Skip to main content
v2026.11,986 entries · CC-BY 4.0
LAC HealthSponsored

Shop pipette wipes supplies

  • FDA registered
  • ISO 13485
  • BBB Accredited A+

Shop at LAC Health

What Are Pipette Wipes? Types, Specifications, and Lab Use

A complete guide to pipette wipes: material types, IEST-RP-CC004.3 specifications, anti-static boxes, and proper tip-wiping technique to avoid volume errors.

Written and maintained by CASRAI Editorial Board

Published

On this page

Pipette wipes are low-lint, non-abrasive delicate task wipers engineered for laboratory environments to clean pipettor shafts, wipe fluid droplets from the exterior of pipette tips, and service sensitive optical instruments without shedding cellulose fibers or generating disruptive electrostatic charges. Manufactured from virgin wood pulp fibers or synthetic polymer blends, these specialty wipers possess high capillary absorbency and low extractable chemical profiles, preventing contamination during sensitive analytical assays, molecular biology protocols, and volumetric fluid transfers.

Who uses them: Research scientists, clinical laboratory technologists, analytical chemists, quality control specialists, and academic laboratory personnel utilize pipette wipes during daily liquid handling, equipment decontamination, and spectrophotometric sample preparation.

This page describes products and general use; it is not medical advice.

What it is

A pipette wipe, commonly classified in laboratory supply catalogs as a delicate task wiper, is a specialized light-duty absorbent sheet formulated for clean benches, analytical workstations, and diagnostic laboratories. Unlike standard paper towels or commercial facial tissues manufactured from recycled pulp bound with wet-strength resins and chemical softeners, laboratory pipette wipes are produced from 100% virgin wood fiber or synthetic filament webs. Their primary purpose is to provide immediate liquid sorption and particle containment while leaving negligible lint or chemical residues on critical apparatus.

In analytical liquid handling, pipetting accuracy depends on the physical condition of the pipette tip exterior as well as internal calibration. During aspiration, surface tension and viscous drag can cause micro-droplets or a thin liquid film to cling to the external polypropylene surface. If transferred into the receiving vessel, this extraneous liquid introduces a positive volumetric error, altering concentration calculations. Pipette wipes provide an absorbent, low-lint medium for removing these external droplets without abrading the tip cone or introducing airborne fibers that could contaminate reagent reservoirs or block microfluidic channels.

Beyond tip wiping, these wipes function as the primary dry cleaning substrate for laboratory pipettors. Mechanical air-displacement pipettors require surface decontamination to remove spilled buffers, biological fluids, or nucleic acids. Pipette wipes allow technicians to apply mild detergents, 70% isopropanol solutions, or decontaminating agents across the handle, volume adjustment collar, and tip ejector assembly without degrading the polymer housing or depositing fibers inside piston seals.

How it works or is built

The performance of laboratory delicate task wipes relies on specific manufacturing processes and mechanical design elements engineered to minimize particulate generation while maximizing fluid intake speed.

Raw Material and Fiber Architecture

The standard benchmark laboratory wipe is constructed from 100% virgin cellulose pulp processed through a Light Dry Crepe (LDC) papermaking technique. Virgin wood fibers provide uniform length, high purity, and inherent hydrophilicity. The dry creping process introduces microscopic folds across the sheet, imparting three essential characteristics:

  • Rapid Capillary Uptake: The micro-crevices generate capillary draw, pulling aqueous buffers, saline solutions, and organic solvents into the internal fiber matrix within fractions of a second.
  • Surface Softness: Mechanical creping eliminates rigid fiber edges, preventing the wipe from scratching delicate optical coatings on spectrophotometer cuvettes, microscope objectives, or analytical balance draft shields.
  • Reduced Fiber Breakage: By avoiding recycled fiber fragments, the sheet retains structural integrity when pulled across laboratory surfaces, substantially reducing fiber shedding.

Anti-Static Dispensing System

Electrostatic discharge (ESD) presents challenges in analytical workflows. Pulling a dry paper sheet from a carton generates static charge through friction. In an analytical laboratory, a charged wipe can induce drift on high-precision analytical balances reading to 0.01 mg. Furthermore, electrostatic charges attract airborne dust particles directly to the wipe surface and can cause droplet deflection when handling low-volume pipetting tips.

To overcome this issue, delicate task wipes are packaged in Pop-Up dispenser boxes equipped with an integrated anti-static poly-shield (such as the LintGuard barrier). This polymer shield covers the dispensing aperture. As each sheet is pulled through, the poly-shield reduces triboelectric charge accumulation, controls dispensing velocity to prevent fiber tearing, and physically shields the remaining sheets inside the box from settling dust, ambient aerosols, and moisture fluctuations.

