Skip to main content
v2026.11,986 entries · CC-BY 4.0

Hazard Class 2.2: Non-Flammable, Non-Toxic Gas Under 49 CFR 173.115

Hazard Class 2.2 is the U.S. DOT class for non-flammable, nonpoisonous compressed gases: the 200 kPa test, green label, placard and cylinder rules.

Written and maintained by CASRAI Editorial Board

Published

On this page

Hazard Class 2.2 (Division 2.2) is the U.S. Department of Transportation category for non-flammable, nonpoisonous compressed gases: gases that are packaged under pressure, or are liquefied or refrigerated, and that are neither flammable (Division 2.1) nor toxic by inhalation (Division 2.3). In a laboratory it is the class that argon, nitrogen and compressed air cylinders travel under, and it is defined in 49 CFR 173.115(b).

Definition and the two-part test in 49 CFR 173.115(b)

The federal hazardous materials regulations place gases in Class 2 and split the class into three divisions. Division 2.2 is described in 49 CFR 173.115(b) as a “non-flammable, nonpoisonous compressed gas”, and the regulation lists what the term includes: compressed gas, liquefied gas, pressurized cryogenic gas, compressed gas in solution, asphyxiant gas and oxidizing gas. The phrase is a transport classification, not a statement that the contents are harmless.

The regulation then gives a test with two parts. A material or mixture is in Division 2.2 when it meets both of these:

  1. In the packaging it exerts a gauge pressure of 200 kPa (29.0 psig, 43.8 psia) or greater at 20 °C (68 °F), or it is a liquefied gas, or it is a cryogenic liquid; and
  2. It does not meet the definition of Division 2.1 (flammable gas) or Division 2.3 (gas poisonous by inhalation).

Because the second part is defined by exclusion, Division 2.2 is the residual gas division. A gas reaches it by being pressurized, liquefied or cryogenic and then failing the flammability and toxicity tests that would have put it in 2.1 or 2.3. The data table below sets the three tests side by side.

The 200 kPa figure

Some secondary pages on the topic quote a different pressure threshold for Division 2.2. The 49 CFR 173.115(b) text as published by the Legal Information Institute at Cornell Law School states 200 kPa gauge pressure at 20 °C, so that is the figure to use when the question is the U.S. definition. Training material uses yet another description: the FEMA Emergency Management Institute course IS-0005a defines a compressed gas as one with an absolute pressure exceeding 40 psi at 70 °F, and describes Division 2.2 as non-flammable, non-toxic compressed gases. That is a general training definition of “compressed gas” and not the regulatory test for the division, so cite the regulation when the number matters.

How Division 2.2 shows up on a package, a vehicle and a shipping paper

Classification is only the first link in a chain. For a laboratory that ships or receives cylinders, the same division number drives the hazard label, the placard and the entry in the hazardous materials table.

The hazard communication table entry

The Hazardous Materials Table in 49 CFR 172.101 lists each proper shipping name with its hazard class or division in column 3 and its label codes in column 6. Entries in the table whose class is 2.2 carry the label code “Non-Flammable Gas”. Entries seen in the table include Air, compressed (UN1002), Argon, compressed (UN1006) and Adsorbed gas, n.o.s. (UN3511), all in Division 2.2. NOAA’s CAMEO Chemicals database gives the same classification for Nitrogen, compressed (UN1066): DOT hazard class 2.2, label “2.2 non-flammable non-poisonous gas”, and Emergency Response Guidebook guide 120, “Gases – Inert (including refrigerated liquids)”.

The label

49 CFR 172.415 sets the NON-FLAMMABLE GAS label for Division 2.2 and requires a green background. The label name and the green background are the identifying features set in the regulation; the label name matches the “Non-Flammable Gas” label code in the 172.101 table.

