Skip to main content
v2026.11,986 entries · CC-BY 4.0
LAC HealthSponsored

Shop syringe driver supplies

  • FDA registered
  • ISO 13485
  • BBB Accredited A+

Shop at LAC Health

Syringe Driver: Mechanics, Types, Specs & Safety

Explore syringe drivers: mechanical lead-screw architecture, ambulatory vs bedside models, IEC 60601-2-24 accuracy specs, and MHRA safety checks.

Written and maintained by CASRAI Editorial Board

Published

This page describes products and general use; it is not medical advice.

On this page

Who uses it: Clinical nurse specialists, palliative care nurses, intensive care clinicians, biomedical equipment technicians (BMETs), and healthcare procurement specialists.

What it is

A syringe driver—also called a syringe pump or syringe infusion pump—is an electromechanical device engineered to deliver small, highly accurate volumes of liquid medication or diagnostic fluids at continuous, controlled rates. Unlike a large-volume IV infusion pump that draws solutions from flexible bags via peristaltic mechanisms, a syringe driver mechanically advances the plunger of a standard disposable syringe. The U.S. Food and Drug Administration (FDA) regulates syringe drivers under 21 CFR § 880.5725 as Class II infusion pumps (Product Code FRN), and international health systems assess them against IEC 60601-2-24.

The primary purpose of a syringe driver is administering potent drugs where therapeutic safety requires steady micro-volume delivery without rate surges. Syringe drivers serve as essential equipment across intensive care units, operating suites, and neonatal nurseries. In palliative and hospice care, compact battery-powered syringe drivers provide continuous subcutaneous infusions (CSCI) over 24-hour periods, maintaining consistent symptom control for patients unable to take oral medications.

How it works or is built

A syringe driver converts the rotational torque of an electric stepper motor into linear displacement, driving the syringe plunger forward along a calibrated axis. Key mechanical and electronic assemblies include:

  • Stepper Motor and Gearbox: The motor delivers calibrated angular steps without physical slippage. Multi-stage reduction gears permit micro-stepping, converting motor pulses into sub-micron linear advances.
  • Lead Screw and Anti-Backlash Nut: The motor rotates a threaded stainless steel lead screw. A self-adjusting anti-backlash nut travels along the threads, translating rotation into forward thrust without mechanical play.
  • Syringe Cradle and Optical Sensors: A spring clamp secures the syringe barrel in a machined cradle. Optical sensors detect barrel collar seating, diameter, and plunger flange position before delivery starts.
  • In-Line Force Transducer (Strain Gauge): A load cell behind the pusher block measures axial reaction force. As downstream flow resistance rises from line kinks or clotted access, the transducer registers the pressure rise and triggers an occlusion alarm.
  • Microprocessor Control: Dual redundant microcontrollers calculate delivery rates from syringe barrel geometry, manage display telemetry, and govern alarms per IEC 60601-1-8.

Types and variants

Syringe drivers are engineered for specific mobility profiles and clinical delivery requirements. Selecting suitable infusion supplies requires matching device mechanics to patient care settings.

Device Class Typical Setting Representative Platforms Key Differences
Ambulatory Syringe Driver Palliative and hospice care BD BodyGuard™ T, CME T34 (K050800) Handheld profile; 9V battery; locked box; 24-h delivery; acts as an ambulatory infusion pump.
Bedside Acute Syringe Pump ICU, NICU, operating suites Perfusor Space (K172831), Medfusion 4000 (K111386) Pole-mounted; AC mains/battery; 0.01 mL/h titration; DERS safety; fits a Braun infusion pump station.
Target-Controlled Infusion (TCI) Surgical anaesthesia suites Anaesthesia-specific syringe pumps Calculates pharmacokinetic models in real time to sustain target effect-site concentrations.
Laboratory Syringe Pump Microfluidics, chemical analysis Benchtop research syringe drivers Non-clinical; glass syringes; nanoliter pulseless delivery; computer control; no medical alarms.