Ply Configurations

Laboratory wipes are produced in single-ply (1-ply) and two-ply (2-ply) formats. Single-ply wipes provide high tactile sensitivity and low material volume, making them ideal for precise manipulation around narrow pipette tips and delicate micro-electrodes. Two-ply wipes laminate two creped sheets together, creating internal air pockets that dramatically increase total sorptive fluid capacity, making them favored for benchtop spill containment, cleaning centrifuge rotors, and scrubbing larger pipettor manifolds.

Types and variants

Laboratories select wiping materials based on cleanliness classifications, chemical compatibility, and specific analytical requirements. The table below outlines the primary variants of laboratory wipes used across research, clinical, and industrial facilities.

Wiper Classification Primary Material Composition Cleanroom Compatibility Typical Laboratory Application Key Performance Differentiator
Standard Delicate Task Wipe (1-Ply) 100% Virgin Wood Pulp Cellulose Controlled Environments / ISO Class 7–8 Wiping pipette tips, cuvettes, microscope slides, and balance pans High tactile sensitivity, rapid aqueous absorbency, low cost
Heavy-Duty Delicate Task Wipe (2-Ply) 100% Virgin Wood Pulp Cellulose (Laminated) Controlled Environments / ISO Class 7–8 Cleaning pipettor bodies, solvent spills, and centrifuge buckets Double fluid holding capacity, higher wet burst strength
Hydroentangled Nonwoven Wipe 55% Cellulose / 45% Polyester Blend ISO Class 5–6 (Class 100–1,000) Aseptic hoods, biosafety cabinets, and cell culture suites High tensile strength, low particulate release, solvent durability
Continuous Filament Knitted Wiper 100% Synthetic Polyester (Double-Knit) ISO Class 3–4 (Class 1–10) Semiconductor labs, mass spectrometry ion sources, microelectronics Ultrasonic or laser-sealed borders, near-zero lint and extractables
Pre-Saturated Disinfectant Wipe Polypropylene or Polyester with 70% IPA / 30% DI Water ISO Class 5–7 Daily pipettor barrel wipe-down and bio-decontamination Ready-to-use, standardized solvent dosage, zero aerosol generation

In standard molecular biology and clinical diagnostic laboratories, 100% virgin cellulose delicate task wipes represent the universal benchmark. In contrast, cleanroom production suites, microfluidic fabrication facilities, and trace-metal analytical laboratories require hydroentangled or knitted continuous-filament wipes tested under cleanroom protocols.

Sizes or specifications that matter

Selecting the appropriate wipe format ensures operational efficiency while minimizing consumable waste. Laboratory delicate task wipes are standardized into distinct physical dimensions and packaging configurations.

Standard Format Dimensions (Inches) Dimensions (Centimeters) Packaging Configuration Primary Intended Workstation
Small Bench Format (1-Ply) 4.4 × 8.4 in 11.1 × 21.3 cm 286 sheets/box (60 boxes/case) Individual pipetting stations, balance tables, microscope benches
Medium Format (1-Ply) 11.2 × 12.3 in 28.4 × 31.2 cm 196 sheets/box (15 boxes/case) Fume hoods, chemical synthesis benches, rotary evaporators
Large Format (1-Ply) 14.7 × 16.6 in 37.3 × 42.1 cm 140 sheets/box (15 boxes/case) Equipment maintenance, benchtop liners, large apparatus cleaning
Medium 2-Ply Format 11.8 × 11.8 in 30.0 × 30.0 cm 90 sheets/box (15 boxes/case) Cell culture suites, biological safety cabinet sanitization

Laboratory engineers evaluate several technical performance metrics defined under Institute of Environmental Sciences and Technology standards, specifically IEST-RP-CC004.3 (Evaluating Wiping Materials Used in Cleanrooms and Other Controlled Environments):

  • Basis Weight: Standard single-ply cellulose delicate task wipes measure approximately 17.8 g/m², whereas heavy-duty nonwoven cleanroom wipes range from 65 to 160 g/m².
  • Sorptive Capacity: The volume of liquid a wiper absorbs per unit area (mL/m²). Cellulose exhibits intrinsic water absorption of 100 to 120 mL/m², while hydroentangled polyester/cellulose blends achieve over 300 mL/m².
  • Sorptive Rate: High-quality delicate task wipes achieve absorption rates under 0.5 seconds, ensuring instantaneous droplet capture.
  • Particulate and Lint Generation: Virgin cellulose delicate wipes typically release fewer than 20 particulates greater than 50 µm per standard Gelbo lint cycle, representing an extra-low-lint profile.
  • Extractable Contaminants: Measured gravimetrically as non-volatile residue (NVR in g/m²) and ion chromatography for trace inorganic ions. Pure virgin cellulose produces low extractables in water, though aggressive solvents can extract residual lignins during prolonged immersion.

