Written and maintained by CASRAI Editorial Board
Published · Last updated
On this page
Short answer
A Rochester-Péan forceps is a heavy-duty, ratcheted hemostatic clamp designed to grasp, crush, and occlude large blood vessels, vascular pedicles, and bulky tissue masses to achieve hemostasis prior to surgical ligation. Characterized by robust shanks, an interlocking box lock, and full transverse serrations extending along the entire inner jaw, it is manufactured in straight and curved patterns from 5.5 to 12 inches.
This page describes products and general use; it is not medical advice.
Definition and scope
The Rochester-Péan forceps is an essential surgical and laboratory clamping instrument utilized across human clinical surgery, veterinary medicine, vivarium procedures, and biomedical research facilities. Originating from the pioneering designs of French surgeon Jules-Émile Péan—who introduced the ratcheted hemostatic clamp to European surgery in 1868 to control intraoperative hemorrhage without constant digital pressure—the instrument was subsequently refined at the Mayo Clinic in Rochester, Minnesota. Surgeons in Rochester enlarged the jaws, widened the shanks, and reinforced the chassis to reliably occlude large vascular pedicles and thick fibrous tissue bundles in deep abdominal, gynecological, and pelvic procedures.
In modern regulatory standards, the U.S. Food and Drug Administration (FDA) classifies manual hemostatic forceps and clamps under 21 CFR § 878.4800 (Manual surgical instrument for general use). Under this regulation, general surgical clamps are assigned FDA Product Code GDJ (Clamp, Surgical, General and Plastic Surgery) and Product Code GEN (Forceps, General and Plastic Surgery). Instruments adapted for oral or maxillofacial procedures are categorized under 21 CFR § 872.4565 under Product Code EMD (Hemostat, Surgical). As Class I medical devices, manual surgical forceps are exempt from 510(k) premarket notification requirements under section 510(l) of the Federal Food, Drug, and Cosmetic Act. However, manufacturers must maintain compliance with FDA General Controls, including establishment registration, official device listing, Quality System Regulation (21 CFR Part 820 / cGMP), and Medical Device Reporting (21 CFR Part 803).
In international medical device terminology, the Global Medical Device Nomenclature (GMDN) system classifies reusable Rochester-Péan instruments under GMDN Code 62468 (Surgical soft-tissue manipulation forceps, scissors-like, reusable). Sterile disposable variants intended for single-procedure trays or ambulatory emergency packs are categorized under GMDN Code 61478 (Surgical soft-tissue manipulation forceps, scissors-like, single-use), whereas non-clinical clamps used strictly for specimen manipulation or dressing transfer fall under GMDN Code 11791. This regulatory distinction ensures clinical and laboratory purchasers obtain instruments conforming to verified metallurgical and manufacturing tolerances rather than non-certified hardware.
How it works or how it is used in practice
The mechanical operation of a Rochester-Péan forceps relies on a class-one lever mechanism comprising five integrated structural sections: the finger rings, shanks, locking ratchet, box lock hinge, and serrated clamping jaws. This configuration converts manual hand grip force into high, uniform compressive pressure across the working faces of the jaws.
To operate the instrument correctly, the surgeon or researcher places the distal phalanx of the thumb into one ring and the distal phalanx of the ring finger into the opposing ring, extending the index finger along the shanks toward the box lock to provide three-point spatial control and rotational stability. As the finger rings are compressed together, the multi-tooth ratchet near the rings interlocks. The ratchet features three to four precision-machined stepped notches that deliver graduated mechanical tension. Each successive notch locks the jaws under increasing compressive force, maintaining secure vessel occlusion without continuous muscular exertion by the operator.
A central mechanical element of the Rochester-Péan is the box lock (mortise-and-tenon) hinge. In precision surgical manufacturing, one shank passes entirely through a machined rectangular slot in the opposing shank, secured by a flush-ground cylindrical pivot pin. This interlocking geometry provides rigid lateral stability, preventing scissor-like blade slippage or yaw when high clamping pressure is applied to dense vascular pedicles. Lower-grade utility clamps often use a simple lap joint or screw pivot, which easily loosens under lateral torque, leading to misaligned jaws and uneven tissue compression.
