Written and maintained by CASRAI Editorial Board
Published · Last updated
On this page
General product information from manufacturer instructions for use (IFU), not medical advice. Your prescriber and home care provider decide how you use oxygen.
Short answer: the myAirLife manufacturer instructions say to keep excess tubing loosely coiled and out of the way, keep the total length of tubing plus cannula within the limit (57 feet in the myAirLife oxygen tubing guide), join lengths with a swivel connector, and never tie, bend or place anything on top of the tubing. The same instructions list kinked, damaged or blocked tubing as a cause of no flow.
This guide is for people who use home oxygen (and the people who help them) and want tubing that stops folding or tangling. For tubing parts, length limits and replacement, see oxygen tubing: length limits, parts and replacement; for fire and storage rules see home oxygen safety.
What you need
- Your oxygen tubing and cannula, with the total length within the limit in your product’s instructions. The myAirLife guide (UG-20024) says tubing plus cannula should not exceed 57 feet, so that enough pressure remains to deliver the prescribed oxygen.
- A swivel connector if you need to join two lengths. The Salter swivel connector IFU describes a 360 degree rotation that helps reduce tubing torque and twisting, which prevents interruption of flow.
- Backup tubing and extra oxygen supplies. The IFU advises keeping extra supplies available.
- A damp cloth and water for cleaning the outside of the tubing, nothing stronger.
Steps: how to keep oxygen tubing from kinking
- Use the shortest length that works. The IFU troubleshooting entry for kinked tubing lists “Tubing may be too long. Use shorter lengths.” Extra length is what folds underfoot.
- Route it where nothing can crush or pinch it. The IFU says not to place anything on top of the tubing that may obstruct flow, and not to put it under blankets, bedsheets or rugs.
- Coil the excess loosely. The IFU says to keep excess tubing loosely coiled and out of the way, which also prevents tripping. It names tight coiling as a cause of kinks: make sure tubing is loosely coiled so it can unravel as needed.
- Add a swivel connector where lengths join. The IFU advises swivel connectors to join tubing lengths. To attach, push and twist the tapered end into the tubing end connector and gently tug to check the fit. To remove, hold the center of the connector, twist and pull.
- Know the manufacturer flow check. The IFU describes checking for flow against the palm of the hand, or placing the nasal prongs in a small container of clean water; bubbles appear if there is oxygen flow. See also how to read an oxygen flow meter.
Kinks versus tangles
Why does oxygen tubing kink?
The IFU names two causes: the tubing is coiled too tightly, or it becomes tangled from you walking around. A kink is a sharp fold that can block flow; a tangle is loops and twists that build up as you move.
How to keep oxygen tubing from tangling
Shorten the run, keep the spare length loosely coiled so it can unravel as you move, and put a swivel connector in the line. The swivel is designed to reduce torque and twisting. The swivel IFU also warns to position tubing so the patient does not become tangled in it or strangled, and that the patient may become hypoxic if oxygen flow is interrupted.
What can go wrong
- Tying or bending the tubing. The IFU says do not kink, bend or tie your oxygen tubing.
- No flow. A listed cause is tubing that is kinked, damaged or blocked. The IFU corrective action is to inspect the tubing for kinks, occlusion, holes or damage and to make sure nothing has been placed on top of it.
- Stiff or cracked tubing. The IFU gives old tubing, or use of an alcohol-based solution or detergent, as causes. Clean the outside only with a damp cloth and water; do not use strong detergent, disinfectant, or alcohol-based or oil-based soaps, and do not immerse it. The IFUs describe no repair method: replace tubing that is stiff or damaged.
- Moisture in the line. The swivel IFU says to use a water trap if excess condensation is present; see water trap.
- Heat and flame. The IFU says to keep tubing 6 to 10 feet from open flames and heat, and not to smoke or vape. Heat is not a method of straightening tubing.
When to involve your home care provider
The IFU troubleshooting table names the backup oxygen source and the home care provider as the next steps when the system is not functioning; your prescriber and home care provider decide what applies to you. Replace tubing and swivel connectors every 3 months, or sooner if they are soiled, discolored, stiff or damaged, per the manufacturer instructions. Check your own product’s insert, because other brands can differ.
FAQ
How do I keep oxygen tubing from tangling?
Use the shortest workable length, coil the excess loosely, and add a swivel connector to join lengths. These are the IFU recommendations.
Can I tie oxygen tubing to keep it out of the way?
No. The myAirLife IFU says not to kink, bend or tie oxygen tubing. Coil the excess loosely instead.
Can oxygen tubing go under a rug or blanket?
No. The IFU says not to place tubing under blankets, bedsheets, rugs and similar items, or put anything on top of it that may obstruct flow.
How often should oxygen tubing be replaced?
The myAirLife guide says every 3 months, or sooner if it is stiff or damaged. The swivel connector IFU also gives 3 months.
How do I know if a kink is blocking my oxygen?
The IFU describes checking for flow against the palm of the hand, or placing the nasal prongs in a small container of clean water, where bubbles appear if there is oxygen flow. For what to do about a flow problem, the IFU points to the backup source and the home care provider; your prescriber and home care provider decide how you use oxygen.
Sources
- myAirLife (Salter Labs), Oxygen Tubing User Guide, UG-20024: https://connect.myairlife.com/resources/UG-20024-C1%20Oxygen%20Tubing%20User%20Guide.pdf (checked 2026-11-01).
- myAirLife (Salter Labs), Supplemental IFU: Oxygen Tubing Connectors, Swivel (840096 Rev D): https://connect.myairlife.com/resources/840096-Supplemental-IFU-Salter-Oxygen-Tubing-Connectors-Swivel-RevD.pdf (checked 2026-11-01).
Both documents are from one manufacturer; follow the instructions packed with your own product.







