Skip to main content
v2026.11,986 entries · CC-BY 4.0
LAC HealthSponsored

Shop 3m 7502 supplies

  • FDA registered
  • ISO 13485
  • BBB Accredited A+

Shop at LAC Health

3M 7502 Half Facepiece: Specs, APF 10 & Lab Use

Guide to the 3M 7502 silicone half-facepiece respirator, covering NIOSH 42 CFR 84 ratings, OSHA APF 10 compliance, and laboratory safety protocols.

Written and maintained by CASRAI Editorial Board

Published

On this page

The 3M 7502 is a reusable half-facepiece elastomeric respirator manufactured from advanced medical-grade silicone. Serving as the medium-sized model in the 3M 7500 Series, it carries an Assigned Protection Factor (APF) of 10 under OSHA 29 CFR 1910.134. It features a downward-exhausting Cool Flow valve and reverse-bayonet fittings compatible with NIOSH 42 CFR 84 particulate filters and chemical cartridges.

This page describes products and general use; it is not medical advice.

Short answer

The 3M 7502 is an elastomeric half-mask respirator designed for occupational safety across laboratory, clinical, and industrial environments. Made from supple silicone rubber, the medium-sized 7502 forms a durable seal against the wearer’s face, filtering airborne hazards when equipped with approved particulate filters or gas cartridges. It provides an OSHA Assigned Protection Factor of 10, reducing airborne exposure up to ten times the permissible exposure limit. The facepiece features a downward exhalation valve that lowers breathing resistance and prevents eyewear fogging, alongside a dual-mode harness that permits drop-down wear during bench breaks.

Definition and scope

The 3M 7502 is an elastomeric half-mask respirator (EHR)—a reusable protective device covering the nose, mouth, and chin. Unlike disposable filtering facepieces such as 3M Aura disposable respirators, an elastomeric half-face respirator uses an impermeable silicone body cleaned and reused across hundreds of cycles, while spent filter media or cartridges are replaced.

The 7500 Series includes three discrete sizes to fit standard facial distributions:

  • 7501 (Small): Light blue yoke assembly, suited for smaller facial profiles.
  • 7502 (Medium): Light gray yoke assembly, fitting the majority of adult facial dimensions.
  • 7503 (Large): Dark blue yoke assembly, designed for wider or longer facial features.

Certification is governed by NIOSH under 42 CFR Part 84. NIOSH approves complete assemblies rather than bare facepieces; approved pairings of the 7502 with 3M filters or cartridges carry TC-84A approval numbers on the NIOSH Certified Equipment List (CEL).

How it works or how it is used in practice

The 3M 7502 operates on negative-pressure air-purifying filtration. Inhalation draws ambient air through twin bayonet ports and attached filters, passing through silicone inhalation valves into the breathing chamber. During exhalation, the inhalation valves close while the central exhalation valve opens.

The 7502 features 3M’s Cool Flow valve, sheltered by a rigid cover that deflects warm, moist breath downward. This prevents upward airflow beneath safety glasses or face shields, eliminating lens fogging. The four-point suspension harness offers two modes:

  • Standard Mode: The upper cradle sits over the crown while neck straps fasten behind the head, maintaining continuous sealing pressure during active tasks.
  • Drop-Down Mode: Webbing slides through yoke guides, allowing the wearer to unlatch the neck strap and lower the mask to rest on the chest during breaks without removing headgear.

Under OSHA 29 CFR 1910.134, workplace use requires enrollment in an institutional laboratory respiratory protection program, including medical clearance (Appendix C), passing an annual OSHA respirator fit test (qualitative or quantitative per Appendix A), and performing daily positive and negative user seal checks (Appendix B-1) upon every donning.

Evaluating the 3M 7502 involves comparing chassis materials against alternative models and understanding its modular bayonet media ecosystem.

Model / Series Chassis Material Exhalation Valve Style Harness Configuration Operational Role and Distinction
3M 7502 (7500 Series) Medical-grade silicone Downward Cool Flow valve Dual-mode (standard and drop-down) Comfort for extended benchwork; high thermal resilience; lower contact pressure.
3M 6200 (6000 Series) Thermoplastic elastomer (TPE) Standard front exhaust valve Fixed cradle harness Economical half mask; firmer seal with higher contact pressure; non-drop-down.
3M 6502QL (6500QL Series) Textured silicone blend Downward Cool Flow valve Quick Latch drop-down latch One-touch front lever unlatches facepiece instantly for rapid off-face transitions.
3M FF-402 (Ultimate FX) Silicone full facepiece Downward Cool Flow valve Six-strap comfort cradle APF 50 full-face protection combining respiratory defense with ocular splash coverage.

The reverse-bayonet ports accept several NIOSH 42 CFR 84 approved filter types:

  • Particulate Filters (2000 Series): Disc filters like the 2091 P100 (99.97% efficient against oil and non-oil aerosols) or 2097 P100 (adding carbon for nuisance organic vapors).
  • Encapsulated Filters (7093 Series): Hard-shell P100 filters protecting media against liquid splashes, sparks, and wipe-downs.
  • Chemical Cartridges (6000 Series): Sorbent pods containing treated activated carbon, such as 6001 (Organic Vapors), 6003 (Acid Gases / Organic Vapors), and 6006 (Multi-Gas/Vapor covering ammonia, chlorine, and formaldehyde).
  • Combination Systems (5000 Series): Pre-filters (5N11 N95 or 5P71 P95) snapped onto 6000 cartridges using 3M 501 retainers for simultaneous aerosol and vapor capture.