The inner surfaces of the Rochester-Péan jaws feature continuous, precision-cut transverse (crosswise) serrations that run along the entire working length from the box lock to the rounded tip. When closed across a vascular structure, these horizontal ridges produce a crushing hemostatic effect. By compressing the vessel walls together, the serrations collapse the lumen, disrupt the endothelial lining, and activate the local clotting cascade while preventing longitudinal slippage of the vessel out of the clamp. The tips of the jaws are rounded and toothless, facilitating blunt blunt-tissue dissection along anatomical planes without puncturing adjacent organs or tearing fragile vascular walls.
Rochester-Péan forceps are produced in two primary configurations:
- Straight Jaws: Preferred for clamping vessels in superficial or easily accessible operative fields, applying traction to tough fascial planes, securing suture ligatures, or clamping laboratory tubing where direct linear alignment is desired.
- Curved Jaws: Feature a continuous arc along the working jaw. The curve allows the operator to maintain an unobstructed line of sight into deep cavities—such as the pelvic basin, retroperitoneum, or thoracic cavity—enabling ligature placement beneath or around the instrument tip without visual interference from the shanks or handles.
Types or related concepts
Hemostatic forceps encompass a wide range of specialized designs calibrated to specific tissue densities, anatomical depths, and vascular diameters. Understanding where the Rochester-Péan fits within this instrument spectrum prevents clinical and laboratory errors. A detailed medical and laboratory forceps selection guide provides practical guidance on selecting appropriate clamping instruments across research and clinical applications.
The most direct sibling of the Rochester-Péan is the Rochester-Carmalt forceps. While both instruments share a heavy-gauge frame and identical overall length ranges, the Rochester-Carmalt features longitudinal (lengthwise) striations running parallel to the jaw axis, combined with a cross-hatched grid pattern only at the distal tip. This longitudinal orientation is designed to clamp wide, fibrous vascular sheets—such as uterine and ovarian pedicles during hysterectomies and ovariohysterectomies—because the longitudinal grooves prevent broad tissue bundles from slipping laterally out of the jaws while minimizing transverse tissue shearing. In contrast, the Rochester-Péan’s transverse serrations provide aggressive, uniform transverse crushing across the full jaw surface.
Another heavy-pattern relative is the Rochester-Ochsner forceps (often called the Kocher clamp). The Rochester-Ochsner shares the heavy frame and full transverse serrations of the Rochester-Péan but incorporates sharp, interlocking 1×2 rat-tooth tips. These teeth provide aggressive mechanical traction on tough, fibrous, or slippery tissues such as muscle fascia, aponeurosis, and tendon sheaths. However, because the sharp teeth pierce tissue, the Rochester-Ochsner is contraindicated for clamping vessels where vessel wall integrity must not be lacerated, whereas the toothless Rochester-Péan provides safe, non-piercing vascular occlusion.
In contrast to the heavy Rochester family, intermediate and delicate hemostats serve finer vascular beds. Sourced distinctions between Crile and Kelly forceps show that Kelly forceps possess transverse serrations along only the distal half of their jaws, while Crile forceps feature full transverse serrations on a much lighter, more delicate chassis (typically 5.5 inches). The smallest standard hemostat, the Halsted-Mosquito forceps (3.5 to 5.0 inches), features ultra-fine pointed jaws intended strictly for pinpoint capillary or small arteriolar hemostasis in plastic surgery, pediatric procedures, and micro-dissection. For broad clinical context, an overview of surgical hemostats outlines how these instruments form a tiered spectrum of vascular control.
The table below summarizes the key anatomical distinctions, functional mechanisms, and primary indications across the hemostatic clamp family:
| Instrument Pattern | Jaw Serration Geometry | Distal Tip Design | Comparative Chassis Weight | Primary Functional Application |
|---|---|---|---|---|
| Rochester-Péan (Straight / Curved) | Full transverse serrations along entire jaw length | Blunt, rounded, toothless | Heavy-duty, thick shanks | Clamping large blood vessels, vascular pedicles, and bulky visceral tissue bundles. |
| Rochester-Carmalt | Longitudinal striations with cross-hatched distal tip | Blunt, rounded, toothless | Heavy-duty, thick shanks | Occluding broad vascular sheets and uterine pedicles; prevents lateral tissue slippage. |
| Rochester-Ochsner (Kocher) | Full transverse serrations along entire jaw length | Sharp interlocking 1×2 rat-tooth tips | Heavy-duty, thick shanks | Grasping tough fibrous fascia, tendon sheets, and tissue masses requiring aggressive traction. |
| Crile Forceps | Full transverse serrations along entire jaw length | Fine, blunt, toothless | Medium-weight, flexible shanks | Clamping intermediate subcutaneous vessels and medium vascular branches prior to ligation. |
| Kelly Forceps | Partial transverse serrations on distal half of jaw only | Fine, blunt, toothless | Medium-weight, flexible shanks | Dissecting tissue planes and clamping medium vessels; smooth proximal jaw prevents accidental crushing. |
| Halsted-Mosquito | Fine transverse serrations along entire jaw length | Delicate, pointed, toothless | Lightweight, ultra-fine shanks | Pinpoint hemostasis on delicate capillaries, ophthalmic structures, and pediatric vessels. |
In oral surgery suites, clinical teams employ specialized dental hemostatic forceps designed to navigate restricted alveolar spaces, illustrating how basic hemostatic principles adapt to confined surgical settings.