As summarized in the data table below, laboratory wiping materials vary substantially in basis weight, sorptive capacity, and particulate generation across different fiber structures.

How to choose

Selecting the correct wipe requires aligning wiper properties with experimental sensitivity, reagent chemistry, and facility standards.

1. Analytical Sensitivity and Particle Tolerance

For standard liquid handling, routine chemical titrations, and clinical sample preparation, single-ply virgin cellulose wipes provide an ideal balance of absorbency and economy. However, in trace-metal analysis, high-performance liquid chromatography (HPLC), or mass spectrometry (LC-MS), cellulose fibers can introduce particulate blockages or ionic contamination (such as sodium and calcium leaching). In these environments, laboratories must specify continuous-filament polyester knitted wipers laundered in deionized water.

2. Chemical and Solvent Compatibility

Reagent compatibility dictates wipe selection:

  • Aqueous Buffers and Alcohols (70% IPA, Ethanol): Virgin cellulose wipes provide rapid wetting, high absorption, and full stability during surface disinfection.
  • Aggressive Organic Solvents (Acetone, Chloroform): Pure cellulose maintains structural integrity because it lacks synthetic binders. However, nonwoven blended wipes containing chemical adhesives must be avoided, as solvents can leach binders into analytical samples.
  • Bleach (Sodium Hypochlorite Solutions): Cellulose degrades when exposed to strong oxidizing bleaches. Polypropylene or polyester wipes offer superior resistance for aggressive hypochlorite decontamination.

3. Static Sensitivity and Sterility

When placing wipes near microbalances or automated liquid handlers, always specify anti-static Pop-Up boxes to avoid electrostatic drift. Furthermore, standard delicate task wipes are supplied non-sterile. For use inside laminar flow hoods during cell culture or microbiological manipulations, sterile gamma-irradiated wipes or autoclaved nonwoven wipes are required, as detailed in our guide on aseptic technique in the lab.

Safe use and handling basics

Proper technique when using pipette wipes is essential to safeguard measurement precision, prevent cross-contamination, and preserve equipment longevity.

The Physics of Tip Wiping: Avoiding Capillary Wicking

The most critical operational rule when handling liquid pipettors is the prevention of capillary wicking. International standards for piston-operated volumetric apparatus (ISO 8655-2) emphasize that the pipette and the tip function as a single integrated volumetric system. When aspirating liquid, proper technique minimizes droplet formation on the outside of the tip. Adhering to validated pipetting technique best practices—such as maintaining vertical aspiration, immersing the tip only 2 to 3 mm below the liquid meniscus, and pausing briefly before withdrawal—reduces external clinging liquid.

When handling viscous samples or volatile liquids, external droplets frequently accumulate. When removing these droplets, follow this strict protocol:

  1. Do Not Touch the Orifice: Never bring the wipe into contact with the opening (orifice) at the distal end of the pipette tip. Dry cellulose exerts massive capillary suction pressure. If the wipe touches the orifice, it immediately wicks liquid out from inside the tip lumen, causing an uncalibrated negative volumetric error of up to 2% to 3% or more.
  2. Wipe Downward Along the Barrel: If exterior wiping is required, hold the wipe gently against the upper polypropylene tip wall and draw it downward toward the tip, stopping several millimeters before the orifice.
  3. Prefer Vessel-Wall Touching Off: Under standard operating procedures, touching the tip against the inner wall of the liquid container at a 10° to 45° angle over a distance of 8 to 10 mm (the “touching off” method) is the preferred technique for removing exterior droplets without risking capillary loss. Reserve physical wiping for viscous fluids where wall touching is insufficient.
  4. Use Reverse Pipetting for Challenging Liquids: When dispensing viscous or detergent-rich solutions prone to external droplet retention, consider utilizing reverse pipetting rather than excessive physical wiping, which delivers a calibrated aliquot while retaining excess sample in the tip.