The placard

Division 2.2 is listed in Table 2 of 49 CFR 172.504 only, and the placard is NON-FLAMMABLE GAS (172.528). The section sets out several conditions that change what a vehicle must display:

  • A vehicle carrying less than 454 kg (1,001 lb) aggregate gross weight of Table 2 materials does not need to be placarded for them on highway or rail transport, provided the materials are not in bulk packaging and are not materials that 172.505 treats separately.
  • Under 172.504(f)(7), domestic transportation of compressed or refrigerated liquid oxygen may be placarded OXYGEN (172.530) in place of NON-FLAMMABLE GAS.
  • Under 172.504(f)(3), the NON-FLAMMABLE GAS placard is not required on a vehicle that also carries flammable gas or oxygen and is already placarded FLAMMABLE GAS or OXYGEN.

The 454 kg figure is a vehicle placarding rule. The package label requirement is a separate provision (172.415 above), and the placarding exceptions should not be read as removing the need to label or mark individual packages.

Cylinder rules that apply to compressed Division 2.2 gases

When the Division 2.2 gas is compressed in a cylinder, 49 CFR 173.301 sets general requirements for compressed gases in UN pressure receptacles or in DOT and ICC specification metal cylinders built to parts 178 and 180. Among them, as read on the Legal Information Institute copy of the regulation:

  • A cylinder that is overdue for requalification may not be filled (173.301(a)(6)).
  • Valve protection caps manufactured on or after 7 November 2019 must conform to CGA V-9 (Compressed Gas Association standard).
  • For cylinders manufactured on or after 1 October 2007, the valve assembly must be strong enough, or protected, so that no leakage occurs (173.301(h)(3)).
  • Cracked, leaking, bulging or heavily corroded cylinders may not be filled or offered for transportation.

These requirements are the reason the class matters beyond a label colour: a “non-flammable” gas still moves inside a pressure vessel with its own requalification, valve and condition rules. For the end-of-life side of the same equipment, see the CASRAI guide to compressed gas cylinder disposal.

Division 2.2 compared with Divisions 2.1 and 2.3

The three divisions of Class 2 are separated by what the gas can do apart from being under pressure. Division 2.1 is the flammable gas division: under 49 CFR 173.115(a) a gas qualifies if it is ignitable at 101.3 kPa in a mixture of 13 percent or less by volume with air, or has a flammable range with air of at least 12 percentage points regardless of the lower limit. Division 2.3 covers gases known to be so toxic to humans that they pose a hazard in transport, and 173.115(c) presumes a gas toxic when its LC50 is not more than 5000 mL/m³ and there is no human data. Division 2.2 is what remains from the pressurized, liquefied and cryogenic gases after those two tests.

The data table below compares the three divisions, the regulation paragraph that defines each, and the test that separates them. Its entries come directly from 49 CFR 173.115 and the FEMA course page.

Aerosols

Aerosols are an example of how the division reaches beyond cylinders. Under 49 CFR 173.115(l)(2), an aerosol is assigned to Division 2.2 if its contents contain 1% by mass or less of flammable components and the heat of combustion is less than 20 kJ/g. Under (l)(4), Division 2.3 gases may not be transported in an aerosol container.

Where the class matters for laboratories

Division 2.2 is the class under which compressed air, argon and nitrogen are listed (UN1002, UN1006 and UN1066 above), so it is the class a laboratory meets when it ships or receives those gases as dangerous goods. Three practical connections to related CASRAI pages:

  • Safety data sheets. The safety data sheet is the document that describes a specific gas in full, and the transport class is one part of that picture. The CASRAI guides to nitrogen gas SDS and carbon dioxide SDS explain the safety data sheets for two gases commonly held in laboratories.
  • Other classes in the same shipment. A cylinder is not the only dangerous good a laboratory sends or receives. The guide to hazmat Class 3 flammable liquids covers the liquid side, and the primer on common lab chemical hazard classes places Class 2 alongside the rest.
  • The wider regulatory frame. The classification, label and placard provisions sit in Parts 172 and 173 of Title 49. The CASRAI guide to 49 CFR Part 172 describes the communication requirements, and the IATA Dangerous Goods Regulations are the air-transport counterpart.

Common misunderstandings

“Non-flammable, non-toxic means safe to ignore”

The wording in 49 CFR 173.115(b) names asphyxiant gas and oxidizing gas as part of Division 2.2. The division records that the gas is not flammable (2.1) and not toxic by inhalation (2.3); the regulation itself lists asphyxiant and oxidizing gases inside the division, and the cylinder rules in 173.301 apply to the pressurized container whatever the contents.

