Written and maintained by CASRAI Editorial Board
Published
On this page
Microscope slide preparation is the set of steps that turns a specimen into something a microscope can resolve: the specimen is placed on a glass slide, stabilised or fixed so it does not move or degrade, optionally stained, and usually covered with a coverslip. Which route you take depends on what you need to see: a wet mount shows live organisms and motion, a heat- or methanol-fixed smear gives a permanent layer of cells that can be stained, and a paraffin tissue section gives a thin, mountable slice of structure.
This guide compares the four common routes, wet mount, potassium hydroxide (KOH) mount, smear and fixation, and microtome tissue section, using a public-health laboratory training exercise from the US Centers for Disease Control and Prevention (CDC) and university teaching material on histology and microbiology. It covers preparation only; it does not cover specimen collection, and it does not repeat the slide-type overview in What Is a Microscope Slide?. The data table below the guide lines up the four routes side by side.
What slide preparation involves
Every preparation answers the same three questions: how will the specimen be held on the glass, what will keep it in a condition worth examining, and how will its parts become visible. In the sources read for this page, the answers fall into a short list. The specimen is held either in a drop of liquid under a coverslip (a wet mount), spread as a thin layer and attached to the glass (a smear), or sliced thin enough to lie flat on the glass (a tissue section). It is kept in a useful condition either by examining it at once, while it is still unchanged, or by fixation. Its parts become visible through stains or through the contrast of the liquid and the optics.
Fixation is the step most often misunderstood. Columbia University’s histology laboratory defines it as a chemical or physical method of killing the tissue while retaining the characteristic peculiarities of shape and structure. The LibreTexts Introduction to Microbiology chapter on sample preparation adds that fixation attaches cells to the slide and kills organisms, halting movement and metabolism while preserving cell components. Fixation is therefore a trade: you lose live behaviour and gain a stable specimen that survives staining.
Wet mount
A wet mount is the simplest preparation. LibreTexts describes it as one in which the specimen is placed on the slide in a drop of liquid, and notes that stains are often added to that liquid. The CDC’s routine microscopy student exercise gives the same sequence in its plainest form: place a drop of the specimen on a labeled slide, add a coverslip, and observe at once using the 40X objective. The exercise example is Trichomonads, organisms of roughly 15 micrometres (µm), which is why the exercise tells students to look immediately: a wet mount is a preparation for seeing live organisms and their movement, and the specimen is not fixed.
The practical consequence is timing. Because nothing is fixed or dried, a wet mount is read straight away and is not kept as a permanent slide. The CDC exercise lists sterile saline or water among the materials for this reason: the liquid is part of the preparation, not just a carrier. For what the coverslip itself is, and why it is used, see What Is a Coverslip?
KOH mount
A KOH mount is a wet mount with one added reagent. In the CDC exercise, a drop of the specimen is placed on a labeled slide, a drop of KOH is added, a coverslip goes on, and the slide is observed at 40X. The exercise uses it to find yeast and pseudohyphae, and it gives the size ranges students should expect: yeast cells 2 to 6 µm and pseudohyphae 20 to 100 µm. Those figures matter as a calibration aid. A trainee who knows the expected size range can tell a yeast cell from debris at 40X by comparing it with the field, rather than guessing.
Smear and fixation
A smear is a thin layer of material spread on the slide. LibreTexts explains that a smear is briefly heated over a heat source, which is heat fixation, and it adds that chemical fixatives are often preferable to heat for tissue specimens. The chemical agents it lists are acetic acid, ethanol, methanol, formaldehyde (formalin) and glutaraldehyde. The CDC exercise reflects both options in its materials list: a slide warmer or Bunsen burner, optional, for heat fixing the smear, and methanol, also optional, for fixing the smear chemically.
The same sources explain what comes after fixation. Positive stains colour the cells, while negative stains colour the background so the cells appear as clear shapes. Which you choose depends on whether you want to see cell detail or just cell outline and arrangement. A worked example of a smear-based stain, with reagents and expected results, is in Gram stain: procedure, reagents and results, and the slide features that matter for cell-based smears (frosted ends, labels) are covered in Cytology Slides.
Tissue sections
When the specimen is solid tissue, it cannot simply be pressed flat. Columbia’s histology laboratory describes the sequence. The tissue is fixed, then embedded: dehydration in alcohols and infiltration with paraffin, or a similar agent. Sections 3 to 10 microns thick are then cut on steel knives in a microtome with a precise mechanical advance, and each section is mounted on a glass slide and covered with a thin cover glass. Because the cut section is nearly colourless, it needs differential staining so its components can be recognised. For the instrument itself, see What Is a Microtome?
The University of Iowa Central Microscopy Research Facility describes how sections get from the cutting stage onto glass in a core-facility setting. Sections are laid on a warm water bath at 45 to 55 degrees Celsius and picked up onto a slide, then the slides are warmed flat on a warming tray until all moisture is gone between the slide and the section. It gives light-level section thickness as 1 to 10 microns, recommends high-quality slides, and notes that some slides are ionically charged. The CDC exercise, by contrast, is a clinical-laboratory teaching exercise and never mentions a water bath: the two settings prepare different kinds of specimens on the same piece of glass.