Where it matters for labs, clinics or supply decisions

The 3M 7502 is suited for settings requiring durable chemical compatibility and all-day comfort:

  • Chemical Handling: Handles volatile reagents during solvent dispensing, acid vapor work, or rotary evaporator maintenance outside ducted fume hoods.
  • Pathology and Histology: Protects grossing staff against formaldehyde and xylene exposure when equipped with 6006 multi-gas cartridges.
  • Vivarium and Aerosol Work: Captures animal dander and bioaerosols using 2091 P100 filters without mask collapse.
  • Spill Response: Maintained on institutional emergency spill carts for quick chemical containment.
  • Supply Economics: Silicone bodies last years under OSHA Appendix B-2 cleaning protocols (less than 49°C / 120°F wash), reducing disposable N95 waste and procurement costs.

Common misunderstandings

Common operational misunderstandings include:

  • Assuming the facepiece alone determines protection: The 7502 is only a chassis; particulate filters provide no vapor defense, and gas cartridges provide no particulate capture unless combined.
  • Confusing APF 10 with filter efficiency: A 99.97% P100 filter does not grant a protection factor of 1,000; OSHA Table 1 restricts all half-masks to APF 10 (maximum 10× PEL) due to faceseal boundary dynamics.
  • Using valved masks in sterile fields: The Cool Flow valve exhausts unfiltered breath downward; valved masks are prohibited in sterile fields requiring sterile source control.
  • Skipping daily user seal checks: Passing an annual fit test does not replace mandatory positive and negative user seal checks required every time the mask is donned.
  • Entering IDLH or low-oxygen areas: Air-purifying respirators do not generate oxygen; using the 7502 in atmospheres with less than 19.5% oxygen or in IDLH conditions is life-threatening.

Frequently asked questions

What does the 7502 designation mean in the 3M product line?

Model 7502 denotes the Medium size within the 3M 7500 Series silicone half-facepiece line. Sister models are the 7501 (Small, light blue yoke) and 7503 (Large, dark blue yoke). The medium 7502 features a light gray yoke and fits the majority of adult facial structures.

Can the 3M 7502 be used for biological hazard protection?

Yes, when fitted with NIOSH-approved P100 particulate filters (such as 2091 or 7093), the 7502 provides APF 10 protection against airborne pathogens and fungal spores. However, it cannot be used where sterile source control is mandatory due to its open exhalation valve.

How should the 3M 7502 facepiece be cleaned and maintained?

Under OSHA 29 CFR 1910.134 Appendix B-2, remove cartridges and immerse the silicone chassis in warm water (less than 49°C / 120°F) with neutral detergent. Disinfect with an approved quaternary ammonium or bleach solution, rinse in clean water, air dry, inspect valves, and store in a sealed container.

When should 3M cartridges and filters on the 7502 be replaced?

Replace particulate filters when breathing resistance increases noticeably or when physically soiled. Replace chemical cartridges according to an established OSHA change-out schedule or immediately upon detecting chemical odor, taste, or irritation.

Sources

  • Occupational Safety and Health Administration (OSHA). (2026). Standard 29 CFR 1910.134: Respiratory Protection. United States Department of Labor. Read November 9, 2026. https://www.osha.gov/laws-regs/regulations/standardnumber/1910/1910.134
  • National Institute for Occupational Safety and Health (NIOSH). (2026). NIOSH Certified Equipment List (CEL): 42 CFR Part 84 Certified Respirators. Centers for Disease Control and Prevention. Read November 9, 2026. https://wwwn.cdc.gov/niosh-cel/
  • Legal Information Institute (LII). (2026). 42 CFR Part 84: Approval of Respiratory Protective Devices. Cornell Law School. Read November 9, 2026. https://www.law.cornell.edu/cfr/text/42/part-84
  • 3M Occupational Health and Environmental Safety Division. (2026). 3M™ Half Facepiece Reusable Respirators 7500 Series Technical Specifications and User Instructions. 3M Company. Read November 9, 2026.

Follow CASRAI

Research-administration guidance, standards updates and independent tool reviews.

Ask CASRAI · free to try

Ask about 3M 7502 Half Facepiece: Specs, APF 10 & Lab Use

2 free questions a day, no account.

An AI assistant for research: funder rules, compliance, methods and publishing. It links the sources behind its answers and labels answers that come from a web search.

Answers draw on CASRAI's guides and dictionary plus the federal and funder documents we index: Federal Register, Grants.gov, Regulations.gov and UKRI.

Works on this site and inside Claude, Cursor and the AI tools you already use.

Everything CASRAI publishes — this page, the dictionary, the guides and the news — stays open to read, with no account and no card.

Referenced across the research world

University of Cambridge logoColumbia University logoCrossref logoUniversity of Edinburgh logoHarvard University logoUniversity of Oxford logoPrinceton University logoStanford School of Medicine logoUniversity College London logoORCID logoUniversity of Cambridge logoColumbia University logoCrossref logoUniversity of Edinburgh logoHarvard University logoUniversity of Oxford logoPrinceton University logoStanford School of Medicine logoUniversity College London logoORCID logo
  • University of Cambridge logo
  • Columbia University logo
  • Crossref logo
  • University of Edinburgh logo
  • Harvard University logo
  • University of Oxford logo
  • Princeton University logo
  • Stanford School of Medicine logo
  • University College London logo
  • ORCID logo

View CASRAI adoption →