Written and maintained by CASRAI Editorial Board
Published · Last updated
On this page
General device information, not medical advice. This page describes how a home nebulizer (UK spelling: nebuliser) is set up, run, cleaned and stored. It does not say what medicine to use, how much, or how often; those come from the prescriber. Your own device’s instructions for use (IFU) take priority over anything here.
A home nebulizer, a nebulizer machine and a “breathing treatment machine” are the same kind of device: a compressor, tubing and a medicine cup with a mouthpiece or mask. The NHLBI describes a nebulizer as “a machine that delivers a fine, steady mist of medicine through a mouthpiece or mask”. The short answer to “how do I use one at home” is: read the IFU for your exact model, use clean and correctly assembled parts, follow the prescriber’s instructions for what goes in the cup, breathe normally through the mouthpiece or mask, then clean, disinfect and dry the parts exactly as the manufacturer says.
This guide covers the home session from set-up to storage at the level of device handling. For part-by-part assembly, see how to put a nebulizer together; for background on the device, see what is a nebulizer.
What you need
- The nebulizer system: a compressor, tubing, a medicine cup, and a mouthpiece or mask.
- The IFU that came with your model. PARI’s patient page says: “Be sure to read the instructions for use that come with your nebulizer system.”
- Whatever your prescriber has prescribed for use in the nebulizer. Neither this page nor the device maker decides that for you.
- Soap, clean water and a clean lint-free cloth for aftercare, plus whatever disinfection method your IFU lists.
How a home session works
Before the session: room and parts
- Where to sit. The 2024 guideline from the COPD Foundation Nebulizer Consortium says treatments “should be administered either in an area where the air is not recirculated into the house or near an open window.”
- Clean, assembled parts. PARI’s page treats the session as starting after you have “cleaned and disinfected your nebulizer, assembled it correctly, and have attached the tubing to the compressor”.
- Clean loading. The same consortium guideline says to “adhere to aseptic principles during the medication loading process.” What goes in the cup is the prescriber’s decision.
During the session
PARI describes the session as sitting in a relaxed, upright position with the compressor on, with the mouthpiece in the mouth (or a mask covering nose and mouth) and breathing normally. It says no special technique is needed, and that the time a treatment takes varies for each person. Your care team can tell you whether your own technique is right; the NHLBI notes that proper technique matters for people with asthma, COPD or other chronic lung disease.
After the session: clean, disinfect, dry, store
Cleaning and disinfection methods, schedules and part-replacement intervals differ by model, so this page does not give them. The COPD Foundation consortium guideline says to “strictly adhere to the manufacturer’s guidelines for cleaning and disinfecting the device.” Follow the section of your own IFU, let the parts dry fully, and store them as the IFU says.
What can go wrong
- Contamination from damp or unwashed parts. Skipping the manufacturer’s cleaning and disinfection steps is the usual route, which is why the consortium guideline points to the manufacturer’s guidelines.
- Weak or no mist. Parts that are loose, worn or clogged can reduce output. Recheck assembly against the IFU, and contact the manufacturer or supplier about replacement parts.
- Wrong parts. Tubing, filters and cups from a different model may not fit or perform as designed; see nebulizer filters for what the filter does.
Who answers which question
| Question | Where the answer comes from | Source |
|---|---|---|
| How do I assemble, clean, disinfect and replace my parts? | The IFU for your exact model | PARI patient page; COPD Foundation consortium, 2024 |
| What goes in the cup? | The prescriber | PARI patient page (“prescribed medication”) |
| Where should I sit for treatment? | An area with air not recirculated into the house, or near an open window | COPD Foundation Nebulizer Consortium, 2024 |
| How do I load the medicine cleanly? | Aseptic principles | COPD Foundation Nebulizer Consortium, 2024 |
| Is my technique right? | Ask your care team | NHLBI, NIH 21-HL-8163 |
When to get professional help
Ask your prescriber, pharmacist or respiratory therapist about anything to do with the medicine, how often to treat, or whether your symptoms are changing. For the device itself, contact the manufacturer or supplier named in your IFU.
FAQ
How do I use a nebulizer at home?
Follow your model’s IFU: clean and correctly assembled parts, the prescribed medicine loaded with aseptic technique, a relaxed upright seat, and normal breathing through the mouthpiece or mask. Afterwards, clean, disinfect and dry the parts as the manufacturer directs.
Is a home nebulizer the same as a nebulizer machine or breathing treatment machine?
These phrases describe the same device. The NHLBI calls it a machine that delivers a fine mist through a mouthpiece or mask.
How should I clean it?
The consortium guideline says to strictly adhere to the manufacturer’s guidelines for cleaning and disinfecting the device, so use your own IFU.
Where should I sit?
The 2024 COPD Foundation consortium guideline says to treat in an area where the air is not recirculated into the house, or near an open window.
Sources
Date checked for all sources: 2026-11-01.
- NHLBI, NIH. How to Use a Nebulizer Fact Sheet, NIH Publication 21-HL-8163, October 2021.
- PARI. How to use a nebulizer (PARI US).
- COPD Foundation. Nebulizer Consortium press release, 15 April 2024, on the guideline published in CHEST, March 2024.