The technical dataset below compiles standardized regulatory codes, dimensional bounds, and metallurgical classifications across these primary surgical clamp families.
Where it matters for labs, clinics or supply decisions
Rochester-Péan forceps represent significant ongoing investments for surgical suites, sterile processing departments, and biomedical laboratories. Procurement and operational decisions require close attention to metallurgy, instrument grade, and reprocessing standards.
1. Surgical Suites and Clinical Departments
In hospital operating rooms and ambulatory surgery centers, Rochester-Péan forceps are standard components of major laparotomy trays, cesarean section sets, orthopedic packs, and thoracic surgery trays. The instrument is chosen whenever surgeons require rapid, definitive vascular control during deep organ resections—such as splenectomy, nephrectomy, or hepatic resection—where vessel diameters exceed 4 to 6 millimeters and lighter hemostats lack sufficient jaw width or clamping force. Curved patterns allow the operative team to maintain visibility in the deep pelvis while placing suture ligatures beneath the instrument tip.
2. Animal Research Facilities and Vivariums
In academic research institutions and veterinary medical centers, Rochester-Péan forceps are indispensable for experimental surgery on large animal models (e.g., porcine, ovine, and canine models) as well as whole-organ isolation in rodent vascular studies. In terminal perfusion procedures, researchers utilize Rochester-Péan clamps to occlude the descending aorta or clamp visceral vascular trees to direct perfusion fixatives efficiently throughout target organ systems. Strict adherence to the principles of laboratory aseptic technique ensures that research instruments undergo verified decontamination cycles equivalent to hospital surgical standards.
3. Biomedical Bench Laboratories
Beyond live-tissue manipulation, Rochester-Péan forceps serve as heavy-duty utility clamps in biochemistry, biotechnology, and analytical labs. The strong shanks and positive ratchet lock make the instrument ideal for:
- Clamping high-pressure thick-walled silicone, Tygon, or rubber fluid-transfer tubing during bioreactor harvesting without puncturing the tubing wall.
- Manipulating hot glassware, ceramic crucibles, or metallic sample racks during autoclave unloading or thermal dry-heat processing.
- Stabilizing tough tissue blocks during macro-dissection and gross specimen trimming in histology and pathology preparation benches.
4. Materials, Metallurgy, and Regulatory Standards
Procurement teams must verify that instruments comply with metallurgical standards. High-grade surgical instruments are fabricated from wrought stainless steel governed by ASTM F899-23 (Standard Specification for Wrought Stainless Steels for Surgical Instruments) and ISO 7153-1:2016 (Surgical instruments — Materials — Part 1: Metals). Quality Rochester-Péan forceps utilize martensitic stainless steels, primarily AISI 410, 420A, or 420B (UNS S42000). Martensitic alloys contain 12.0% to 14.0% chromium and 0.15% to 0.45% carbon, allowing them to undergo thermal quenching and tempering to achieve a Rockwell C hardness (HRC) of 40 to 50.
This hardness provides the yield strength and elastic resilience necessary for the shanks to flex slightly under ratchet closure without suffering permanent plastic deformation. Additionally, the alloy forms a protective passive layer of hydrated chromium oxide (Cr2O3) that resists chemical corrosion. Surface passivation must be verified through standardized testing, such as the boiling water test and copper sulfate test defined in ASTM F1089-19 (Standard Test Method for Corrosion of Surgical Instruments). Institutional buyers should avoid unbranded utility clamps manufactured from low-chromium ferritic steels; such instruments corrode rapidly, exhibit burred serrations, and lose ratchet tension after few autoclave cycles.
