Skip to main content
v2026.11,986 entries · CC-BY 4.0
LAC HealthSponsored

Shop profilometer supplies

  • FDA registered
  • ISO 13485
  • BBB Accredited A+

Shop at LAC Health

Profilometer: How Stylus and Optical Types Measure Roughness

How a profilometer works, stylus versus optical types, Ra and ISO 21920-2, and the NIST calibration route, from NIST and standards sources.

Written and maintained by CASRAI Editorial Board

Published · Last updated

On this page

A profilometer is an instrument that measures the shape of a surface, most often to quantify roughness, step height and waviness. Materials scientists, quality-assurance staff and metrology labs use it to turn a surface into a measured profile and a set of numbers such as Ra. This page explains how stylus and optical profilometers work, which roughness parameters and standards sit behind the readings, and how a profilometer is calibrated and traced to national standards.

What is a profilometer?

A profilometer measures a surface profile: height variation along a line (or, for areal instruments, across an area). Two families dominate. A contact (stylus) profilometer drags a fine tip across the surface and records its vertical movement. A non-contact (optical) profilometer infers height from light, using methods such as laser triangulation, confocal microscopy, coherence scanning interferometry, digital holography or focus variation (Wikipedia, “Profilometer”, read 2026-11-07).

Who uses it: materials-testing and quality-control labs, surface-finish and manufacturing inspection, and national measurement institutes that calibrate roughness standards.

How does a profilometer work?

In a stylus instrument a diamond-tipped probe is traversed over the surface while a transducer converts the tip’s vertical motion into a height signal. NIST’s reference stylus profilometer, a Form Talysurf PGI 1240, uses a 2 µm spherical diamond tip, has a vertical resolution of 0.8 nm at its 12.5 mm range, and a traverse straightness of 100 nm or better over 200 mm (NIST, “Stylus Profilometer”, read 2026-11-07). A second NIST instrument, a Talystep with an LVDT transducer, is used for step-height calibration, with an RMS Z noise of 0.29 nm over a nominal 3.5 µm range.

Optical instruments replace the tip with light, so nothing touches the specimen. According to Wikipedia’s summary, this avoids contact damage, whereas stylus instruments measure height directly and are insensitive to the surface’s reflectance or colour.

Contact versus optical profilometers

Feature Contact (stylus) Non-contact (optical)
Principle Tip follows the surface; transducer records height Light-based: laser triangulation, confocal, coherence scanning interferometry, digital holography, focus variation
Contact with specimen Yes No, so no contact damage
Reported height range About 10 nm to 1 mm Depends on the optical method
Reported tip radius and force Tip radius about 20 nm to 50 µm; force under 1 to 50 mg Not applicable
Effect of reflectance or colour Insensitive Method-dependent
Link to surface-finish standards Most surface-finish standards are written for contact profilometers Results are interpreted against those contact-based definitions

Source: Wikipedia, “Profilometer”, read 2026-11-07. The ranges are general figures for the instrument class, not a specification of any model.

Roughness parameters and the standards behind them

A profilometer outputs a profile; standards define how that profile becomes a number.

  • Ra is the average absolute deviation of the surface peaks and valleys about the mean line, as defined in ASME B46.1-2009 (NIST SRM 2074 certificate).
  • RSm, the mean spacing of profile elements, is defined in ASME B46.1-2009 and ISO 4287:1997. The NIST certificate uses the symbol D for this spacing in its sinusoidal specimen.
  • ISO 21920-2:2021 specifies terms, definitions and parameters for surface texture by the profile method. Per the standard’s public listings, it cancels and replaces ISO 4287:1997 and ISO 13565-2 and -3; a corrigendum was issued in June 2022, and EN ISO 21920-2:2022 is identical in content.
  • NIST states that its surface texture parameters follow ASME B46.1.

Practical consequence: an Ra value is meaningful only together with the measurement conditions (tip radius, cutoff, evaluation length), which the next section illustrates.

Worked example: reading a roughness standard’s certificate

NIST Standard Reference Material 2074 is a sinusoidal roughness specimen certified for Ra and wavelength D and intended as a standard for calibrating stylus instruments. The archived certificate, issued 26 February 2013, shows the conditions under which its certified values apply (NIST SRM 2074 certificate, read 2026-11-07):

  • Stylus tip radius 5 µm ± 1 µm, with a stylus force of about 4 × 10-4 N
  • Evaluation length 4.0 mm, sampled at 1 point per µm
  • Filter: 2RC with a 0.76 mm cutoff (a Gaussian filter with a 0.8 mm cutoff gives the same Ra)
  • At least 100 periods used to determine D
  • Certified values are individual to each specimen; the sample certificate shows Ra of 0.013 µm and D of 39.998 µm
  • Repeated use can slowly degrade specimens; storage is specified at 10 to 30 °C

The certification on that archived certificate expired on 30 June 2024, so it illustrates the method rather than a currently certified product. For how certified values work in general, see Standard Reference Material (SRM).

