Skip to main content
v2026.11,986 entries · CC-BY 4.0
LAC HealthSponsored

Shop crush resistant oxygen tubing supplies

  • FDA registered
  • ISO 13485
  • BBB Accredited A+

Shop at LAC Health

Crush-Resistant Oxygen Tubing: Star Lumen Design, Lengths and What to Check

What crush-resistant oxygen tubing and a star lumen are, the lengths and connectors one maker offers, and the IFU limits that still apply.

Written and maintained by CASRAI Editorial Board

Published · Last updated

This page describes products and general use; it is not medical advice.

On this page

Crush-resistant oxygen tubing is oxygen supply tubing whose manufacturer describes the bore as a “star lumen” and sells as “crush-resistant”. It is sold as an extension that lengthens the reach between a concentrated oxygen source and a nasal cannula or mask. Crush resistance is a manufacturer design claim, not a tested standard, so this page focuses on what the specification sheet states and what the instructions for use (IFU) still require of the user.

Who uses it: the manufacturers’ guides name home, outpatient, extended care, transport and hospital settings, so clinic, home-care and supply staff handle it as well as the people it is supplied to.

What crush-resistant oxygen tubing is

Dynarex describes its Resp-O2 oxygen supply tubing as “designed to extend a patient’s reach when accessing a concentrated oxygen source for respiratory therapy” and lists it as “crush-resistant, star lumen oxygen supply tubing” (Dynarex sell sheet R210426). Salter Labs’ myAirLife oxygen tubing user guide (UG-20024) gives the same purpose in its intended-use statement: an additional length of tubing between the oxygen source and the nasal cannula or oxygen mask, for patients with an oxygen prescription in home, outpatient, extended care, transport and hospital settings. Note that the myAirLife guide covers that manufacturer’s general tubing product, not specifically a star-lumen design.

How the star lumen is built

A conventional tube has a plain round, hollow bore. “Star lumen” is the name Dynarex gives to the inner channel of this tubing and labels on its sell sheet. The sheet does not describe the shape in text, and it does not publish a crush-force figure or a test method. This page therefore treats “crush-resistant” as a manufacturer description and makes no claim that a star lumen cannot be blocked.

Other construction details on the Dynarex materials: the tubing is PVC (product page for item 33206), is light green “designed to help improve tube visibility”, is individually wrapped, and is not made with natural rubber latex or DEHP. It has a standard connector at one end and either a standard or a universal connector at the other.

Types and lengths

One manufacturer’s range, from the Dynarex sell sheet R210426:

Length Connector options Reorder no.
7 ft (2.1 m) Standard 33200
7 ft (2.1 m) Universal 33201
14 ft (4.3 m) Standard 33202
14 ft (4.3 m) Universal 33203
21 ft (6.4 m) Standard 33204
25 ft (7.6 m) Standard 33205
30 ft (9.1 m) Standard 33206
40 ft (12.1 m) Standard 33207
50 ft (15.2 m) Standard 33208

The sheet shows the universal connector only on the 7 ft and 14 ft items. Other manufacturers’ ranges differ, so treat this table as one example, not the whole market.

Specs to read on the sheet

A spec sheet for this product class can be checked against the following items. Each row is taken from the cited Dynarex documents.

Item What the Dynarex materials state Source
Lumen design Star lumen, described as crush-resistant Sell sheet R210426
Connector at each end Standard at one end; standard or universal at the other Sell sheet R210426
Length 7 to 50 ft (2.1 to 15.2 m) in the range Sell sheet R210426
Material PVC Product page, item 33206
Latex and DEHP Not made with natural rubber latex or DEHP Sell sheet R210426; product page lists latex “No” and DEHP free “Yes”
Prescription status Listed as “Rx only” Product page, item 33206
Packaging Individually wrapped Sell sheet R210426
Instructions for use Not on the product page; look for the IFU supplied with the item Product page, item 33206

The length limit that matters most is in the IFU rather than the sell sheet: the myAirLife guide states that the total length of the oxygen tubing and nasal cannula should not exceed 57 feet, to ensure enough pressure to deliver the prescribed oxygen. Check the IFU of the tubing actually supplied, since limits can differ by product.

