Skip to main content
v2026.11,986 entries · CC-BY 4.0

GraphPad Molarity Calculator: How to Use the QuickCalcs Tool

How to use GraphPad’s four QuickCalcs molarity calculators, with a worked example you can check by hand and a note on hydrates and purity.

Written and maintained by CASRAI Editorial Board

Published · Last updated

On this page

Who this is for: a researcher or lab member who needs the right GraphPad molarity calculator for a bench task and wants to check the result by hand. After reading you can pick the correct one of GraphPad’s four molarity calculators, enter the units it expects, and verify the answer with c = n/V.

The “GraphPad molarity calculator” (also searched as “GraphPad calculator molarity” or “molarity calculator GraphPad”) is the Molarity Calculator page in GraphPad QuickCalcs, a set of browser-based calculators from GraphPad Software (GraphPad by Dotmatics). It is a web page with four independent calculators, not a feature inside the Prism program.

What the GraphPad molarity calculator is used for in research

Molarity is moles of solute per litre of solution (mol/L). The page covers the four routine bench questions about it. GraphPad labels them as follows, and its note on the page is that “the calculators on this page are independent and can be used in any order.”

Bench task GraphPad calculator Inputs you enter Output shown
Make a stock from powder: how much to weigh Mass from volume & concentration Concentration (fM, pM, nM, µM, mM, M); Formula Weight (g/mol); Volume (µL, mL, L) Mass
You weighed a known mass: how much solvent for a target concentration Volume from mass & concentration Mass (µg, mg, g, kg); Formula Weight (g/mol); Concentration (fM to M) Volume
Check the concentration of a solution you already made Molarity from mass & volume Mass (µg, mg, g, kg); Formula Weight (g/mol); Volume (µL, mL, L) Molarity
Prepare a working dilution from a stock Dilute a stock solution Stock concentration; Desired concentration (fM to M); Desired volume (µL, mL, L) Required volume

Source: GraphPad QuickCalcs, Molarity Calculator, checked 2026-11-07.

Access: QuickCalcs, not Prism

Open the calculator in a browser at graphpad.com/quickcalcs/molarityform, or go to the QuickCalcs index at graphpad.com/quickcalcs and choose the category Chemical and radiochemical data (creating and converting molar solutions, converting between moles and grams, radioactivity calculations). GraphPad describes QuickCalcs as a way to “run statistical analyses quickly and directly in your browser.” No installation is involved, so there is nothing to find in Prism’s menus. If you are looking for an installable program, you want Prism itself, which is a separate product; see the protein molarity calculator guide for a related, protein-specific workflow.

Step-by-step: the four calculators

A worked example, using an illustrative compound with a formula weight of 250.0 g/mol (a made-up value chosen to keep the arithmetic readable). Goal: a 50 mM stock, then a working dilution.

1. Mass from volume & concentration (make a stock)

  1. Under “Mass from volume & concentration”, enter Concentration = 50, unit millimolar.
  2. Enter Formula Weight = 250.0 (grams/mole).
  3. Enter Volume = 10, unit milliliter, then run the calculation.
  4. Mass shown should be 0.125 g. Hand check: n = 0.050 mol/L × 0.010 L = 0.000500 mol; m = n × FW = 0.000500 × 250.0 = 0.125 g.

2. Volume from mass & concentration (you weighed something else)

  1. Enter the mass you actually weighed, for example 0.125 g, with its unit.
  2. Enter the Formula Weight (250.0) and the target Concentration (50 mM).
  3. Volume should be 10 mL. Hand check: n = 0.125 / 250.0 = 0.000500 mol; V = n/c = 0.000500 / 0.050 = 0.0100 L.

3. Molarity from mass & volume (verify an existing solution)

  1. Enter Mass = 0.125 g, Formula Weight = 250.0, Volume = 10 mL.
  2. Molarity should be 0.05 M (50 mM). Hand check: c = (0.125 / 250.0) / 0.010 = 0.050 mol/L.

4. Dilute a stock solution (working dilution)

  1. Enter Stock concentration = 50 mM, Desired concentration = 100 µM, Desired volume = 20 mL.
  2. Required volume of stock should be 0.04 mL (40 µL). Hand check with C1V1 = C2V2: 50 mM = 50,000 µM, so V1 = (100 × 20 mL) / 50,000 = 0.04 mL. Add that volume of stock to solvent to reach the final 20 mL total.

