Written and maintained by CASRAI Editorial Board
Published · Last updated
On this page
The GraphPad P value calculator is a free, browser-based tool in GraphPad’s QuickCalcs collection. You enter a test statistic (z, t, F, r or chi-square) and, where needed, its degrees of freedom, and it returns a two-tailed P value. This guide covers the exact inputs for each calculator, the rules specific to the tool, how to read the result, and free ways to reproduce it in R.
Reader task: you have a test statistic from a paper, a software printout or a hand calculation and need its P value, without installing anything.
What the GraphPad P value calculator is used for in research
QuickCalcs, according to GraphPad, “runs statistical analyses quickly and directly in your browser”. The P value calculators sit in the category Statistical distributions and interpreting P values. They convert a statistic into a P value, which is useful when a paper reports a statistic and degrees of freedom but no exact P, or when you want to check a printed P. The same category also offers the reverse conversion (from a P value back to a statistic), and tools for binomial, Poisson and Gaussian distributions, multiple-comparison correction and Bayes calculations.
Access the calculator
Use GraphPad’s own page, graphpad.com/quickcalcs/pvalue1, or reach it from the QuickCalcs index. It runs in the browser and needs no installation. The page also promotes GraphPad Prism; the calculator itself is separate from that product.
Step-by-step: get a P value from a statistic
GraphPad describes a four-step flow on the page: select a category, choose a calculator, enter data, view results.
- Open the QuickCalcs index and select the category Statistical distributions and interpreting P values, then the option to calculate P from t, z, r, F or chi-square (or open the pvalue1 page directly).
- Choose the calculator that matches your statistic (see the table below).
- Enter the statistic and, where the calculator asks for it, the degrees of freedom (DF).
- Select Compute P and read the result.
Inputs each calculator needs
| Calculator | Enter | Notes from GraphPad |
|---|---|---|
| P from z | Z | A positive or negative Z gives the same two-sided P. |
| P from t | t, DF | Two-tailed only. |
| P from F | F, DFn, DFd | Only positive values are appropriate. |
| P from r | r, DF | r must lie between -1 and 1; DF = n – 2. |
| P from chi 2 | Chi square, DF | Only positive values are appropriate. This is the chi-square P value calculator. |
Output and how to read it
The result is a P value expressed as a decimal between 0 and 1. If P falls below your pre-chosen threshold (commonly 0.05), you reject the null hypothesis; a smaller P is stronger evidence against it. GraphPad’s own page cautions that P values can be misinterpreted or p-hacked and do not replace confidence intervals or checks for outliers. A P value is not an effect size: report the estimate with its confidence interval alongside it, and see researcher degrees of freedom for how flexible analysis choices inflate apparent significance. For borderline results, read what a P value greater than 0.05 means.
One-tailed P values
GraphPad states: “This calculator only uses two-tailed P values.” Under the standard statistical convention, if you specified the direction of the effect before collecting data and the observed effect lies in that direction, the one-tailed P is half the two-tailed value. If the direction was not pre-specified, or the effect went the other way, do not halve it.
Troubleshooting
- Negative F or chi-square: these statistics cannot be negative; re-check the source value.
- r outside -1 to 1: an r value is only valid between -1 and 1. Confirm you entered r, not r squared or a t statistic.
- Wrong DF for r: use n – 2, where n is the number of paired observations.
- F needs two DF values: numerator (DFn) and denominator (DFd) are separate inputs.
- P differs from a one-tailed printout: the calculator is two-tailed only, see above.
Free alternatives: reproduce the P value in R
R’s distribution functions compute the same upper-tail probabilities. With lower.tail = FALSE they return P(X > q); with the default TRUE, P(X <= q) (R documentation for pt, read 2026-11-07). For a two-tailed t-test, the standard formula is 2 x P(T > |t|).
| GraphPad calculator | R equivalent (two-tailed) |
|---|---|
| P from z | 2 * pnorm(abs(z), lower.tail = FALSE) |
| P from t | 2 * pt(abs(t), df, lower.tail = FALSE) |
| P from chi 2 | pchisq(x, df, lower.tail = FALSE) |
| P from F | pf(f, dfn, dfd, lower.tail = FALSE) |
Chi-square and F are upper-tail tests by construction, so the upper-tail value is the P value. For critical values rather than P values, see the t distribution table of critical values, and for another GraphPad QuickCalcs tool, the GraphPad molarity calculator.
FAQ
Is there a GraphPad p value calculator for chi square?
Yes. Choose P from chi 2, enter the chi-square value and its degrees of freedom, and select Compute P. Background on the test is in chi-square test.
Does the GraphPad p value calculator work in Excel?
No. It is a web calculator and the page describes no Excel integration. To compute P values in a spreadsheet or in code, use that program’s own distribution functions, or the R equivalents above.
Is the GraphPad P value calculator one-tailed or two-tailed?
Two-tailed only, according to GraphPad.
Can I convert a P value back to a statistic?
Yes. QuickCalcs lists the reverse calculation in the same category as the P-from-statistic tools.
Sources
- GraphPad, QuickCalcs P value calculator: https://www.graphpad.com/quickcalcs/pvalue1/ (read 2026-11-07)
- GraphPad, QuickCalcs index: https://www.graphpad.com/quickcalcs/ (read 2026-11-07)
- R Documentation, The Student t Distribution: https://stat.ethz.ch/R-manual/R-devel/library/stats/html/TDist.html (read 2026-11-07)







