Skip to main content
v2026.11,986 entries · CC-BY 4.0
LAC HealthSponsored

Shop sensor calibration supplies

  • FDA registered
  • ISO 13485
  • BBB Accredited A+

Shop at LAC Health

Sensor Calibration: Principles, Standards, and Metrological Traceability

A comprehensive guide to sensor calibration principles, metrological traceability to SI standards, mathematical modeling, and ISO/IEC 17025 compliance.

Written and maintained by CASRAI Editorial Board

Published

On this page

Sensor calibration is the documented metrological process of comparing a sensor’s measurement indications against a recognized, higher-order reference standard under controlled environmental conditions, establishing the mathematical relationship between the raw transducer output and the true physical measurand while quantifying the associated measurement uncertainty. Under international standards such as JCGM 200:2012 (VIM) and ISO/IEC 17025:2017, calibration does not inherently alter or adjust the sensor hardware; rather, it characterizes systematic deviations, enabling precise correction curves, digital compensation, and unbroken traceability to International System of Units (SI) standards.

Definition and Metrological Scope

In scientific metrology and industrial instrumentation, the term “calibration” is frequently conflated with physical alignment, zero-tare operations, or instrument adjustment. However, the Joint Committee for Guides in Metrology (JCGM), in the International Vocabulary of Metrology (VIM 3rd edition, JCGM 200:2012, Clause 2.39), defines calibration as a rigorous two-step operation:

  1. First Step: Under specified conditions, the process establishes a relationship between the quantity values with measurement uncertainties provided by measurement standards and corresponding indications with associated measurement uncertainties provided by the unit under test (UUT).
  2. Second Step: It uses this documented information to establish a relation for obtaining a measurement result from an indication, expressed via a calibration function, calibration curve, correction table, or mathematical error polynomial.

Metrological standards establish vital distinctions between calibration, adjustment, and verification:

  • Calibration vs. Adjustment: Under JCGM 200:2012 Clause 3.11, adjustment is the set of operations carried out on a measuring system so that it provides intended indications corresponding to given values of a quantity to be measured. Adjusting a sensor—such as trimming a potentiometer, writing digital register offsets, or re-flashing internal lookup tables—changes the physical behavior of the device. Calibration merely measures and documents that behavior. A proper calibration captures “as-found” data prior to any physical adjustment, followed by “as-left” calibration data if adjustment occurs.
  • Calibration vs. Verification: Under JCGM 200:2012 Clause 2.44, verification provides objective evidence that a given item fulfills specified requirements, such as a manufacturer’s Maximum Permissible Error (MPE) tolerance. Calibration yields raw measurement values and quantified uncertainty budgets; verification applies a binary pass/fail decision rule against those calibrated values. A broader comparison of these lifecycle roles is detailed in CASRAI’s analysis of qualification, validation, and calibration frameworks.
  • Traceability to the SI: As formalized in NIST policy directive NIST P 5800.00 and NIST Technical Note 2156, metrological traceability is defined as the property of a measurement result whereby the result can be related to a stated reference through a documented unbroken chain of calibrations, each contributing to the stated measurement uncertainty. Traceability is fundamentally a property of the measurement data itself, rather than an inherent attribute of a physical instrument or facility.

How Sensor Calibration Operates in Practice

Modern sensors operate as transducers, converting physical phenomena (such as temperature, mechanical strain, fluid pressure, or optical irradiance) into quantifiable electrical signals. Executing a sensor calibration requires a controlled laboratory environment, stable stimulus generation, and reference standards with superior metrological performance.