Pipette Body Cleaning and Maintenance Protocol

Routine surface decontamination maintains hygiene and prevents sample-to-sample carryover across laboratory shared equipment. Technicians using manual or electronic pipettors, as well as those operating volumetric transfer devices described in our review of pipette pumps, should execute a standardized weekly cleaning routine:

  1. Disassembly: Remove the disposable tip and tip ejector sleeve according to the manufacturer instruction manual.
  2. Solvent Application: Moisten a fresh delicate task wipe with 70% isopropanol or a laboratory disinfectant. Never submerge the entire pipettor body in liquid unless specifically rated as fully autoclavable and submersible.
  3. Surface Wiping: Gently wipe down the outer handle, finger rest, volume adjustment dial, and digital display window. Use a fresh wipe to clean the tip cone (shaft), ensuring all dried buffer salts or biological residues are dissolved and removed.
  4. Inspection: Check that no loose fibers from the wipe remain lodged around the internal O-ring or tip cone seal. Accumulated fibers create microscopic air pathways that disrupt vacuum formation, causing pipettes to fail gravimetric calibration tests under ISO 8655-6.
  5. Drying: Allow the pipettor components to air-dry completely before reattaching the tip cone and ejector sleeve.

Optical and Glassware Cleaning

When cleaning optical cuvettes, refractometer prisms, or glassware such as a Class A volumetric pipette, always fold the delicate task wipe to expose a clean, unused surface for each stroke. Wiping optical glass with a contaminated wipe causes micro-abrasions on quartz surfaces, increasing stray light scatter and degrading spectrophotometric absorbance measurements.

Common mistakes

Recognizing and rectifying common errors ensures reproducible experimental data:

1. Touching the Tip Orifice During Wiping

The most widespread technical error is dabbing or wiping across the tip aperture. Capillary action instantly siphons sample volume out of the tip, resulting in significant under-delivery. Always maintain clearance between the absorbent wipe and the tip opening.

2. Using Standard Facial Tissues or Utility Paper Towels

Substituting commercial facial tissues or brown paper towels for certified laboratory wipes is severe laboratory malpractice. Consumer tissues contain high levels of recycled fiber dust, mineral fillers, and chemical binders. These fibers shed rapidly, clog micro-pipette orifices, contaminate PCR mixtures with exogenous nucleases, and scratch delicate optical glass.

3. Reusing Wipes Across Multiple Samples

Attempting to economize by using a single wipe for multiple pipette tips or cleaning tasks introduces severe cross-contamination risks. A wipe that has absorbed a droplet of concentrated salt solution, radioactive tracer, or DNA template will transfer residual molecules to subsequent surfaces. Delicate task wipes are single-use consumables designed to be discarded immediately after each discrete wiping operation.

4. Disregarding Static Charges Near Microbalances

Pulling wipes rapidly from a standard non-shielded container adjacent to an analytical balance generates static fields that cause balance readouts to fluctuate uncontrollably. Always utilize anti-static poly-shield dispenser boxes, position wipe boxes at least 30 cm away from balance draft shields, and allow static charges to dissipate before recording gravimetric readings.

5. Vigorous Rubbing on Coated Optical Surfaces

Although virgin cellulose wipes are non-abrasive, applying excessive downward pressure when cleaning anti-reflective optical coatings, spectrophotometer mirrors, or microscope objectives can drag particulate dust particles across the glass, causing scratches. Always apply gentle, single-directional wiping strokes with minimal pressure.

Frequently asked questions

Can you wipe a pipette tip with a regular tissue or paper towel?

No, standard paper towels and facial tissues shed heavy lint and contain recycled fiber dust, mineral fillers, and chemical binders. These particulates contaminate reagents, introduce airborne dust, scratch delicate optical surfaces, and clog micro-bore pipette tips.

Why must you avoid touching the pipette tip orifice when wiping?

Touching the open orifice of a pipette tip with an absorbent wipe triggers capillary wicking. The dry porous fiber matrix siphons liquid out of the tip lumen, producing systematic negative volumetric delivery errors of 2% to 3% or more.

What is the difference between 1-ply and 2-ply delicate task wipes?

Single-ply (1-ply) wipes provide high tactile flexibility and precision for handling small items like pipette tips and micro-electrodes. Two-ply (2-ply) wipes laminate two sheets together with internal air pockets, doubling fluid absorption capacity for cleaning larger pipettor bodies and benchtop spills.

How do anti-static poly-shield dispenser boxes work?

Anti-static dispenser boxes incorporate a polymer barrier over the dispensing aperture (such as LintGuard). This shield reduces triboelectric friction that generates static electricity during withdrawal, prevents sheet tearing, and blocks ambient laboratory dust from settling onto unused wipes inside the box.

Are pipette wipes compatible with laboratory solvents like acetone and bleach?

