Skip to main content
v2026.11,986 entries · CC-BY 4.0
LAC HealthSponsored

Shop tubing syringe supplies

  • FDA registered
  • ISO 13485
  • BBB Accredited A+

Shop at LAC Health

What Is a Tubing Syringe? Irrigating Syringe, Class and Connectors

A tubing (tube) syringe matches FDA’s irrigating syringe: a bulb or piston syringe with a tube. Class, how it differs from a piston syringe, connectors.

Written and maintained by CASRAI Editorial Board

Published · Last updated

On this page

“Tubing syringe” and “tube syringe” are not one standardized product name. People use them for a syringe that has a length of tubing attached or fitted to it. The one device class in US federal regulations that matches that description is the irrigating syringe: a bulb or piston syringe with an integral or detachable tube. This page explains that class, how it differs from a plain piston syringe, and which connector standards apply when tubing meets a syringe.

This page describes products and general use; it is not medical advice.

Who uses it: clinic and ward staff, home-care and supply buyers, and students looking for the correct device name before they search a catalogue.

What is a tubing syringe?

Under 21 CFR 880.6960, an irrigating syringe is a device that, in the regulation’s words, consists of a bulb or a piston syringe with an integral or a detachable tube, and is used to irrigate, withdraw fluid from, or instill fluid into, a body cavity or wound. That is the closest regulatory definition of a syringe with tubing. Catalogues may also list feeding-tube syringes, syringes sold with extension tubing, or bulb syringes under similar wording, so confirm the device name and intended use on the product label.

How a syringe with tubing is built

The regulation names two body styles: a bulb syringe (a squeezable reservoir) and a piston syringe (a graduated cylinder with a sliding plunger rod), plus the tube, which may be integral or detachable. A piston syringe on its own is defined separately in 21 CFR 880.5860 as a calibrated hollow barrel and a movable plunger, with a male connector (nozzle) at one end for fitting the female connector (hub) of a hypodermic single-lumen needle, used to inject fluids into or withdraw fluids from the body. For the tip styles used on syringe barrels, see syringe tip types; for the basics of the barrel and plunger, see what is a syringe.

Types and how they are classified

Device FDA identification (21 CFR) Class Key difference
Irrigating syringe 880.6960: bulb or piston syringe with an integral or detachable tube, used to irrigate, withdraw fluid from, or instill fluid into a body cavity or wound Class I (general controls); exempt from 510(k) subject to 880.9 The tube is part of the device definition
Piston syringe 880.5860: calibrated hollow barrel and movable plunger, with a male nozzle that fits the hub of a hypodermic single-lumen needle Class II (performance standards) Defined by the needle-hub connector, not by a tube

For irrigating syringes that are not labeled sterile, the regulation also exempts them from the quality system regulation in part 820 except for records and complaint-file requirements (820.35). Source: Cornell LII text of 21 CFR 880.6960 and 880.5860, read 2026-11-08.

Connectors that matter when tubing meets a syringe

Tubing and syringes are joined by small-bore connectors. FDA describes the ISO 80369 series, “Small-bore connectors for liquids and gases in healthcare applications,” as intended to reduce misconnections, where “small-bore” means an opening of less than 8.5 millimeters. Each part covers a different application:

ISO 80369 part Application
Part 1 (80369-1:2016) General requirements
Part 3 Enteral applications
Part 5 Limb cuff inflation applications
Part 6 Neuraxial applications
Part 7 Intravascular or hypodermic applications
Part 20 Common test methods

Source: FDA, “Reducing Risks Through Standards Development for Medical Device Connectors,” read 2026-11-08. The practical point is that a syringe and tube intended for one application (for example enteral feeding) are meant to use that application’s connector, so check the labeled application rather than assuming a tip will fit. Related pages: IV extension tubing, three-way stopcocks, feeding tubes and irrigation trays.

Safe use and handling basics

  • Use the device only for the purpose in its labeling; the regulatory definition above covers irrigating, withdrawing fluid from, or instilling fluid into a body cavity or wound.
  • Follow the manufacturer’s instructions for use for the specific product, including whether it is labeled sterile, single-use or reusable.
  • Do not substitute adapters to force a tube and syringe together; the connector standards exist to prevent misconnections between systems.
  • Questions about a particular patient or procedure belong with a clinician.

Common mistakes

  • Treating “tubing syringe” as a catalogue category: it is a descriptive phrase, and the device may be listed as an irrigating, feeding or bulb syringe.
  • Assuming a piston syringe and an irrigating syringe are the same class: FDA lists them under different regulations and classes (see the table above).
  • Assuming any tip fits any tube: connectors are separated by application under ISO 80369.

FAQ

What is a tube syringe?

“Tube syringe” is another wording for the same idea: a syringe with an integral or detachable tube. In FDA terms this matches the irrigating syringe, a bulb or piston syringe with an integral or detachable tube (21 CFR 880.6960).

Is a tubing syringe a regulated medical device?

An irrigating syringe is a Class I device under 21 CFR 880.6960, subject to general controls and exempt from 510(k) premarket notification subject to the limitations in 880.9.

Does a piston syringe include tubing?

Not by definition. 21 CFR 880.5860 describes a calibrated hollow barrel and a movable plunger, with a male nozzle for fitting a hypodermic needle hub; tubing is what makes it an irrigating syringe when attached.

Sources

  • 21 CFR 880.6960, irrigating syringe, law.cornell.edu, read 2026-11-08.
  • 21 CFR 880.5860, piston syringe, law.cornell.edu, read 2026-11-08.
  • FDA, Reducing Risks Through Standards Development for Medical Device Connectors, fda.gov, read 2026-11-08.

Follow CASRAI

Research-administration guidance, standards updates and independent tool reviews.

Ask CASRAI · free to try

Ask about What Is a Tubing Syringe? Irrigating Syringe, Class and Connectors

2 free questions a day, no account.

An AI assistant for research: funder rules, compliance, methods and publishing. It links the sources behind its answers and labels answers that come from a web search.

Answers draw on CASRAI's guides and dictionary plus the federal and funder documents we index: Federal Register, Grants.gov, Regulations.gov and UKRI.

Works on this site and inside Claude, Cursor and the AI tools you already use.

Everything CASRAI publishes — this page, the dictionary, the guides and the news — stays open to read, with no account and no card.

Referenced across the research world

University of Cambridge logoColumbia University logoCrossref logoUniversity of Edinburgh logoHarvard University logoUniversity of Oxford logoPrinceton University logoStanford School of Medicine logoUniversity College London logoORCID logoUniversity of Cambridge logoColumbia University logoCrossref logoUniversity of Edinburgh logoHarvard University logoUniversity of Oxford logoPrinceton University logoStanford School of Medicine logoUniversity College London logoORCID logo
  • University of Cambridge logo
  • Columbia University logo
  • Crossref logo
  • University of Edinburgh logo
  • Harvard University logo
  • University of Oxford logo
  • Princeton University logo
  • Stanford School of Medicine logo
  • University College London logo
  • ORCID logo

View CASRAI adoption →