The operational workflow follows a structured sequence:

  1. Environmental Stabilization: Environmental variables—including ambient temperature, relative humidity, atmospheric pressure, and electromagnetic interference—must be stabilized and logged. For instance, temperature calibrations require stirred liquid baths or dry-well calibrators exhibiting spatial temperature uniformity within ±0.01 °C to prevent thermal gradients between the reference probe and the sensor under test.
  2. As-Found Measurement Run: The sensor is evaluated across its operating range without preliminary zeroing or adjustment. Capturing the as-found condition reveals whether analytical data collected by the sensor during previous operations remained valid or suffered out-of-spec drift.
  3. Reference Comparison: The transducer is stimulated across designated calibration setpoints. Output from the sensor is recorded simultaneously with readings from a primary or secondary reference standard whose calibration traces directly to a National Metrology Institute (NMI) such as NIST, PTB, or NPL.
  4. Uncertainty Evaluation: In accordance with JCGM 100:2008 (Guide to the Expression of Uncertainty in Measurement, or GUM), the calibration laboratory calculates the combined standard uncertainty, combining Type A statistical dispersion and Type B systematic contributions (reference standard uncertainty, bath instability, sensor resolution, and lead-wire effects).
  5. Transfer Function Determination: Input-output coordinates are processed through numerical regression to calculate sensor sensitivity, zero-point offset, and non-linearity coefficients.
  6. Reporting and Labeling: In compliance with ISO/IEC 17025:2017 Clause 7.8, a calibration certificate is generated detailing the unique serial number, environmental parameters, reference standards used, numerical results with expanded uncertainty (k = 2, 95% confidence interval), and calibration status labeling.

For an expanded exploration of foundational measurement concepts, consult CASRAI’s guide to metrological calibration principles.

Calibration Methods, Transfer Functions, and Mathematical Models

Different sensor architectures require distinct mathematical models to translate raw electrical transducer outputs into accurate engineering units. To assist metrologists and laboratory personnel in selecting the appropriate methodology, the data table below compares the metrological parameters, degrees of freedom, error models, and standard requirements across primary sensor calibration techniques.

1. Single-Point Offset Calibration

Single-point calibration exposes the sensor to a single reference value, primarily to identify and correct for additive baseline drift (zero-point offset error). For example, a piezoresistive gauge pressure sensor exposed to ambient atmospheric pressure should indicate 0.0 kPa gauge. If the transducer outputs 0.12 V instead of its nominal 0.00 V zero, an offset correction (-0.12 V) is applied across the output function. Single-point checks assume that the sensor’s slope (sensitivity) remains perfectly linear and stable across its operating span. Consequently, it is suitable only for intermediate sanity checks or sensors exhibiting negligible span drift.

2. Two-Point Span and Offset Calibration

Two-point calibration establishes a linear transfer function by evaluating the sensor at two distinct reference points, typically at the lower bound (zero) and upper bound (full-scale span) of its operational range. The mathematical relationship is modeled using the standard linear equation:

y = m · x + b

Where y is the sensor’s electrical output, x is the applied physical stimulus, m is the sensitivity slope (Δy / Δx), and b is the zero-point intercept. For instance, in a 4-20 mA current-loop pressure transmitter rated from 0 to 10 bar, 0 bar corresponds to 4.00 mA and 10 bar corresponds to 20.00 mA. Two-point calibration corrects both zero shift and span multiplier errors, but cannot correct non-linear response curves across intermediate values.

3. Multi-Point Polynomial Curve Fitting (RTDs and Callendar-Van Dusen)

When sensors exhibit known physical curvature across wide measurement ranges, multi-point calibration is required. Platinum Resistance Thermometers (PRTs and RTDs like Pt100 and Pt1000) change electrical resistance with temperature. In accordance with IEC 60751 and EURAMET Calibration Guide No. 8, the resistance-temperature relationship of industrial platinum RTDs is modeled using the Callendar-Van Dusen (CVD) polynomial equations:

  • For temperatures at or above 0 °C: R(t) = R₀ · (1 + A · t + B · t²)
  • For temperatures below 0 °C: R(t) = R₀ · (1 + A · t + B · t² + C · (t – 100) · t³)

Where R(t) is resistance at temperature t in degrees Celsius, R₀ is nominal resistance at 0 °C (e.g., 100.00 Ω for Pt100), and A, B, and C are unique coefficients determined empirically by measuring resistance at multiple fixed calibration points. In precision laboratory thermometers, entering these sensor-specific CVD coefficients into a digital transmitter eliminates standard interchangeability errors, reducing measurement uncertainty from ±0.30 °C down to ±0.03 °C. For practical sensor selection between resistive and thermoelectric devices, review CASRAI’s comparative breakdown of RTD and thermocouple temperature sensors.