Sizes or specifications that matter

Syringe drivers function within strict technical tolerances specified by device manufacturers and international standards:

Specification Parameter Ambulatory Driver (BD BodyGuard T / CME T34) Bedside Syringe Pump (B. Braun Perfusor Space) Governing Standard
Flow Rate Range 0.1 to 650 mL/h (0.1 increments) 0.01 to 1,800 mL/h (0.01 increments) Manufacturer IFU / 510(k) clearances
Flow Accuracy ±5% mechanical delivery tolerance ±2% system accuracy (better than ±0.5% drive) IEC 60601-2-24 Section 201.12.1.101
Syringe Sizes 2 mL to 50 mL luer-lock syringes 2 mL to 50/60 mL disposable syringes Validated profiles (BD, Terumo, Braun)
Occlusion Pressure 200 to 1,500 mmHg configurable 9 selectable limits (0.1 to 1.2 bar) IEC 60601-2-24 Section 201.12.4.4.104
Bolus Delivery Rate 1 to 650 mL/h (bolus 0 to 20 mL) Up to 1,800 mL/h (±2% bolus accuracy) Manufacturer operator manual
Power Source 9V alkaline battery (6LR61) 100–240 V AC; rechargeable internal pack IEC 60601-1 electrical safety
Dimensions and Weight 167 × 68 × 39 mm; 230 g 249 × 68 × 152 mm; 1.4 kg Manufacturer datasheet

How to choose

Selecting an appropriate syringe driver involves evaluating delivery resolution, patient mobility, and institutional safety infrastructure. Sourced criteria include:

Selection Criterion Ambulatory Driver Requirements Bedside Acute Pump Requirements Sourced Guidance
Flow Resolution 0.1 mL/h for continuous subcutaneous infusions 0.01 mL/h for neonatal vasoactive titration ICU/NICU infusion standards
Mobility Profile Weight ≤ 250 g, battery-powered, wearable holster Pole-mountable, stackable bedside modular racks Biomedical engineering standards
Tamper Protection Lockable transparent box with key or code Keypad PIN lockouts and locking pole brackets NHS Continuous Subcutaneous Infusion policy
Dose Error Reduction (DERS) Fixed duration programs; manual dual checks Smart libraries with hard and soft dosing limits ISMP / smart pump drug library governance
Brand Recognition Optical sensor calibrated to standard brands (BD, Terumo) Multi-brand library in biomedical menus Hospital supply chain standards

For an expanded comparison across infusion hardware categories, consult our guide to infusion supplies and pump selection.

Safe use and handling basics

Syringe drivers require standardized handling protocols to ensure therapeutic accuracy and avoid line complications. Core safety practices from the UK MHRA, FDA safety alerts, and manufacturer instructions include:

  • Pre-Use Inspection: Under MHRA Safety Alert MDA/2020/007, inspect casing and lead screw before use. If white plastic wear particles are visible on the threads, remove the pump from service immediately.
  • Battery Fitment: In ambulatory units powered by 9V alkaline batteries, use only manufacturer-specified 6LR61 batteries to prevent terminal contact loss. Verify battery life on the display before starting infusion.
  • Line Priming: Connect the dedicated luer-lock infusion set or micro-bore line to the syringe and prime manually before seating the syringe in the driver. Never purge or prime tubing while connected to the patient.
  • Three-Point Syringe Seating: Place the syringe in the cradle so the barrel collar fits securely in the central slot, the barrel clamp arm rests flat against the syringe body, and the drive pusher grips the plunger flange. Confirm that the display indicates the correct syringe brand and volume.
  • Post-Occlusion Bolus Reduction: When an occlusion occurs, fluid compression stores energy. The motor reverses the lead screw upon alarm activation to depressurize the line and prevent bolus surge when released.
  • Lockbox Housing: In ambulatory care, operate the driver inside its lockbox to protect against mechanical impact, accidental plunger movement, and light exposure.

Common mistakes

  • Mismatched Syringe Brand Selection: Internal barrel dimensions vary between manufacturers (such as BD Plastipak vs. Terumo). Confirming an incorrect brand causes the driver to calculate linear travel erroneously.
  • Ignoring Lead Screw Debris: Overlooking white plastic debris on the lead screw allows mechanical wear to proceed unchecked, leading to motor stalling or under-infusion without an alarm.
  • Using Slip-Tip Syringes: Syringe drivers create substantial mechanical thrust. Friction slip-tip fittings risk line disconnection and fluid leakage; only threaded luer-lock connections should be used.
  • Overlooking Hydrostatic Elevation Effects: Changing bedside pump elevation relative to vascular access shifts hydrostatic pressure, causing transient flow fluctuations.
  • Operating Ambulatory Units Outside Lockboxes: Unhoused ambulatory pumps leave plungers and keypad buttons exposed to accidental impacts or unauthorized adjustment.