Safe use and replacement basics

From the myAirLife IFU (UG-20024), as one manufacturer’s instructions:

  • Do not kink, bend or tie the tubing, and do not place anything on top of it that could obstruct flow. A crush-resistant label does not remove this instruction.
  • Clean the outside with a damp cloth and water. Do not use strong detergent, disinfectant, alcohol-based or oil-based soaps, and do not immerse the tubing.
  • The guide recommends replacing tubing every 3 months, or sooner if it becomes stiff or damaged.
  • Keep tubing at least 6 to 10 feet from open flames or heat sources; no smoking or vaping, and no aerosols or flammable cleaning products near oxygen.
  • The guide lists an overfilled humidifier and a cold floor or draft as sources of moisture inside the tubing.

For home handling see how to keep oxygen tubing from kinking and tangling, water traps and oxygen concentrator humidifiers. For the similar small-bore tubing used with nebulizers, see nebulizer tubing, and for how this equipment sits in the wider category, respiratory therapy equipment.

Common mistakes

  • Treating crush resistance as permission to fold, tie or place objects on the tube; the IFU says not to.
  • Adding extension length without checking the manufacturer’s total-length limit (57 ft in the myAirLife guide).
  • Cleaning with disinfectant, alcohol or oil-based products, which the guide says not to use.
  • Keeping tubing past the recommended replacement interval or after it becomes stiff or damaged.
  • Assuming a connector type fits: confirm standard versus universal at each end on the sheet.

Frequently asked questions

What does crush-resistant mean for oxygen tubing?

It is the manufacturer’s description of a tube designed to resist being pressed flat, in these products via a star-shaped lumen. The Dynarex sell sheet gives no test method or crush-force figure, so it is a design claim, not a rated property.

What is a star lumen?

It is the term Dynarex uses for the inner channel of its Resp-O2 tubing, labelled on its sell sheet. The sheet gives no further description of the shape.

Can crush-resistant tubing still kink?

The myAirLife IFU tells users not to kink, bend or tie oxygen tubing and not to place anything on it that may obstruct flow. It makes no exception for crush-resistant designs.

How long can oxygen tubing be?

The Dynarex range runs from 7 ft to 50 ft. The myAirLife IFU says tubing plus nasal cannula should not exceed 57 feet in total; check the IFU supplied with your tubing.

What does the manufacturer say about replacement?

The myAirLife guide recommends every 3 months, or sooner if the tubing becomes stiff or damaged.

Sources

Follow CASRAI

Research-administration guidance, standards updates and independent tool reviews.

Ask CASRAI · free to try

Ask about Crush-Resistant Oxygen Tubing: Star Lumen Design, Lengths and What to Check

2 free questions a day, no account.

An AI assistant for research: funder rules, compliance, methods and publishing. It links the sources behind its answers and labels answers that come from a web search.

Answers draw on CASRAI's guides and dictionary plus the federal and funder documents we index: Federal Register, Grants.gov, Regulations.gov and UKRI.

Works on this site and inside Claude, Cursor and the AI tools you already use.

Everything CASRAI publishes — this page, the dictionary, the guides and the news — stays open to read, with no account and no card.

Referenced across the research world

University of Cambridge logoColumbia University logoCrossref logoUniversity of Edinburgh logoHarvard University logoUniversity of Oxford logoPrinceton University logoStanford School of Medicine logoUniversity College London logoORCID logoUniversity of Cambridge logoColumbia University logoCrossref logoUniversity of Edinburgh logoHarvard University logoUniversity of Oxford logoPrinceton University logoStanford School of Medicine logoUniversity College London logoORCID logo
  • University of Cambridge logo
  • Columbia University logo
  • Crossref logo
  • University of Edinburgh logo
  • Harvard University logo
  • University of Oxford logo
  • Princeton University logo
  • Stanford School of Medicine logo
  • University College London logo
  • ORCID logo

View CASRAI adoption →