5. Decontamination and Reprocessing Protocols
Under the Spaulding classification system established by the Centers for Disease Control and Prevention (CDC) and the Healthcare Infection Control Practices Advisory Committee (HICPAC), surgical forceps entering sterile vascular spaces are classified as Critical Items. Critical items require terminal sterilization between uses, with saturated steam under pressure remaining the gold standard.
Reprocessing protocols governed by ANSI/AAMI ST79:2017/A4:2023 (Comprehensive guide to steam sterilization and sterility assurance in health care facilities) require strict execution:
- Point-of-Use Pre-cleaning: Remove gross blood, proteinaceous fluids, and tissue soils immediately at the procedural field using sterile water-moistened sponges. Saline solutions must never be used for soaking or holding, as chloride ions rapidly penetrate the chromium oxide passive layer, causing severe pitting corrosion and crevice attack.
- Manual and Ultrasonic Cleaning: Submerge opened forceps in a neutral-pH (pH 6.0 to 8.0) enzymatic detergent solution. Thoroughly scrub the box lock and serrations using soft-bristled nylon brushes. Metal wire brushes must never be used, as they score the passivated surface and deposit foreign ferritic particles that cause contact rust. Ultrasonic cavitation cleaning effectively removes micro-particulates trapped within the deep transverse serrations.
- Lubrication: Post-cleaning, hinged areas must be treated with a water-soluble, steam-permeable surgical instrument lubricant (“instrument milk”). Mineral oil or silicone lubricants must be avoided, as they form impermeable barriers that shield microbes from steam penetration.
- Autoclave Sterilization: Forceps must be packaged in validated pouches or rigid containers with the ratchet completely open and unlocked (or at most resting on the first ratchet notch without tension). Locking the ratchet closed during thermal expansion induces immense mechanical stress across the box lock hinge, causing metal fatigue, micro-cracking, and sterilization failure due to shielded hinge contact surfaces.
Standard validated saturated steam autoclave parameters include:
- Dynamic Air Removal (Pre-vacuum): 132°C to 135°C (270°F to 275°F) for a minimum exposure time of 4 minutes, followed by a 20-to-30-minute dry cycle.
- Gravity Displacement: 121°C (250°F) for a minimum exposure time of 30 minutes, followed by a 15-to-30-minute dry cycle.
Common misunderstandings
Several common misunderstandings regarding Rochester-Péan forceps can lead to procedural complications, tissue trauma, or premature instrument degradation:
- Misunderstanding 1: Rochester-Péan and Rochester-Carmalt forceps are functionally interchangeable. Although both belong to the heavy Rochester pattern, their serration alignments create distinct mechanical interactions. Rochester-Péan forceps feature transverse serrations designed to crush vessels and control hemorrhage across the entire jaw face. Rochester-Carmalt forceps feature longitudinal striations that prevent wide, slippery vascular pedicles from slipping laterally during ligation. Substituting a Rochester-Péan when a Carmalt is indicated can cause tissue slippage out of the tip under heavy compression.
- Misunderstanding 2: Rochester-Péan clamps are suitable for delicate peripheral vessels. Due to their heavy shanks and strong lever ratio, Rochester-Péan forceps deliver substantial crushing force. Applying a Rochester-Péan to fine peripheral vessels (such as radial, facial, or mesenteric branches) causes severe transmural crushing, destroying the vascular intima and media beyond repair and precluding primary anastomosis. Fine vessels require Crile, Kelly, or Halsted-Mosquito hemostats.
- Misunderstanding 3: Autoclaving forceps with the ratchet fully locked protects the box lock hinge. Some technicians lock forceps onto their third ratchet tooth before sterilization under the assumption that it maintains alignment. In reality, thermal expansion inside the autoclave generates severe mechanical shear stresses across the locked box lock pin, resulting in hinge binding, misalignment, and stress-corrosion cracking. Instruments must always be autoclaved open and unlocked.
- Misunderstanding 4: Surgical stainless steel is immune to corrosion. Stainless steel is corrosion-resistant, not rust-proof. Its resistance depends entirely on an intact, microscopically thin chromium oxide passive film. Exposing instruments to chlorine bleach (sodium hypochlorite), saline solutions, quaternary ammonium compounds with free chlorides, or acidic descalers rapidly strips the passive film, leading to pitting corrosion, reddish rust spotting, and frozen hinges.
