooting article gives a blank-run approach for unexpected peaks and unstable baselines. A blank run is a GC run with no injection, and it may take a few no-inject runs to stabilise. The table below restates only what that article states.
| What you see | What the Agilent article says to consider |
|---|---|
| Unknown (ghost) peaks | A dirty liner can look like bad gas; replacing the septum, liner and O-ring is an early step. Sampling hardware (syringe, vial stripper, wash and waste vials) can also be a source. |
| Peaks in a solvent blank | The solvent is contaminated, or it is washing residue off the column or inlet. |
| Baseline wander or a large ramp | Eliminate all leaks in the gas supply first. |
| Two back-to-back blanks (condensation test): the first less stable than the second | The incoming carrier gas line or the carrier gas is contaminated. |
| Both blanks show only the same bleed | Troubleshoot column bleed; bleed can follow damage to the column from oxygen (bad gas or leaks), heat or samples. |
Treat these as starting checks, not diagnoses. For records of integration and reprocessing in regulated work, see chromatography data system audit trails.
Why use GC over HPLC?
The sourced selection point is the sample: GC is for compounds that can be vaporised without decomposition, and Wikipedia gives substances that vaporise below 300 °C as quantifiable. Compounds that cannot be vaporised intact are outside what GC is suited to. This page does not rank the two techniques; the HPLC side is in the HPLC guide.
What does GC analysis tell you?
Which components are in a mixture (by retention time, or by mass spectrum with GC-MS) and how much of each (by peak area against calibration). It does not by itself tell you about anything the detector cannot see or the column cannot elute.
Common misunderstandings
- “Same retention time means same compound.” Only under constant method conditions, and ideally confirmed by a standard or a spectrum.
- “Taller peak means more analyte.” Quantitation uses area against a calibration curve or response factor.
- “No peak means not present.” The detector may not respond (FID and water or CO2) or the compound may not elute.
- “Every peak is sample.” Blank runs exist because liners, septa, solvent, gas and column bleed also produce signals.
FAQ
What is GC in chromatography?
Gas chromatography: a vaporised sample is separated in a column by a carrier gas and the components are recorded by a detector as peaks against time.
How do I read the axes?
Time (retention time) runs along the x-axis, detector response up the y-axis; flat regions are baseline and each rise is a peak.
Is a GC-MS chromatogram different?
It uses a mass spectrometer as detector, so peaks can be identified by mass spectrum as well as retention time.
General reference information for laboratory staff; not a validated method for any specific analysis.
Sources
- Wikipedia, Gas chromatography, read 2026-11-07.
- Shimadzu, Gas chromatography fundamentals, read 2026-11-07.
- Agilent Community, Troubleshooting path for unknown ghost peaks or erratic baseline, read 2026-11-07.







