Skip to main content
v2026.11,986 entries · CC-BY 4.0
LAC HealthSponsored

Shop refill oxygen tanks supplies

  • FDA registered
  • ISO 13485
  • BBB Accredited A+

Shop at LAC Health

How to Refill Oxygen Tanks: Who May Fill Them and What to Check

Who may refill an oxygen tank, what to check first (test date, damage, owner consent) and how to store cylinders. General information, not medical advice.

Written and maintained by CASRAI Editorial Board

Published · Last updated

On this page

Short answer: an oxygen cylinder is refilled by a qualified filler, usually through a supplier exchange or delivery, or, where a prescriber and supplier have arranged one, with a home-fill device used strictly to its manufacturer’s instructions. It is not a do-it-yourself job with an air compressor or an industrial gas source. This page is general product and safety information, not medical advice; it does not tell anyone how to set up or adjust their own oxygen therapy.

It is written for a person or a facility that holds an oxygen cylinder and needs to know who may fill it, what to check before it is filled, and how to store it. The regulatory points below come from the U.S. Department of Transportation (49 CFR 173.301) and OSHA (29 CFR 1910.101), both checked on 1 November 2026.

What you need

  • The cylinder’s markings and test date. The DOT stamp and the requalification date tell a filler whether the cylinder may be filled. See how to read the DOT stamp on an oxygen cylinder.
  • A qualified filler. In practice this means your oxygen supplier or a medical gas distributor, not a general workshop. Distribution rules are covered in medical gas licensing.
  • Proof of who owns the cylinder. Under 49 CFR 173.301(e), a cylinder filled with a hazardous material may not be offered for transportation unless it was filled by its owner or with the owner’s consent.
  • The written instructions for any home-fill device, if a supplier has set one up for you. Use only the cylinders, connectors and steps the manufacturer’s instructions for use specify.
  • A place to keep cylinders while you wait for the exchange. See the storage answer below.

Steps

These are the steps for the person holding the cylinder. They describe what to check and who to involve, not how to fill a cylinder from a high-pressure source.

  1. Read the cylinder markings. Find the DOT specification and the most recent test (requalification) date.
  2. Look at the cylinder. Do not hand over or try to use a cylinder with a visible crack, a bulge, a leaking or damaged valve, or signs of fire, heat damage or heavy corrosion. The regulation says such a cylinder may not be filled and offered for transportation; tell the supplier instead.
  3. Choose the route. The usual routes are an exchange (you return an empty cylinder and receive a filled one) or a scheduled delivery from your supplier. A home-fill device is a third route that exists for some users, set up through a supplier and a prescriber. A fourth route, filling it yourself from an air compressor or an industrial gas source, is not one to use.
  4. Ask the supplier the key questions (see the checklist below) before the cylinder leaves your hands.
  5. Connect or disconnect only as the equipment instructions say, and only with the correct regulator or connector for that cylinder. See oxygen cylinder parts for what the valve, cap and pressure relief device are.
  6. Store the cylinder as the storage answer below and the linked storage guide describe.

Questions to ask the supplier

Question Why it matters Source
Is this cylinder within its requalification period? No person may fill a cylinder overdue for periodic requalification with a hazardous material and then offer it for transportation. 49 CFR 173.301(a)(6)
Has the outside of the cylinder been inspected before filling? The person filling a cylinder must visually inspect its outside before each filling. 49 CFR 173.301(a)(2)
Who owns the cylinder, and does the owner consent to this fill? A filled cylinder may not be offered for transportation unless filled by its owner or with the owner’s consent. 49 CFR 173.301(e)
Are the cylinder’s pressure relief devices leak-tested before it ships from the filling plant? The regulation requires pressure relief devices to be tested for leaks before a filled cylinder is shipped from the cylinder filling plant. 49 CFR 173.301(a)(3)
(Facilities) Who determines the cylinders under our control are in a safe condition? Each employer must determine that compressed gas cylinders under its control are in a safe condition, to the extent this can be determined by visual inspection. 29 CFR 1910.101(a)

How to refill oxygen tanks at home

Answer: at home, an oxygen tank is not refilled by the user from a general source. The two routes that exist are a supplier exchange or delivery, and a home-fill device that a supplier and prescriber have arranged and that is operated only according to the manufacturer’s instructions for use. Those instructions are the authority for connection, fill and any limits on the cylinders that may be used.