- Misunderstanding 5: Rochester-Péan forceps are atraumatic instruments. Rochester-Péan forceps are intentionally traumatic, crushing clamps. They are designed for tissues and vessels that will be ligated, cauterized, or excised. They must never be applied to viable hollow organs, bowel walls, or vascular structures intended for preservation, where atraumatic vascular clamps (such as DeBakey or Cooley clamps) are required.
Frequently asked questions
What is the difference between a Rochester-Péan and a Kelly forceps?
The primary differences involve overall size, chassis mass, and serration coverage. A Rochester-Péan is a heavy-duty instrument typically measuring 6.25 to 12 inches with thick, rigid shanks and transverse serrations running the full length of the jaw. It is designed to occlude large vessels and heavy vascular pedicles. A Kelly forceps is a smaller, lighter instrument (typically 5.5 inches) with transverse serrations covering only the distal half of the jaw. The smooth proximal jaw of the Kelly allows the surgeon to dissect tissue or grasp structures without crushing tissues near the box lock.
What is the difference between Rochester-Péan and Rochester-Carmalt forceps?
Both instruments share the heavy Rochester frame, but their jaw serrations differ fundamentally. Rochester-Péan forceps feature transverse (crosswise) serrations across the entire jaw surface, delivering uniform crosswise crushing power. Rochester-Carmalt forceps feature longitudinal (lengthwise) striations along the jaws with a cross-hatched grid pattern only at the tips. The longitudinal grooves of the Carmalt prevent broad, slippery vascular pedicles—such as uterine or ovarian pedicles—from sliding laterally out of the clamp during ligation.
Why do Rochester-Péan forceps have transverse serrations?
Transverse serrations create a series of crosswise mechanical ridges that indent and compress vascular walls when the ratchet locks. This crushing action collapses the vessel lumen, disrupts the endothelial layer, and activates physiological hemostasis while preventing the vessel from slipping longitudinally along the jaw axis prior to suture ligation.
When should straight vs curved Rochester-Péan forceps be selected?
Straight Rochester-Péan forceps are chosen when clamping vessels or applying traction in superficial, easily accessible operative fields, or when using the clamp on external tubing and fixtures in laboratory settings where straight-line pull is desired. Curved Rochester-Péan forceps are selected when working in deep, confined cavities—such as the pelvis or abdomen—where the curve allows the tip to clamp deep vascular pedicles while keeping the handles and the surgeon’s hands below the visual line of sight.
How does the FDA classify and regulate Rochester-Péan forceps?
The FDA classifies manual surgical hemostats and clamps under 21 CFR § 878.4800 (Manual surgical instrument for general use) under Product Codes GDJ and GEN. They are Class I medical devices, which are exempt from 510(k) premarket notification clearance. However, manufacturers must comply with General Controls, including establishment registration, device listing, and the Quality System Regulation (21 CFR Part 820 / cGMP).
What type of stainless steel is used to manufacture Rochester-Péan forceps?
Surgical-grade Rochester-Péan forceps are manufactured from wrought martensitic stainless steels compliant with ASTM F899-23 and ISO 7153-1:2016, most commonly AISI 410, 420A, or 420B (UNS S42000). These alloys are heat-treated and tempered to a Rockwell hardness of 40 to 50 HRC, providing high tensile strength, edge retention in the serrations, and spring resilience in the shanks while resisting corrosion through a passivated chromium oxide surface layer.
Can Rochester-Péan forceps be sterilized in a standard benchtop autoclave?
Yes. Reusable surgical stainless steel Rochester-Péan forceps are fully autoclavable via saturated steam. Under ANSI/AAMI ST79 standards, they can be processed using a pre-vacuum cycle at 132°C to 135°C (270°F to 275°F) for 4 minutes with a 20-to-30-minute dry time, or a gravity displacement cycle at 121°C (250°F) for 30 minutes with a 15-to-30-minute dry time. The instrument must always be autoclaved with the ratchet unlocked to prevent metal fatigue and ensure steam penetration into the box lock.
Can Rochester-Péan forceps be used for laboratory and bench research?
Yes. Rochester-Péan forceps are frequently utilized in biomedical, vivarium, and analytical laboratories. Typical applications include clamping fluid-transfer tubing during bioreactor harvesting, manipulating hot glassware or metal components, stabilizing tissue blocks during gross histological sectioning, and performing vascular perfusion procedures in large animal research models.