“Division 2.2 means the pressure threshold is 280 kPa”

Several secondary pages give 280 kPa. The CFR text read at Cornell LII says 200 kPa (29.0 psig) gauge at 20 °C, and also brings in every liquefied gas and cryogenic liquid regardless of pressure.

“If it is under 1,001 lb nothing is required”

The 454 kg (1,001 lb) figure in 172.504 is a threshold for placarding a vehicle carrying Table 2 materials in non-bulk packaging. It is not an exemption from classifying the gas, labelling the package or meeting the cylinder requirements in 173.301.

“The label and the placard are the same thing”

The label (172.415) goes on the package, with a green background for NON-FLAMMABLE GAS. The placard (172.504 and 172.528) goes on the vehicle or freight container, and for domestic liquid oxygen the OXYGEN placard may be substituted under 172.504(f)(7).

“All gases in a cylinder are Class 2.2”

Class 2 also holds flammable gases (2.1) and toxic gases (2.3). Aerosols follow the 1% by mass and 20 kJ/g test, and Division 2.3 gases cannot be shipped in aerosol containers at all. The class of any specific gas comes from its entry in the 172.101 table, not from the container type.

Sources

Data: U.S. DOT Class 2 gas divisions compared (49 CFR 173.115)

Compares the three divisions of Hazard Class 2 gases in the U.S. hazardous materials regulations: the defining regulation paragraph and the test that places a gas in each division. Compiled from the text of 49 CFR 173.115 and the FEMA IS-0005a course description of Class 2.

Coverage: United States.

U.S. DOT Class 2 gas divisions compared (49 CFR 173.115)
DivisionNameCFR paragraphDefining test
2.1Flammable gas49 CFR 173.115(a)Ignitable at 101.3 kPa in a mixture of 13 percent or less by volume with air, or a flammable range with air of at least 12 percent regardless of the lower limit
2.2Non-flammable, nonpoisonous compressed gas49 CFR 173.115(b)Gauge pressure of 200 kPa (29.0 psig) or greater at 20 °C in the packaging, or a liquefied gas, or a cryogenic liquid; and does not meet Division 2.1 or 2.3
2.3Gas poisonous by inhalation49 CFR 173.115(c)Known to be so toxic to humans as to pose a hazard in transport, or presumed toxic when LC50 is not more than 5000 mL/m3 absent human data

Sources

Compiled by CASRAI from the sources above. Free to reuse under CC BY 4.0 with attribution.

Follow CASRAI

Research-administration guidance, standards updates and independent tool reviews.

Ask CASRAI · free to try

Ask about Hazard Class 2.2: Non-Flammable, Non-Toxic Gas Under 49 CFR 173.115

2 free questions a day, no account.

An AI assistant for research: funder rules, compliance, methods and publishing. It links the sources behind its answers and labels answers that come from a web search.

Answers draw on CASRAI's guides and dictionary plus the federal and funder documents we index: Federal Register, Grants.gov, Regulations.gov and UKRI.

Works on this site and inside Claude, Cursor and the AI tools you already use.

Everything CASRAI publishes — this page, the dictionary, the guides and the news — stays open to read, with no account and no card.

Referenced across the research world

University of Cambridge logoColumbia University logoCrossref logoUniversity of Edinburgh logoHarvard University logoUniversity of Oxford logoPrinceton University logoStanford School of Medicine logoUniversity College London logoORCID logoUniversity of Cambridge logoColumbia University logoCrossref logoUniversity of Edinburgh logoHarvard University logoUniversity of Oxford logoPrinceton University logoStanford School of Medicine logoUniversity College London logoORCID logo
  • University of Cambridge logo
  • Columbia University logo
  • Crossref logo
  • University of Edinburgh logo
  • Harvard University logo
  • University of Oxford logo
  • Princeton University logo
  • Stanford School of Medicine logo
  • University College London logo
  • ORCID logo

View CASRAI adoption →