4. Multi-Point Non-Linear Curve Fitting (Thermistors and Steinhart-Hart)

Negative Temperature Coefficient (NTC) thermistors exhibit extreme non-linear exponential resistance changes as a function of temperature. Linear or quadratic approximations fail across spans wider than a few degrees. Metrologists apply the third-order Steinhart-Hart equation to model thermistor behavior accurately:

1 / T = A + B · ln(R) + C · (ln(R))³

Where T is thermodynamic temperature in Kelvin, R is measured resistance in ohms, and A, B, and C are unique Steinhart-Hart coefficients. Determining these three parameters requires measuring thermistor resistance at a minimum of three distinct calibration temperatures spanning the target range (for example, 0.00 °C, 25.00 °C, and 50.00 °C). Solving the resulting system of three simultaneous equations yields sensor-specific coefficients that can achieve measurement uncertainties under ±0.005 °C. The mathematical regression principles underlying these response surfaces parallel the techniques detailed in CASRAI’s guide to analytical calibration curves and linear dynamic ranges.

Where Sensor Calibration Matters for Laboratory Quality and Regulatory Compliance

Sensor accuracy forms the bedrock of experimental reproducibility, product safety, and regulatory compliance across clinical, pharmaceutical, chemical, and physical research disciplines. When sensors drift unnoticed, experimental conclusions become invalid and manufacturing batches face rejection.

Key regulatory frameworks mandate formal sensor calibration programs:

  • ISO/IEC 17025:2017 (Testing and Calibration Laboratories): Clause 6.4 requires that laboratories identify all equipment that can influence measurement results and establish a formal calibration program. Clause 6.5 mandates that measuring equipment must be calibrated when measurement accuracy or measurement uncertainty affects the validity of reported results, ensuring an unbroken metrological traceability chain to SI units.
  • FDA GLP (21 CFR Part 58) and GMP (21 CFR Part 211): Under 21 CFR 211.68 and 21 CFR 58.63, automatic, mechanical, or electronic equipment must be routinely calibrated, inspected, and checked according to a written program designed to assure proper performance. Records of calibration inspections must be maintained.
  • Cold Chain and Biorepository Monitoring: In biologics storage, ultra-low temperature (ULT) freezers operating at -80 °C and liquid nitrogen dewars at -196 °C rely on continuously logged RTD and thermocouple sensors. A calibration error of just 2 °C can breach critical glass transition thresholds for biological specimens, jeopardizing clinical trials and cellular therapies.
  • Microfluidics and Analytical Chemistry: Analytical pressure sensors in high-performance liquid chromatography (HPLC) pumps maintain column pressures up to 100 MPa. Uncalibrated pressure transducers lead to retention time shifts, inaccurate peak integration, and severe baseline drift.

Worked Example: Multi-Point Temperature Sensor Curve Fitting and Uncertainty Budget

To illustrate how sensor calibration is executed and documented in a laboratory setting, consider an industrial Pt100 resistance temperature detector calibrated against a calibrated Standard Platinum Resistance Thermometer (SPRT) in a temperature-controlled stirred liquid bath.

1. Data Collection Across Calibration Points

The UUT and the SPRT reference standard were exposed to five stabilized nominal temperature setpoints across the range of 0 °C to 100 °C. The reference temperature (T_ref), the UUT measured resistance (R_meas), the nominal expected resistance based on standard IEC 60751 tables (R_nominal), and the observed resistance deviation (ΔR = R_meas – R_nominal) were recorded as follows:

