Skip to main content
v2026.11,986 entries · CC-BY 4.0
LAC HealthSponsored

Shop blood transfer device supplies

  • FDA registered
  • ISO 13485
  • BBB Accredited A+

Shop at LAC Health

What Is a Blood Transfer Device? Types, Specs & Safe Use

A blood transfer device moves syringe-drawn blood safely into evacuated tubes. Compare device types, FDA Class II specs, OSHA rules, and transfer steps.

Written and maintained by CASRAI Editorial Board

Published

This page describes products and general use; it is not medical advice.

On this page

A blood transfer device is a single-use, sterile fluid-transfer accessory engineered to move syringe-drawn blood safely into evacuated collection tubes or blood culture bottles without exposing a sharp hypodermic needle. When clinical conditions require sampling via syringe—such as fragile veins, arterial punctures, or vascular lines—the blood must be transferred into tubes containing diagnostic additives. Blood transfer devices establish a closed, needle-shielded pathway that protects healthcare personnel from sharps injuries while preserving diagnostic specimen quality.

Phlebotomists, clinical laboratory scientists, nurses, and emergency medical personnel use blood transfer devices as standard safety engineering controls. Adopting these closed transfer units supports Good Clinical Laboratory Practice (GCLP) standards and safeguards biospecimen integrity during pre-analytical diagnostic workflows.

What It Is

A blood transfer device is a rigid safety adapter connecting a standard syringe to an evacuated blood collection tube. Rather than using an exposed needle to pierce a rubber stopper, the clinician threads the syringe directly onto the device’s female Luer connector. The collection tube is inserted into the outer barrel, where an enclosed internal needle pierces the stopper under continuous plastic shielding.

The device’s core purpose is to eliminate sharps hazards during syringe-to-tube blood dispensing while ensuring controlled, vacuum-driven filling that prevents specimen hemolysis and stopper displacement.

A common variant is the vacutainer transfer device (such as the BD Vacutainer® Blood Transfer Device). In hospital procurement and laboratory practice, these terms are used interchangeably to describe pre-assembled, single-use holders manufactured for closed specimen transfer.

How It Works and How It Is Built

A blood transfer device operates as a passive pressure interface. It does not require manual plunger depression; instead, it uses the calibrated negative pressure inside evacuated collection tubes to draw blood out of the syringe barrel.

Key Materials and Structural Parts

  • Outer Barrel: Molded from clear medical-grade polypropylene (PP). It aligns 13 mm and 16 mm collection tubes while shielding hands from the internal needle.
  • Female Luer-Lok Hub: An ISO 80369-7 compliant port that threads securely onto Luer-Lok syringe tips, creating an airtight, leak-free seal.
  • Internal Piercing Cannula: A short, double-ended stainless steel needle recessed within the barrel, inaccessible to accidental finger touch.
  • Elastomeric Resealing Sleeve: A synthetic rubber sheath covering the internal needle. It compresses during tube insertion and recovers over the needle tip upon tube removal, stopping leakage between multiple tubes.

Hemolysis Prevention and Fluid Mechanics

When collecting blood using standard clinical syringes, clinicians must avoid pushing the syringe plunger during transfer. Manufacturer instructions for use (IFU) and clinical laboratory standards strictly mandate passive vacuum filling.

Depressing the plunger generates high positive hydrostatic pressure, accelerating erythrocytes through the narrow internal cannula. High shear stress ruptures red cell membranes (hemolysis), releasing intracellular potassium and enzymes into plasma and skewing test results. Positive pressure can also dislodge the rubber stopper, creating biohazard splatter. Passive vacuum draw ensures smooth laminar flow, protecting cell structure and maintaining exact blood-to-additive ratios.

Types and Variants

Blood transfer devices are manufactured in specialized formats to accommodate standard vacuum tubes, wide-mouth culture bottles, or direct vascular line ports.