A home-fill device is usually paired with an oxygen concentrator; see what an oxygen concentrator is and oxygen concentrator vs O2 tank for how the two differ.

How to refill oxygen tanks at home with a compressor or industrial source

Answer: do not. Federal cylinder-filling rules place the duty to inspect, to check the requalification date and to test the pressure relief devices on the person filling the cylinder, and the owner’s consent is required for a cylinder to be offered for transportation. A home setup with an air compressor meets none of those controls. Oxygen also makes fire worse, so see home oxygen safety before handling any oxygen equipment.

What is the correct way to store oxygen cylinders?

Answer: OSHA’s rule, 29 CFR 1910.101(b), requires in-plant handling and storage of compressed gas cylinders to follow Compressed Gas Association pamphlet P-1; the practical conditions are set out in compressed gas cylinder storage requirements. The home-use fire hazards of oxygen are in home oxygen safety. Cylinders of different sizes are covered in oxygen cylinder sizes, and moving them in oxygen tank carts.

What can go wrong

  • The cylinder is overdue for requalification. A filler may not fill it and offer it for transportation. Check the date first.
  • The cylinder is damaged. Cracks, leaks, bulges, a defective valve or pressure relief device, heat or fire damage and detrimental rusting or corrosion all rule out filling and transport under 49 CFR 173.301(a)(2).
  • The fill source is not an oxygen supplier. A compressor or industrial source is not a qualified filling route.
  • Fire risk around oxygen equipment. See home oxygen safety.
  • The cylinder belongs to someone else. A cylinder filled without the owner’s consent may not be offered for transportation.
  • The label is unreadable. If the stamp cannot be read, the requalification date cannot be confirmed; ask the supplier.

When to get professional help

  • Any time the cylinder is damaged, leaking, or the valve will not operate normally: stop using it and contact the supplier.
  • When the requalification date is passed or cannot be found.
  • Before using any home-fill device: ask the supplier and prescriber who arranges it and what training comes with it.
  • In a facility: your employer’s safety officer or the gas supplier, since the employer carries the safe-condition duty under 29 CFR 1910.101(a).

FAQ

Can I refill an oxygen tank myself?

Not from a general or industrial source. The routes that exist are a supplier exchange or delivery, or a supplier-arranged home-fill device used as the manufacturer’s instructions say.

How do I know whether my cylinder can be filled?

Check that it is within its requalification period and free of damage. The filler must also inspect it before each fill. See the DOT stamp guide.

Does the oxygen inside a cylinder expire?

See does oxygen expire for the sourced answer on gas and cylinder dates.

What is the correct way to store oxygen cylinders?

In-plant storage of compressed gas cylinders follows CGA pamphlet P-1 under 29 CFR 1910.101(b); the practical conditions are in compressed gas cylinder storage requirements.

How to refill oxygen tank at home?

Through a supplier route or an arranged home-fill device as described above; never with a compressor.

Sources

Follow CASRAI

Research-administration guidance, standards updates and independent tool reviews.

Ask CASRAI · free to try

Ask about How to Refill Oxygen Tanks: Who May Fill Them and What to Check

2 free questions a day, no account.

An AI assistant for research: funder rules, compliance, methods and publishing. It links the sources behind its answers and labels answers that come from a web search.

Answers draw on CASRAI's guides and dictionary plus the federal and funder documents we index: Federal Register, Grants.gov, Regulations.gov and UKRI.

Works on this site and inside Claude, Cursor and the AI tools you already use.

Everything CASRAI publishes — this page, the dictionary, the guides and the news — stays open to read, with no account and no card.

Referenced across the research world

University of Cambridge logoColumbia University logoCrossref logoUniversity of Edinburgh logoHarvard University logoUniversity of Oxford logoPrinceton University logoStanford School of Medicine logoUniversity College London logoORCID logoUniversity of Cambridge logoColumbia University logoCrossref logoUniversity of Edinburgh logoHarvard University logoUniversity of Oxford logoPrinceton University logoStanford School of Medicine logoUniversity College London logoORCID logo
  • University of Cambridge logo
  • Columbia University logo
  • Crossref logo
  • University of Edinburgh logo
  • Harvard University logo
  • University of Oxford logo
  • Princeton University logo
  • Stanford School of Medicine logo
  • University College London logo
  • ORCID logo

View CASRAI adoption →