Mounting medium
Columbia describes a mounting medium as a transparent substance that hardens and seals the preparation, and says it must have a refractive index similar to that of the glass slide and coverslip. The refractive-index requirement is the reason a mounted section can look clear under the objective: a medium that differs greatly from glass would bend light at the boundaries and blur the image.
Choose the preparation by what you need to see
The sources support a simple decision aid, built from the purposes of each route rather than from any single source’s ranking.
- Live organisms or motion: use a wet mount and read it immediately at 40X, as the CDC exercise does for Trichomonads.
- Fungal elements such as yeast or pseudohyphae: the CDC exercise uses a KOH mount and looks for 2 to 6 µm yeast cells and 20 to 100 µm pseudohyphae.
- A stable, stainable layer of cells: make a smear and fix it, by heat or methanol in the CDC exercise, with chemical fixatives often preferable for tissue specimens according to LibreTexts.
- Internal architecture of tissue: fix, embed in paraffin, section at 3 to 10 microns on a microtome, mount and stain, as Columbia describes.
Labeling, handling and disposal
The CDC exercise is explicit about slide handling in a laboratory. Its materials list calls for frosted-edge microscope slides, a pencil or wax pencil, cover slips, sterile loops, sterile pipettes, a slide rack and bibulous paper. Its waste guidance sends PPE, alcohol swabs and lens paper to a biohazard container, and sends microscope slides to a sharps container if they are discarded after examination. It also directs students to review PPE use before starting. A pencil-labeled frosted edge is the practical reason frosted slides appear in the list: the label stays attached through staining and solvent steps. Label options and their resistance to solvents are compared in Microscope Slide Labels.
Common mistakes
These points follow directly from what the sources say, not from outside rules of thumb.
- Treating a wet mount as a keepsake. It is not fixed and is read at once, so it is the wrong route if you need a slide to be stained or re-examined later.
- Using heat on tissue by default. LibreTexts says chemical fixatives are often preferable to heat for tissue specimens; heat fixation is described for smears.
- Skipping the drying step on a section. Iowa warms slides until all moisture is gone between the slide and the section.
- Ignoring refractive index in the mounting medium. Columbia says the medium must have a refractive index similar to glass.
- Discarding slides with ordinary waste. The CDC exercise sends discarded slides to a sharps container.
Frequently asked questions
What is the difference between a wet mount and a smear?
A wet mount keeps the specimen in a drop of liquid under a coverslip and is observed at once, so organisms stay live. A smear spreads a thin layer on the slide and fixes it, by brief heating or a chemical fixative, so the cells are attached and can be stained.
Why is fixation needed?
According to LibreTexts, fixation attaches cells to the slide, kills organisms and halts movement and metabolism while preserving cell components. Columbia describes it as retaining the characteristic shape and structure of the tissue.
How thick is a tissue section for light microscopy?
Columbia gives 3 to 10 microns for sections cut on a microtome, and the University of Iowa facility gives 1 to 10 microns as the light-level range.
Does the specimen need a coverslip?
In the wet mount, KOH mount and tissue-section routes described above, a coverslip is added. The CDC exercise lists cover slips in its materials, and Columbia describes tissue sections covered with a thin cover glass.
Sources
- CDC REACH, Routine Microscopy Procedures Student Laboratory Exercises: reach.cdc.gov (read 2026-11-15).
- Liu et al., Introduction to Microbiology, section 2.7, Sample Preparation for Microscopic Staining, LibreTexts, CC BY 4.0: bio.libretexts.org (read 2026-11-15).
- Columbia University histology laboratory, Histological Techniques: histologylab.ctl.columbia.edu (read 2026-11-15).
- University of Iowa Central Microscopy Research Facility: cmrf.research.uiowa.edu (read 2026-11-15).
Data: Four microscope slide preparation routes compared: fixation, support and size figures
Compares wet mount, KOH mount, heat or methanol fixed smear and paraffin tissue section by how the specimen is stabilised, how it sits on the slide and the size or thickness figures stated in a CDC training exercise and in university microbiology and histology teaching material.
| Preparation route | Fixation or stabilisation | How the specimen sits on the slide | Size or thickness figure stated |
|---|---|---|---|
| Wet mount | None; observed at once | Drop of liquid under a coverslip | Example organism Trichomonads about 15 µm (observed at 40X) |
| KOH mount | KOH added to the drop; observed at once | Drop of specimen plus KOH under a coverslip | Yeast 2-6 µm; pseudohyphae 20-100 µm (observed at 40X) |
| Smear | Heat fixation, or chemical fixative such as methanol | Thin layer spread on the slide | No figure stated |
| Paraffin tissue section | Fixation, then alcohol dehydration and paraffin infiltration | Microtome section mounted on glass, sealed with mounting medium and a thin cover glass | Sections 3-10 µm (Columbia); 1-10 µm light level (Iowa) |
Sources
- CDC REACH Routine Microscopy Procedures Student Laboratory Exercises (accessed 2026-11-15)
- LibreTexts Introduction to Microbiology 2.7 Sample Preparation for Microscopic Staining (accessed 2026-11-15)
- Columbia University histology laboratory, Histological Techniques (accessed 2026-11-15)
- University of Iowa Central Microscopy Research Facility (accessed 2026-11-15)
Compiled by CASRAI from the sources above. Free to reuse under CC BY 4.0 with attribution.