Device Variant Primary Indication Key Structural Feature Primary Reference
Standard Syringe Transfer Device Transferring syringe blood to 13 mm and 16 mm evacuated tubes. Female Luer-Lok hub with cylindrical polypropylene barrel. FDA Class II (21 CFR 862.1675, BD Ref 364880).
Blood Culture Transfer Unit Direct transfer to wide-neck blood culture bottles and tubes. Flared outer barrel fitting culture bottle caps. FDA Class II (Product Code JKA, VACUETTE® Ref 450225).
Direct Luer Access Device Direct collection from vascular catheter lines into tubes. Female Luer port with puncture needle; no syringe intermediary. FDA Class II (510(k) K222478, BD Ref 364902).
Urine Specimen Transfer Straw Aspirating urine from collection cups into vacuum tubes. Elongated suction straw without syringe Luer fitting. FDA Class I / 510(k) Exempt (BD Ref 364966).

Sizes and Specifications That Matter

Clinical buyers and lab supervisors evaluate transfer devices using standard parameters established by regulatory classifications and product monographs.

Specification Parameter Standard Clinical Specification Authority / Source
FDA Regulatory Classification Class II Medical Device (21 CFR 862.1675) U.S. FDA CDRH
FDA Product Code JKA (“Tubes, Vials, Systems, Serum Separators, Blood Collection”) FDA 510(k) K222478
GMDN Nomenclature 58136 (“Syringe/blood collection tube adaptor IVD”) GMDN Agency / AccessGUDID
Connector Geometry ISO 80369-7 female Luer-Lok thread ISO Standard 80369-7
Compatible Tube Diameters 13 mm and 16 mm outer diameter collection tubes CLSI GP41-A6
Culture Bottle Fit Accommodates standard automated culture bottles (e.g., BD BACTEC™) Manufacturer Technical Data
Sterility & Packaging Sterile fluid path, single-use, individual blister pack FDA AccessGUDID Database
Natural Rubber Latex Not made with natural rubber latex Product Safety Sheets
Disposal Standard Puncture-resistant sharps biohazard disposal as a single unit OSHA 29 CFR 1910.1030

How to Choose a Blood Transfer Device

Selecting an appropriate transfer device requires reviewing specific clinical requirements and safety mandates:

  • Target Container Dimensions: Standard devices fit conventional 13 mm and 16 mm serum separation tubes. If blood cultures are drawn, confirm the barrel accommodates wide-neck culture bottles to prevent bottle cracking.
  • Luer Connection Security: Choose ISO 80369-7 compliant Luer-Lok threading over friction-fit slip cones to prevent accidental detachment under fluid pressure.
  • Pre-Assembled Design: Clinical protocols should source pre-assembled units. Manually attaching needle components into separate holders increases sharps handling and violates OSHA engineering control directives.
  • Sterility Validation: Ensure devices for blood cultures and diagnostic tests are packaged in individual sterile blister packs to prevent bioburden contamination.

Safe Use and Handling Basics

Safe operation of a blood transfer device follows manufacturer IFU instructions and CLSI GP41-A6 guidelines:

  1. Inspect Package: Verify the sterile blister pack is intact. Peel back the paper backing to access the Luer port.
  2. Attach Syringe: Thread the blood-filled syringe clockwise onto the female Luer hub until secure. Avoid over-tightening.
  3. Orient Vertically: Hold the syringe vertically above the transfer device, pointing downward, ensuring blood contacts the internal needle.
  4. Insert Tube: Center the collection tube inside the barrel and push upward onto the needle until the stopper is punctured.
  5. Passive Draw: Do not touch the plunger. Let the vacuum pull blood until flow stops, preserving correct ratios of blood to evacuated tube additives.
  6. Follow Order of Draw: When filling multiple tubes, follow standard clinical sequence (blood cultures, citrate, serum, heparin, EDTA, fluoride). The rubber sleeve reseals between tubes.
  7. Dispose as an Intact Unit: Do not unscrew or detach the transfer device from the syringe. Discard the assembled unit directly into an approved sharps container.

