Skip to main content
v2026.11,986 entries · CC-BY 4.0
LAC HealthSponsored

Shop make toilet seat higher supplies

  • FDA registered
  • ISO 13485
  • BBB Accredited A+

Shop at LAC Health

How to Make a Toilet Seat Higher: Raised Seat Types and Safe Fitting

How to raise a toilet seat with a raised seat: steps for four types, safety checks from Red Cross sheets, and how Medicare treats E0244.

Written and maintained by CASRAI Editorial Board

Published · Last updated

On this page

General product information from published instruction sheets, not medical advice. A raised toilet seat should be used as your healthcare provider instructs; both sheets quoted here say their steps are guidelines only.

To make a toilet seat higher, you fit a raised toilet seat on the bowl. It adds height so the toilet is at a more comfortable level and it is easier to sit down and get up. Which fitting steps apply depends on the type: side-clamp, front-knob, bubble-type or adjustable-height. Each type has its own securing check, and two of them need re-tightening every week.

How to raise a toilet seat: the four fitting types

A raised toilet seat is used to raise the height of a toilet to a comfortable level, making it easier to sit down and get up, according to the Canadian Red Cross instruction sheets. Models come in different heights and designs: some have adjustable clamps on either side of the bowl, others a clamp on the front, some have armrests and some do not. A toilet safety frame may be used together with a raised seat (Province of British Columbia sheet).

Type How it holds on the bowl Securing check stated in the instructions
Side-clamp Two locking clamps turned clockwise against the outside of the bowl Hand tight only, or the threads may strip; check routinely that it is securely fitted before use
Front-knob (adjustment bracket) Rear flange under the bowl rim, front adjustment knob tightened Tighten until resistance, then an extra 1/8 inch turn, by hand with no wrench; loosen and retighten once a week
Bubble-type Tall end to the rear, inner ring over the bowl opening, pushed down into the bowl Centre your weight; the seat may tip if you lean too far forward or to either side
Adjustable-height Height clamps slide over the bowl and are bolted at the chosen height All clamps at the same height; inner part of each clamp must not pivot; loosen and retighten once a week

What you need

  • The raised toilet seat and its own instruction sheet. Some models need tools to install, for example the Aquatec 900 and 90000, which the Red Cross says have separate instruction sheets.
  • A clean, dry toilet bowl.
  • Your hands only for tightening knobs and clamps. The sheets say hand tighten only, and the front-knob instructions say not to use a wrench.

Steps

How to make a toilet seat higher with a side-clamp raised seat

  1. Lift the existing toilet seat and lid, or remove them by unscrewing the two bolts and nuts, depending on the size of the toilet.
  2. Turn both clamps on the raised seat counterclockwise until they can no longer turn.
  3. With the bowl clean and dry, centre the raised seat on the bowl so it is seated securely and the lip on its front is outside the bowl, facing forward.
  4. Turn both locking clamps clockwise until hand tight. Hand tighten only, or the threads may strip.
  5. Check before every use that the seat is securely fitted.

How to raise a toilet seat with a front-knob (adjustment bracket) model

  1. Lift the seat and lid, or remove them as above.
  2. Turn the adjustment knob counterclockwise to loosen the adjustment bracket so the raised seat can fit on the bowl.
  3. Centre the seat on the clean, dry bowl with the rear flange under the bowl rim. It should sit flat on the rim with the knob at the front of the bowl.
  4. Push the seat back as far as you can by hand so the flange is firmly seated under the rim.
  5. Turn the knob clockwise until you feel resistance, then an additional 1/8 inch turn. By hand only.
  6. If the top rear of the raised seat hits the toilet seat or lid, the British Columbia sheet says the toilet seat must be removed for a proper fit.

Bubble-type raised seat

  1. Lift the toilet seat and lid.
  2. Position the raised seat with the tall end toward the rear of the toilet and the inner ring over the bowl opening.
  3. Push down on the raised seat to install it in the bowl.

Adjustable-height raised seat

  1. Lift the toilet seat and lid. Make sure all the height adjustment clamps are at the same height.
  2. Lower the raised seat so the clamps slide over the bowl. If they do not line up with the bowl, loosen the bolts where the clamps attach to the seat, reposition them and tighten the bolts firmly.
  3. To change the height, loosen the nuts and bolts on each clamp, slide it up or down, then tighten and check that the inner part of the clamp does not pivot at all.

How to use a raised toilet seat safely

  • Back up until you feel the back of your legs touch the seat. If it has armrests, reach back for them.
  • Use armrests for support only, not your full body weight. Lower yourself slowly with equal pressure on both sides.
  • To stand, push up on the armrests or seat with equal pressure and make sure you have your balance before letting go.
  • Keep your weight centred over the seat. Leaning excessively to either side could cause instability and injury.