Pure virgin cellulose wipes withstand water, alcohols, dilute acids, and acetone without dissolving. However, strong oxidizing bleaches gradually weaken cellulose fibers, and trace-analysis workflows requiring aggressive solvents are better served by 100% continuous-filament polyester wipes that contain zero extractable organic compounds.

When should you touch off against the vessel wall instead of using a wipe?

Under ISO 8655 guidelines, touching off against the vessel wall is the standard method for removing excess liquid from the outside of a pipette tip when handling aqueous solutions. Delicate task wipes should be reserved for viscous or foaming fluids where wall touching is insufficient, and wiping must always avoid contacting the tip orifice.

Sources

  • Kimberly-Clark Professional. Kimtech Science Kimwipes Delicate Task Wipers Technical Data Sheet (SKU 34155). https://www.kcprofessional.com/en-us/products/scientific-and-research/wipers/delicate-task-wipes/kimtech-science-kimwipes-delicate-task-wipers/34155 (Accessed 2026-11-14)
  • Gilson, Inc. Gilson Guide to Pipetting: Best Practices for Liquid Handling Accuracy and Precision. https://www.gilson.com/default/pipette-guide (Accessed 2026-11-14)
  • International Organization for Standardization. ISO 8655-2:2022 Piston-Operated Volumetric Apparatus — Part 2: Pipettes. https://www.iso.org/standard/64104.html (Accessed 2026-11-14)
  • Texwipe. Cleanroom Wipers Technical Specifications and Sorbency Standards (TX609 and TX1009). https://www.texwipe.com/cleanroom-wipers (Accessed 2026-11-14)
  • Institute of Environmental Sciences and Technology. IEST-RP-CC004.3: Evaluating Wiping Materials Used in Cleanrooms and Other Controlled Environments. https://www.iest.org/Standards-RPs/Recommended-Practices/IEST-RP-CC004 (Accessed 2026-11-14)
  • Eppendorf SE. Proper Pipetting Techniques and Pipette Decontamination Guidelines. https://www.eppendorf.com/pipetting-technique (Accessed 2026-11-14)

Data: Laboratory Wiping Materials Performance Comparison

Comparative performance metrics of laboratory and cleanroom wiping materials compiled from manufacturer technical data sheets (Kimberly-Clark Professional, Texwipe) and IEST-RP-CC004.3 test standards.

Period covered: 2024/2026. Coverage: Global.

Laboratory Wiping Materials Performance Comparison
Wiper ClassificationBase MaterialBasis Weight (g/m²)Sorptive Capacity (mL/m²)Sorptive Rate (s)Liquid Particle Count (≥0.5 µm) (10⁶ particles/m²)
Delicate Task Tissue (1-Ply)100% Virgin Wood Fiber (LDC Crepe)17.81100.420
Delicate Task Tissue (2-Ply)100% Virgin Wood Fiber (LDC Crepe)35.62150.425
Hydroentangled Nonwoven55% Cellulose / 45% Polyester693200.372
Continuous Filament Knit100% Polyester Double-Knit Interlock1585300.58.4
Microfiber Cleanroom Wiper70% Polyester / 30% Polyamide Split853800.512

Sources

Compiled by CASRAI from the sources above. Free to reuse under CC BY 4.0 with attribution.

Follow CASRAI

Research-administration guidance, standards updates and independent tool reviews.

Ask CASRAI · free to try

Ask about What Are Pipette Wipes? Types, Specifications, and Lab Use

2 free questions a day, no account.

An AI assistant for research: funder rules, compliance, methods and publishing. It links the sources behind its answers and labels answers that come from a web search.

Answers draw on CASRAI's guides and dictionary plus the federal and funder documents we index: Federal Register, Grants.gov, Regulations.gov and UKRI.

Works on this site and inside Claude, Cursor and the AI tools you already use.

Everything CASRAI publishes — this page, the dictionary, the guides and the news — stays open to read, with no account and no card.

Referenced across the research world

University of Cambridge logoColumbia University logoCrossref logoUniversity of Edinburgh logoHarvard University logoUniversity of Oxford logoPrinceton University logoStanford School of Medicine logoUniversity College London logoORCID logoUniversity of Cambridge logoColumbia University logoCrossref logoUniversity of Edinburgh logoHarvard University logoUniversity of Oxford logoPrinceton University logoStanford School of Medicine logoUniversity College London logoORCID logo
  • University of Cambridge logo
  • Columbia University logo
  • Crossref logo
  • University of Edinburgh logo
  • Harvard University logo
  • University of Oxford logo
  • Princeton University logo
  • Stanford School of Medicine logo
  • University College London logo
  • ORCID logo

View CASRAI adoption →