Calibration and traceability

NIST describes three traceability routes for its stylus profilometer: roughness height via a sphere of calibrated radius (a calibration ball); step height via a ball or an interferometrically calibrated step; and roughness spacing via a laser interferometer on the traverse axis. Step-height calibration uses the Talystep, with calibrated 7 nm steps. The same logic applies when a lab checks an instrument against certified reference artefacts of known value. Compare the general approach in how to calibrate a thermometer.

What affects a profilometer’s accuracy?

The sources above identify the factors that change a reported value: stylus tip radius and force, evaluation length, filter type and cutoff, sampling interval, and the number of periods measured. The NIST instruments show what a reference-grade system achieves (sub-nanometre vertical resolution), but those figures belong to that instrument and are not a guide to commercial models. Other instrument classes covered on this site, such as pH meters and the handheld XRF analyzer, likewise report results that depend on method and calibration.

How to choose between stylus and optical

Only criteria found in the sources are stated here. The standard-driven consideration is that most surface-finish standards are written for contact profilometers, so a stylus system maps directly onto those definitions. The contact-damage consideration is that optical methods do not touch the specimen. Required height range, tip radius and the reflectance of the surface are further factors listed in the comparison table above.

Safe use and handling basics

Handling guidance for the specimens used to check a profilometer comes from the NIST certificate for SRM 2074, a sinusoidal roughness specimen. It says to store the specimen in its original wooden box in a clean, dry environment at 10 to 30 degrees C. It notes that repeated use with stylus instruments can slowly degrade roughness specimens, though the specimen is expected to keep its calibration values if measurements are taken on clear, undamaged areas. It also states that the certification is nullified if the specimen is damaged, contaminated or otherwise modified. These notes apply to that NIST specimen; follow the certificate or manual supplied with your own instrument and artefacts.

Common mistakes

  • Quoting Ra without its measurement conditions. Readings such as Ra are only comparable when tip radius, cutoff and evaluation length are stated.
  • Treating reference-instrument figures as a commercial model’s accuracy. The NIST resolution and noise figures belong to NIST’s own instruments and are not a guide to commercial models.
  • Assuming optical results match contact-defined parameters. Most surface-finish standards are written for contact profilometers, so check how an optical result relates to the parameter definition before comparing the two.
  • Measuring on a damaged or contaminated specimen. Per the NIST certificate, damage or contamination nullifies the certification, so a check against that specimen no longer means what the certificate says.

Frequently asked questions

What is a profilometer?

An instrument that measures a surface’s height profile to quantify roughness, steps and waviness, using either a contact stylus or a non-contact optical method.

What is a profilometer used for?

Measuring surface texture and step height on materials and manufactured parts, checking them against surface-finish standards, and calibrating roughness specimens in metrology labs.

How much does a profilometer cost?

This page gives no price. Cost depends on the type, range and configuration, and the sources used here state no figures.

How accurate is a profilometer?

It depends on the instrument and the measurement conditions. NIST’s reference stylus profilometer reports a vertical resolution of 0.8 nm at a 12.5 mm range. Readings such as Ra are only comparable when tip radius, cutoff and evaluation length are stated.

How does a profilometer work?

A stylus profilometer traverses a diamond tip over the surface and records its vertical motion; an optical profilometer derives height from light instead, without contact.

Sources

Follow CASRAI

Research-administration guidance, standards updates and independent tool reviews.

Ask CASRAI · free to try

Ask about Profilometer: How Stylus and Optical Types Measure Roughness

2 free questions a day, no account.

An AI assistant for research: funder rules, compliance, methods and publishing. It links the sources behind its answers and labels answers that come from a web search.

Answers draw on CASRAI's guides and dictionary plus the federal and funder documents we index: Federal Register, Grants.gov, Regulations.gov and UKRI.

Works on this site and inside Claude, Cursor and the AI tools you already use.

Everything CASRAI publishes — this page, the dictionary, the guides and the news — stays open to read, with no account and no card.

Referenced across the research world

University of Cambridge logoColumbia University logoCrossref logoUniversity of Edinburgh logoHarvard University logoUniversity of Oxford logoPrinceton University logoStanford School of Medicine logoUniversity College London logoORCID logoUniversity of Cambridge logoColumbia University logoCrossref logoUniversity of Edinburgh logoHarvard University logoUniversity of Oxford logoPrinceton University logoStanford School of Medicine logoUniversity College London logoORCID logo
  • University of Cambridge logo
  • Columbia University logo
  • Crossref logo
  • University of Edinburgh logo
  • Harvard University logo
  • University of Oxford logo
  • Princeton University logo
  • Stanford School of Medicine logo
  • University College London logo
  • ORCID logo

View CASRAI adoption →