  • Point 1 (Ice Point): Reference T = 0.002 °C; Measured R = 100.084 Ω; Nominal R = 100.001 Ω; Deviation ΔR = +0.083 Ω (+0.212 °C error).
  • Point 2: Reference T = 25.010 °C; Measured R = 109.845 Ω; Nominal R = 109.739 Ω; Deviation ΔR = +0.106 Ω (+0.276 °C error).
  • Point 3: Reference T = 50.005 °C; Measured R = 119.532 Ω; Nominal R = 119.402 Ω; Deviation ΔR = +0.130 Ω (+0.344 °C error).
  • Point 4: Reference T = 75.008 °C; Measured R = 129.141 Ω; Nominal R = 128.988 Ω; Deviation ΔR = +0.153 Ω (+0.412 °C error).
  • Point 5: Reference T = 100.015 °C; Measured R = 138.672 Ω; Nominal R = 138.497 Ω; Deviation ΔR = +0.175 Ω (+0.481 °C error).

2. Least-Squares Polynomial Parameter Fit

Fitting the data to the positive-range Callendar-Van Dusen model, R(t) = R₀ · (1 + A · t + B · t²), using non-linear least squares regression yielded the sensor-specific parameters:

  • R₀: 100.084 Ω (baseline resistance at 0 °C, reflecting an initial +0.084 Ω zero offset)
  • Coefficient A: 3.912 × 10⁻³ °C⁻¹ (standard IEC 60751 nominal is 3.9083 × 10⁻³ °C⁻¹)
  • Coefficient B: -5.845 × 10⁻⁷ °C⁻² (standard IEC 60751 nominal is -5.775 × 10⁻⁷ °C⁻²)
  • Maximum Residual: 0.003 Ω across all five points, demonstrating excellent polynomial goodness-of-fit.

3. Measurement Uncertainty Budget

In accordance with JCGM 100:2008, the expanded measurement uncertainty (U) for this calibration was calculated by combining individual uncertainty components in quadrature:

  • Reference Standard Uncertainty (u_ref): 0.008 °C (from the SPRT calibration certificate, k = 2, rectangular divisor).
  • Bath Temperature Instability and Non-Uniformity (u_bath): 0.005 °C (measured across the calibration zone).
  • Digital Multimeter Readout Uncertainty (u_dmm): 0.004 °C (resistance measurement accuracy).
  • Repeatability of UUT (u_rep): 0.006 °C (standard deviation of 10 repeated observations at 50 °C).
  • Combined Standard Uncertainty (u_c): √((0.008)² + (0.005)² + (0.004)² + (0.006)²) = 0.0116 °C.
  • Expanded Uncertainty (U, k = 2, 95% confidence): U = 2 · u_c = 0.023 °C.

By loading the derived R₀, A, and B coefficients into the laboratory’s data acquisition system, the sensor’s measurement error across the 0-100 °C range was reduced from +0.481 °C to within ±0.023 °C of the true thermodynamic reference temperature.

Establishing Empirical Calibration Intervals (ILAC-G24 / OIML D 10)

A widespread compliance error among testing facilities is the adoption of arbitrary, fixed 12-month calibration intervals without ongoing data analysis. International standard ILAC-G24 / OIML D 10 (“Guidelines for the determination of calibration intervals of measuring instruments”) explicitly rejects static, unreviewed intervals, outlining defensible methods for establishing and optimizing calibration frequency based on observed sensor drift.

ILAC-G24 outlines five structured methods for reviewing calibration intervals:

  1. Automatic Adjustment (“Staircase” Method): When a sensor is calibrated at its scheduled interval, its as-found condition is assessed against tolerance limits. If all points fall well within 80% of tolerance, the interval is extended by a predetermined increment (e.g., from 12 to 18 months). If any point falls outside tolerance or near the boundary, the interval is immediately shortened (e.g., to 6 months).
  2. Control Charts: Key calibration setpoints are plotted chronologically on Shewhart control charts. The laboratory tracks the trajectory of drift over time, calculating the drift rate per operating month. This statistical trend enables metrologists to project the date when the sensor is expected to breach its Maximum Permissible Error (MPE), triggering proactive re-calibration before out-of-spec data occurs.
  3. In-Use Time (Operating Hours or Cycles): Instead of elapsed calendar time, calibration intervals are tied directly to operational stress. For example, high-temperature thermocouples undergo rapid crystal grain boundary degradation and chemical contamination at sustained temperatures above 800 °C. Calibrating after every 500 operating hours ensures accuracy regardless of calendar duration.
  4. In-Service / Intermediate Black-Box Cross-Checks: Sensitive transducers are periodically cross-checked between formal calibrations against a dedicated internal check standard (a stable standard retained exclusively for verification). If the intermediate check confirms stability within tight bounds, formal external calibration intervals can be safely extended.
  5. Population Analysis: Facilities managing fleets of identical sensors (e.g., 200 temperature loggers in an environmental monitoring network) pool as-found calibration data to model population survival curves and reliability targets (typically targeting a 95% in-tolerance probability at the re-calibration date).