The calculators are independent, so the 50 mM stock from step 1 is entered by hand into step 4 as the stock concentration; nothing is carried over automatically. The same arithmetic for a percent-based stock is in the percent solution dilution calculator guide, and the units step is covered in molarity to millimoles and millimolarity to molarity. For checking a calculator result by hand, see the molarity and solution calculations guide.

Output and how to read it

  • Each calculator returns a single labelled value (Mass, Volume, Molarity or Required volume) for the unit you selected. The page does not display the formula it used, so the hand check above is the way to confirm a result.
  • Change the unit selector rather than the number when moving between mM and µM; the tool treats the unit selection as part of the input.
  • The page does not describe rounding or precision. Round the final weighing to what your balance can actually measure and record the formula weight you entered.
  • The tool has no field for hydration or purity. If the reagent is a hydrate, enter the formula weight of the hydrate as printed on the bottle label. For a stated purity below 100%, divide the calculated mass by the purity fraction yourself (for example, 0.125 g / 0.95 = 0.132 g).

Troubleshooting

  • Result off by a factor of 1,000: a unit mismatch, most often mM entered as M or mL as L. Re-check each unit selector.
  • Result does not match a published recipe: compare the formula weight. Anhydrous and hydrated forms of the same salt differ, and the calculator uses exactly the number you type. To work out a formula weight from a formula, see how to calculate molar mass.
  • Dilution volume larger than your final volume: the desired concentration is higher than the stock. Dilution only goes downward.
  • Doubt about any output: redo it with c = n/V and n = m/FW as in the worked example.

Free alternatives

Option What it does Note
Hand calculation or spreadsheet c = n/V, n = m/FW, C1V1 = C2V2 Lets you add a purity or hydrate correction, which GraphPad’s page has no field for.
Omni Calculator, Molarity Calculator Single calculator with fields for mass, molecular weight, volume and molarity (concentration). Checked 2026-11-07. Check its terms before relying on it.

FAQ

Is the GraphPad molarity calculator part of Prism?

No. It is a QuickCalcs web page, in the category Chemical and radiochemical data, and runs in the browser.

Which GraphPad calculator do I use to make a stock solution from powder?

“Mass from volume & concentration”: enter the target concentration, the formula weight and the final volume, and it returns the mass to weigh.

Does it correct for water of hydration or purity?

The page offers no such field. Use the hydrate’s formula weight from the label and adjust for purity by hand.

Can I use it for a protein?

Enter the protein’s molecular weight in g/mol as the Formula Weight. For a protein-specific walkthrough see the protein molarity calculator guide.

How do I check a result?

Recompute with n = m/FW then c = n/V, as shown in each step above.

Sources

Follow CASRAI

Research-administration guidance, standards updates and independent tool reviews.

Ask CASRAI · free to try

Ask about GraphPad Molarity Calculator: How to Use the QuickCalcs Tool

2 free questions a day, no account.

An AI assistant for research: funder rules, compliance, methods and publishing. It links the sources behind its answers and labels answers that come from a web search.

Answers draw on CASRAI's guides and dictionary plus the federal and funder documents we index: Federal Register, Grants.gov, Regulations.gov and UKRI.

Works on this site and inside Claude, Cursor and the AI tools you already use.

Everything CASRAI publishes — this page, the dictionary, the guides and the news — stays open to read, with no account and no card.

Referenced across the research world

University of Cambridge logoColumbia University logoCrossref logoUniversity of Edinburgh logoHarvard University logoUniversity of Oxford logoPrinceton University logoStanford School of Medicine logoUniversity College London logoORCID logoUniversity of Cambridge logoColumbia University logoCrossref logoUniversity of Edinburgh logoHarvard University logoUniversity of Oxford logoPrinceton University logoStanford School of Medicine logoUniversity College London logoORCID logo
  • University of Cambridge logo
  • Columbia University logo
  • Crossref logo
  • University of Edinburgh logo
  • Harvard University logo
  • University of Oxford logo
  • Princeton University logo
  • Stanford School of Medicine logo
  • University College London logo
  • ORCID logo

View CASRAI adoption →