Sources
- U.S. Food and Drug Administration. 21 CFR § 878.4800: Manual surgical instrument for general use. Code of Federal Regulations Title 21, Food and Drugs. Available at: https://www.accessdata.fda.gov/scripts/cdrh/cfdocs/cfcfr/cfrsearch.cfm?fr=878.4800. Accessed November 13, 2026.
- U.S. Food and Drug Administration. AccessGUDID Database: Surgical soft-tissue manipulation forceps (GMDN 62468 / 61478). National Library of Medicine. Available at: https://accessgudid.nlm.nih.gov/. Accessed November 13, 2026.
- ASTM International. ASTM F899-23: Standard Specification for Wrought Stainless Steels for Surgical Instruments. West Conshohocken, PA: ASTM International, 2023. Available at: https://www.astm.org/f0899-23.html. Accessed November 13, 2026.
- ASTM International. ASTM F1089-19: Standard Test Method for Corrosion of Surgical Instruments. West Conshohocken, PA: ASTM International, 2019. Available at: https://www.astm.org/f1089-19.html. Accessed November 13, 2026.
- International Organization for Standardization. ISO 7153-1:2016: Surgical instruments — Materials — Part 1: Metals. Geneva: ISO, 2016. Available at: https://www.iso.org/standard/64104.html. Accessed November 13, 2026.
- Centers for Disease Control and Prevention. Guideline for Disinfection and Sterilization in Healthcare Facilities (2008). Healthcare Infection Control Practices Advisory Committee (HICPAC). Available at: https://www.cdc.gov/infection-control/hcp/disinfection-sterilization/. Accessed November 13, 2026.
- Association for the Advancement of Medical Instrumentation. ANSI/AAMI ST79:2017/A4:2023: Comprehensive guide to steam sterilization and sterility assurance in health care facilities. Arlington, VA: AAMI, 2023. Available at: https://www.aami.org/standards/ansi-aami-st79. Accessed November 13, 2026.
- Sklar Instruments. Care and Handling of Surgical Instruments: Instructions for Use. West Chester, PA: Sklar Surgical Instruments. Available at: https://www.sklarcorp.com/. Accessed November 13, 2026.
Data: Surgical Hemostatic Forceps Dimensional and Regulatory Specifications Matrix
Comparative technical specifications, regulatory classifications, serration profiles, and dimension ranges for major hemostatic forceps compiled from FDA 21 CFR regulations, AccessGUDID records, and ASTM F899 standards.
Period covered: 2024/2026. Coverage: United States.
| Instrument Pattern | FDA Regulation | FDA Product Code | FDA Device Class | GMDN Preferred Term Code | Serration Pattern | Minimum Overall Length (mm) | Maximum Overall Length (mm) | Primary Tissue Target |
|---|---|---|---|---|---|---|---|---|
| Rochester-Pean Forceps | 21 CFR 878.4800 | GDJ | Class I | 62468 | Full transverse crosswise | 140 | 305 | Large blood vessels and heavy tissue pedicles |
| Rochester-Carmalt Forceps | 21 CFR 878.4800 | GDJ | Class I | 62468 | Longitudinal striations with cross-hatched tip | 160 | 203 | Thick vascular bundles and uterine/ovarian pedicles |
| Rochester-Ochsner Forceps | 21 CFR 878.4800 | GEN | Class I | 62468 | Full transverse with 1x2 interlocking teeth | 140 | 254 | Dense fibrous tissue and muscular fascia traction |
| Crile Forceps | 21 CFR 878.4800 | GDJ | Class I | 62468 | Full transverse serrations | 140 | 160 | Intermediate subcutaneous blood vessels |
| Kelly Forceps | 21 CFR 878.4800 | GDJ | Class I | 62468 | Partial transverse serrations (distal half) | 140 | 160 | Medium-sized vessels and soft tissue dissection |
| Halsted-Mosquito Forceps | 21 CFR 878.4800 | GDJ | Class I | 62468 | Fine full transverse serrations | 90 | 125 | Delicate micro-vessels and fine localized bleeding |
Sources
- FDA 21 CFR § 878.4800: Manual surgical instrument for general use (accessed 2026-11-13)
- FDA AccessGUDID Database for Hemostatic Forceps (accessed 2026-11-13)
- ASTM F899-23: Standard Specification for Wrought Stainless Steels for Surgical Instruments (accessed 2026-11-13)
Compiled by CASRAI from the sources above. Free to reuse under CC BY 4.0 with attribution.