For detailed implementation strategies on adjusting schedules and documenting justifications for quality audits, consult CASRAI’s dedicated guide to calibration interval determination.

Smart Transducers and Digital Calibration Protocols (IEEE 1451.4 TEDS)

In complex multi-channel sensor deployments—such as wind tunnel arrays, automotive crash testing, or automated bioreactor skids—manually transcribing calibration certificates and typing sensitivity coefficients into data acquisition software introduces substantial human error. The IEEE 1451.4 standard solves this challenge through the Transducer Electronic Data Sheet (TEDS).

A TEDS is a standardized digital memory structure stored in a small, non-volatile EEPROM (typically utilizing a 1-Wire serial memory chip) integrated directly inside the sensor housing or connector. IEEE 1451.4 defines Mixed-Mode Communication (MMC), allowing the same physical wiring to transmit traditional analog signals during measurement mode and bidirectional digital calibration data during interrogation mode.

The standard establishes a modular architectural hierarchy:

  • Basic TEDS: A mandatory, 64-bit foundational block burned into hardware that provides globally unique identification: Manufacturer ID (14 bits), Model Number (15 bits), Version Letter (2 bits), Version Number (3 bits), and Serial Number (24 bits).
  • Standard Template: Specialized data structures tailored to specific sensor physical classes (e.g., Template 25 for accelerometers and microphones, Template 33 for strain-gauge bridge transducers, and Template 36 for thermocouples). The template stores critical parameters: sensitivity, measurement units, electrical excitation requirements, input/output range bounds, and frequency response characteristics.
  • Calibration Template and User Area: Dedicated memory sections that store the most recent calibration date, calibration interval due date, calibration lab identifier, and high-order polynomial correction coefficients.

When an IEEE 1451.4-compliant sensor is connected to a compatible data acquisition system, the instrumentation interrogates the EEPROM, reads stored sensitivity coefficients, automatically configures amplifier gains, and applies digital correction. When the physical probe undergoes re-calibration in an ISO/IEC 17025 accredited laboratory, the metrologist writes updated calibration parameters directly to the onboard EEPROM, permanently binding the verified metrological data to the physical transducer hardware.

Common Misunderstandings and Metrological Pitfalls

Decades of laboratory quality audits have uncovered persistent misconceptions regarding sensor calibration. Addressing these pitfalls ensures measurement integrity and regulatory readiness:

  1. The “NIST Test Report Number” Fallacy: A widespread misconception is that having a “NIST Test Number” on a calibration certificate proves that a sensor is NIST-traceable. As explicitly clarified in NIST Technical Note 2156, NIST test report numbers are purely internal administrative tracking codes used by NIST for billing and specimen identification. NIST explicitly states that test numbers do not certify traceability and should not be used as evidence of compliance. Metrological traceability requires an unbroken documentation chain with quantified uncertainties, not an administrative number.
  2. The “NIST Certified Laboratory” Myth: Commercial calibration laboratories frequently advertise that they are “NIST Certified.” NIST does not license, certify, or approve commercial calibration laboratories. Calibration laboratory competence is accredited by third-party accreditation bodies (such as A2LA, NVLAP, ANAB, or UKAS) operating under the international mutual recognition arrangements of ILAC to the standard ISO/IEC 17025:2017.
  3. Assuming Factory Calibration Persists Indefinitely: Sensors naturally drift due to mechanical relaxation of spring elements, dielectric breakdown, thermal cycling hysteresis, chemical poisoning of sensing membranes, and electronic component aging. A manufacturer’s initial factory calibration certificate reflects performance only at the moment of manufacturing; it does not protect against shipping shock or operational degradation.
  4. Ignoring Environmental Transfer Coefficients: Calibrating a pressure sensor at an ambient temperature of 21 °C does not guarantee accurate readings when deployed in an engine compartment at 85 °C unless thermal sensitivity shift coefficients (temperature coefficient of zero and temperature coefficient of span) are calibrated and compensated.
  5. Confusing Precision with Accuracy: A digital sensor that displays six digits of resolution with high repeatability (precision) may still be offset significantly from the true physical value (poor accuracy). Calibration is the sole metrological tool that diagnoses and quantifies this systematic offset.

Frequently asked questions

What is the difference between sensor calibration and sensor adjustment?

Under international metrology standards (JCGM 200:2012 / VIM), calibration is the act of measuring and documenting a sensor’s relationship to a reference standard with associated uncertainties, without modifying the device. Adjustment is the physical or software operation that alters the sensor’s output (such as changing zero-offset registers or potentiometer trims) to match target values. In formal quality systems, calibrating a sensor captures its as-found condition; if adjustment is performed, a subsequent as-left calibration must be executed to document post-adjustment performance.

Does a calibration certificate with a NIST test number guarantee traceability?

No. NIST Technical Note 2156 explicitly states that NIST test report numbers are administrative order numbers and do not establish metrological traceability. Traceability is established only through an unbroken, documented chain of comparisons with stated measurement uncertainties connecting the sensor’s measurement results back to the SI, typically executed by an ISO/IEC 17025 accredited calibration provider.

How often should laboratory sensors undergo re-calibration?

Calibration intervals should not be left as arbitrary annual defaults. According to ILAC-G24 / OIML D 10, initial intervals established by engineering judgment and manufacturer guidance must be dynamically reviewed using empirical drift data. Facilities should employ control charts, automatic staircase adjustments, or operating-hour thresholds to ensure that sensors are re-calibrated before their systematic drift exceeds the Maximum Permissible Error (MPE).

What is the difference between calibration and verification under ISO/IEC 17025?

Calibration produces raw measurement comparison data and calculates a quantified uncertainty budget. Verification uses that calibration data to make a formal compliance decision, checking whether the sensor’s errors fall within predefined acceptance limits or manufacturer specifications. Calibration provides the metrological truth; verification determines whether that truth is acceptable for a specific application.

Sources

  • Joint Committee for Guides in Metrology (JCGM). “International Vocabulary of Metrology — Basic and General Concepts and Associated Terms (VIM)”, JCGM 200:2012 (3rd edition). BIPM, Sèvres, France. https://www.bipm.org/en/committees/jc/jcgm/publications (accessed 2026-11-16).
  • National Institute of Standards and Technology (NIST). “Metrological Traceability Frequently Asked Questions and NIST Policy”, NIST Technical Note 2156 (S. S. Bruce, A. Possolo, R. L. Watters Jr., 2021). NIST Directive P 5800.00. https://www.nist.gov/traceability (accessed 2026-11-16).
  • International Organization for Standardization / International Electrotechnical Commission. “ISO/IEC 17025:2017: General requirements for the competence of testing and calibration laboratories.” ISO, Geneva, Switzerland. https://www.iso.org/standard/66912.html (accessed 2026-11-16).
  • International Laboratory Accreditation Cooperation (ILAC) and International Organization of Legal Metrology (OIML). “Guidelines for the determination of calibration intervals of measuring instruments”, ILAC-G24:2007 / OIML D 10:2007. https://ilac.org/publications-and-resources/ilac-guidance-series/ (accessed 2026-11-16).
  • European Association of National Metrology Institutes (EURAMET). “Calibration of Temperature Block Calibrators”, EURAMET Calibration Guide No. 18 / EURAMET cg-8 (Resistance Thermometers). https://www.euramet.org/publications-media-centre/calibration-guides (accessed 2026-11-16).
  • Institute of Electrical and Electronics Engineers (IEEE). “IEEE Standard for a Smart Transducer Interface for Sensors and Actuators—Mixed-Mode Communication Protocols and Transducer Electronic Data Sheet (TEDS) Formats”, IEEE Std 1451.4-2004. https://standards.ieee.org/ieee/1451.4/3400/ (accessed 2026-11-16).