Common Mistakes to Avoid

  • Depressing the Plunger: Manually pushing the plunger causes hemolysis, additive dilution errors, and potential stopper dislodgement.
  • Detaching After Use: Trying to unscrew the contaminated transfer device creates unnecessary sharps and blood exposure hazards.
  • Reusing Transfer Devices: Transfer devices are strictly single-use. Reusing them cross-contaminates specimens and spreads bloodborne pathogens.
  • Manual Needle Injection: Using hypodermic needles to inject blood into vacuum tubes violates OSHA Bloodborne Pathogens standard 29 CFR 1910.1030(d)(2).
  • Horizontal Orientation: Angling the syringe horizontally during fill introduces air into the needle bore, halting vacuum aspiration early.

Frequently Asked Questions

What is a vacutainer transfer device?

A vacutainer transfer device is an industry term for a sterile, pre-assembled holder featuring a female Luer-Lok port and a recessed puncture needle. It enables safe blood transfer from a syringe into evacuated collection tubes or culture bottles without exposed sharps or manual plunger pressure.

Why is a blood transfer device required instead of a syringe needle?

Injecting blood through a tube stopper with an exposed needle is a primary cause of accidental needlesticks. Blood transfer devices encase the needle inside a plastic barrel, satisfying OSHA mandates for engineering safety controls.

Can a blood transfer device be reused?

No. Blood transfer devices are single-use devices. After specimen collection, the entire syringe-transfer device assembly must be discarded into a biohazard sharps container.

What causes hemolysis during syringe blood transfer?

Hemolysis occurs when operators depress the syringe plunger during transfer. Forcing blood under pressure through the narrow cannula creates turbulent shear stress that ruptures red blood cells. Allowing passive vacuum draw preserves cell membrane integrity.

Sources

  • U.S. Food and Drug Administration (FDA): 510(k) Premarket Notification K222478, “BD Vacutainer® Luer-Lok™ Access Device, BD Vacutainer® Blood Transfer Device” (21 CFR 862.1675, Product Code JKA). Verified November 11, 2026.
  • U.S. Food and Drug Administration (FDA): Global Unique Device Identification Database (AccessGUDID), GMDN 58136 “Syringe/blood collection tube adaptor IVD”, DI 00382903648809. Verified November 11, 2026.
  • Occupational Safety and Health Administration (OSHA): Bloodborne Pathogens Standard, 29 CFR 1910.1030(d)(2) “Engineering and Work Practice Controls”. Verified November 11, 2026.
  • Clinical and Laboratory Standards Institute (CLSI): CLSI Standard GP41-A6, “Collection of Diagnostic Venous Blood Specimens”. Verified November 11, 2026.
  • Becton, Dickinson and Company (BD): BD Vacutainer® Blood Transfer Device Instructions for Use and Specifications (Ref 364880). Verified November 11, 2026.
  • Greiner Bio-One: VACUETTE® Blood Transfer Unit Product Specifications (Ref 450225). Verified November 11, 2026.

Follow CASRAI

Research-administration guidance, standards updates and independent tool reviews.

Ask CASRAI · free to try

Ask about What Is a Blood Transfer Device? Types, Specs & Safe Use

2 free questions a day, no account.

An AI assistant for research: funder rules, compliance, methods and publishing. It links the sources behind its answers and labels answers that come from a web search.

Answers draw on CASRAI's guides and dictionary plus the federal and funder documents we index: Federal Register, Grants.gov, Regulations.gov and UKRI.

Works on this site and inside Claude, Cursor and the AI tools you already use.

Everything CASRAI publishes — this page, the dictionary, the guides and the news — stays open to read, with no account and no card.

Referenced across the research world

University of Cambridge logoColumbia University logoCrossref logoUniversity of Edinburgh logoHarvard University logoUniversity of Oxford logoPrinceton University logoStanford School of Medicine logoUniversity College London logoORCID logoUniversity of Cambridge logoColumbia University logoCrossref logoUniversity of Edinburgh logoHarvard University logoUniversity of Oxford logoPrinceton University logoStanford School of Medicine logoUniversity College London logoORCID logo
  • University of Cambridge logo
  • Columbia University logo
  • Crossref logo
  • University of Edinburgh logo
  • Harvard University logo
  • University of Oxford logo
  • Princeton University logo
  • Stanford School of Medicine logo
  • University College London logo
  • ORCID logo

View CASRAI adoption →