FAQ

What is a syringe driver?

A syringe driver is an electromechanical medical device that uses a motorized lead screw to advance a syringe plunger at a calibrated rate, delivering continuous micro-volume infusions of medication with high volumetric accuracy.

How does a syringe driver differ from an IV infusion pump?

While an IV infusion pump delivers fluids from flexible bags via peristaltic mechanisms up to 1,000 mL/h, a syringe driver dispenses small volumes (2 mL to 50 mL) from a rigid syringe barrel with tighter low-flow precision.

Why are syringe drivers commonly used in palliative care?

Ambulatory syringe drivers provide continuous subcutaneous infusions over 24 hours, maintaining steady symptom relief without requiring venous access or repeated injections in patients unable to take oral medication.

What does an occlusion alarm on a syringe driver mean?

An occlusion alarm indicates that the force transducer detected excessive resistance from a kinked line or clotted cannula. The pump pauses delivery and reverses the lead screw slightly to depressurize the line.

Sources

  • U.S. Food and Drug Administration (FDA). 21 CFR § 880.5725: Infusion Pump (Product Code FRN, Class II). openFDA Device Classification Database (read 2026-11-12). https://api.fda.gov/device/classification.json?search=product_code:FRN
  • U.S. Food and Drug Administration (FDA). 510(k) Clearances K050800 (CME NIKI T34 and BodyGuard T34), K172831 (Perfusor Space), and K111386 (Medfusion Model 4000). openFDA 510(k) Database (read 2026-11-12). https://api.fda.gov/device/510k.json
  • UK Medicines and Healthcare products Regulatory Agency (MHRA). Medical Device Alert MDA/2020/007: CME T34 and BD BodyGuard T Ambulatory Syringe Drivers. GOV.UK Alerts (read 2026-11-12). https://www.gov.uk/drug-device-alerts
  • International Electrotechnical Commission (IEC). IEC 60601-2-24: Particular requirements for the basic safety and essential performance of infusion pumps and controllers. IEC Standards Catalogue (read 2026-11-12). https://www.iec.ch
  • B. Braun Melsungen AG / B. Braun Medical Inc. Perfusor® Space Syringe Infusion Pump System Instructions for Use. B. Braun Medical Technical Library (read 2026-11-12). https://www.bbraun.com
  • Becton, Dickinson and Company (BD) / Caesarea Medical Electronics (CME). BD BodyGuard™ T Syringe Pump Operator’s Manual. BD Medication Management Systems (read 2026-11-12). https://www.bd.com

Follow CASRAI

Research-administration guidance, standards updates and independent tool reviews.

Ask CASRAI · free to try

Ask about Syringe Driver: Mechanics, Types, Specs & Safety

2 free questions a day, no account.

An AI assistant for research: funder rules, compliance, methods and publishing. It links the sources behind its answers and labels answers that come from a web search.

Answers draw on CASRAI's guides and dictionary plus the federal and funder documents we index: Federal Register, Grants.gov, Regulations.gov and UKRI.

Works on this site and inside Claude, Cursor and the AI tools you already use.

Everything CASRAI publishes — this page, the dictionary, the guides and the news — stays open to read, with no account and no card.

Referenced across the research world

University of Cambridge logoColumbia University logoCrossref logoUniversity of Edinburgh logoHarvard University logoUniversity of Oxford logoPrinceton University logoStanford School of Medicine logoUniversity College London logoORCID logoUniversity of Cambridge logoColumbia University logoCrossref logoUniversity of Edinburgh logoHarvard University logoUniversity of Oxford logoPrinceton University logoStanford School of Medicine logoUniversity College London logoORCID logo
  • University of Cambridge logo
  • Columbia University logo
  • Crossref logo
  • University of Edinburgh logo
  • Harvard University logo
  • University of Oxford logo
  • Princeton University logo
  • Stanford School of Medicine logo
  • University College London logo
  • ORCID logo

View CASRAI adoption →