What can go wrong

  • The seat feels loose. If it feels unstable or can be moved by hand, do not use it until it is properly secured (Red Cross).
  • Stripped threads. Over-tightening clamps can strip them. The instructions say hand tight only.
  • Bent clamps. The British Columbia sheet warns not to bend the metal clamps to make them fit the bowl.
  • Weekly drift. Front-knob and adjustable-height types are not intended for permanent installation and should be loosened and retightened once a week to keep a proper fit.
  • Wear. Check regularly that foam hand grips on armrests are secure and do not rotate, and for front-knob models check for cracks around the adjuster mechanism.
  • Cleaning damage. Clean with detergent and warm water, rinse and wipe dry. The Red Cross sheet says not to use bleach, abrasive powders, scouring pads or solvents.

Commode over the toilet, and how Medicare treats these items

Some people use a commode chair positioned over the toilet instead of a clamped seat; see what a bedside commode is. In the Medicare local coverage article for commodes (checked 2026-11-01), a raised toilet seat (HCPCS E0244) is noncovered, and a commode chair used as a raised toilet seat by positioning it over the toilet is also noncovered. For commodes E0163, E0165, E0168, E0170 and E0171 used that way, the GY modifier must be added and the KX, GA or GZ modifiers must not be used. A raised seat supported by legs on the floor is coded as a commode. Medicare Advantage and Medicaid plans can differ, so check the plan. The code-by-code detail is in commode HCPCS codes E0163 to E0175.

When to get professional help

  • If a healthcare professional has recommended a raised toilet seat, follow their instructions. The Red Cross sheet says that if they recommend it, the user should be supervised or assisted, and the British Columbia sheet recommends supervision or assistance for users with limited physical capabilities.
  • An occupational therapist can advise on equipment for daily activities; see what occupational therapy is.
  • Where height, transfers or falls are the concern, related equipment is covered in what a transfer bench is and hospital fall prevention programs.
  • If the seat will not stay secure on your bowl, stop using it and ask the supplier or a healthcare professional.

For how high a fixed toilet itself should be set in accessible design, see ADA toilet height.

FAQ

How do I make a toilet seat higher?

Fit a raised toilet seat on the bowl following the instructions for its type: side clamps tightened by hand, a front knob turned until resistance plus 1/8 inch, a bubble-type seat pushed into the bowl, or an adjustable-height seat bolted at the same height on every clamp.

How do I raise a toilet seat without tools?

Side-clamp and front-knob models are tightened by hand, and the front-knob instructions say not to use a wrench. Some models do need tools: the Red Cross notes the Aquatec 900 and 90000 have separate instruction sheets.

How often should a raised toilet seat be re-tightened?

The British Columbia sheet says knob and adjustable-height types are not intended for permanent installation and should be loosened and retightened once a week. For side-clamp models, the Red Cross sheet says to check routinely that the seat is securely fitted before use.

Does Medicare cover a raised toilet seat?

The Medicare local coverage article checked on 2026-11-01 states that a raised toilet seat (E0244) is noncovered. Other plans can differ, so ask the plan.

Sources

Follow CASRAI

Research-administration guidance, standards updates and independent tool reviews.

Ask CASRAI · free to try

Ask about How to Make a Toilet Seat Higher: Raised Seat Types and Safe Fitting

2 free questions a day, no account.

An AI assistant for research: funder rules, compliance, methods and publishing. It links the sources behind its answers and labels answers that come from a web search.

Answers draw on CASRAI's guides and dictionary plus the federal and funder documents we index: Federal Register, Grants.gov, Regulations.gov and UKRI.

Works on this site and inside Claude, Cursor and the AI tools you already use.

Everything CASRAI publishes — this page, the dictionary, the guides and the news — stays open to read, with no account and no card.

Referenced across the research world

University of Cambridge logoColumbia University logoCrossref logoUniversity of Edinburgh logoHarvard University logoUniversity of Oxford logoPrinceton University logoStanford School of Medicine logoUniversity College London logoORCID logoUniversity of Cambridge logoColumbia University logoCrossref logoUniversity of Edinburgh logoHarvard University logoUniversity of Oxford logoPrinceton University logoStanford School of Medicine logoUniversity College London logoORCID logo
  • University of Cambridge logo
  • Columbia University logo
  • Crossref logo
  • University of Edinburgh logo
  • Harvard University logo
  • University of Oxford logo
  • Princeton University logo
  • Stanford School of Medicine logo
  • University College London logo
  • ORCID logo

View CASRAI adoption →