Data: Sensor Calibration Methods and Metrological Characteristics

Comparative metrological parameters of primary sensor calibration methodologies, detailing degrees of freedom, error types resolved, governing mathematical models, and ISO/IEC 17025 standard requirements compiled from BIPM VIM, NIST TN 2156, and EURAMET guides.

Period covered: 2024/2026. Coverage: International.

Sensor Calibration Methods and Metrological Characteristics
MethodDegrees of Freedom (points)Target Error ResolvedTransfer Function ModelTarget Sensor TypesISO/IEC 17025 Reference Standard Level
Single-Point Offset Calibration1Zero-point baseline shift and tare offsety = x + bPiezoresistive pressure sensors, optical photodiodes, baseline gas sensorsSecondary working standard with calibration certificate
Two-Point Span and Offset Calibration2Zero intercept shift and linear sensitivity slope errory = m * x + bLinear strain gauges, 4-20 mA current-loop transmitters, linear potentiometersReference standard with 4:1 test uncertainty ratio
Multi-Point Callendar-Van Dusen Fitting3Non-linear resistance curvature across wide temperature spansR(t) = R0 * (1 + A*t + B*t^2)Platinum resistance thermometers (Pt100, Pt1000 PRTs)Standard Platinum Resistance Thermometer (SPRT) in stirred liquid bath
Multi-Point Steinhart-Hart Fitting3High exponential non-linearity across semiconductor thermistors1/T = A + B*ln(R) + C*(ln(R))^3NTC thermistors, negative temperature coefficient temperature probesNMI-traceable primary SPRT or fixed-point temperature cells
Multi-Point Mechanical Dynamic Calibration5Frequency-dependent sensitivity, damping, and phase lagH(s) = K / (s^2/omega^2 + 2*zeta*s/omega + 1)Piezoelectric accelerometers, dynamic pressure transducers, microphonesLaser Doppler vibrometer or air-bearing back-to-back calibration shaker

Sources

Compiled by CASRAI from the sources above. Free to reuse under CC BY 4.0 with attribution.

Follow CASRAI

Research-administration guidance, standards updates and independent tool reviews.

Ask CASRAI · free to try

Ask about Sensor Calibration: Principles, Standards, and Metrological Traceability

2 free questions a day, no account.

An AI assistant for research: funder rules, compliance, methods and publishing. It links the sources behind its answers and labels answers that come from a web search.

Answers draw on CASRAI's guides and dictionary plus the federal and funder documents we index: Federal Register, Grants.gov, Regulations.gov and UKRI.

Works on this site and inside Claude, Cursor and the AI tools you already use.

Everything CASRAI publishes — this page, the dictionary, the guides and the news — stays open to read, with no account and no card.

Referenced across the research world

University of Cambridge logoColumbia University logoCrossref logoUniversity of Edinburgh logoHarvard University logoUniversity of Oxford logoPrinceton University logoStanford School of Medicine logoUniversity College London logoORCID logoUniversity of Cambridge logoColumbia University logoCrossref logoUniversity of Edinburgh logoHarvard University logoUniversity of Oxford logoPrinceton University logoStanford School of Medicine logoUniversity College London logoORCID logo
  • University of Cambridge logo
  • Columbia University logo
  • Crossref logo
  • University of Edinburgh logo
  • Harvard University logo
  • University of Oxford logo
  • Princeton University logo
  • Stanford School of Medicine logo
  • University College London logo
  • ORCID logo

View CASRAI adoption →