Skip to main content
v2026.11,986 entries · CC-BY 4.0
LAC HealthSponsored

Shop kevlar gloves supplies

  • FDA registered
  • ISO 13485
  • BBB Accredited A+

Shop at LAC Health

Kevlar Gloves: What the Fiber Means and What the Cut Rating Tells You

Kevlar is a fiber, not a cut level. See how ANSI/ISEA 105 levels A1-A9 and OSHA 1910.138 task evaluation decide which protective glove fits a hazard.

Written and maintained by CASRAI Editorial Board

Published · Last updated

This page describes products and general use; it is not medical advice.

On this page

Short answer: Kevlar is the name of a fiber, not a glove rating. A glove that contains Kevlar-brand fiber is still judged by its ANSI/ISEA 105 cut level (A1 to A9) and by the hazards of the task. Who uses this page: safety officers, clinic and lab staff, and buyers checking what “Kevlar gloves” does and does not tell them.

What Kevlar gloves are

Kevlar is a brand of fiber described on the Arclin Kevlar brand page as a “heat-resistant, synthetic, lightweight fiber that delivers high tensile strength.” The same page lists cut protection among its applications and says its cut- and heat-resistant technology for personal protective equipment (PPE) meets or exceeds international standards for protection and performance. A Kevlar glove is therefore a protective glove in which that fiber is part of the fabric. The fiber name alone does not state how much cutting a given glove withstands; that is what the cut level is for.

Kevlar is the fiber, A1-A9 is the rating

The Industrial Safety Equipment Association (ISEA) describes ANSI/ISEA 105-2024, the American National Standard for Hand Protection Classification, as a “comprehensive classification system for hand and arm protection, including gloves and sleeves.” Its cut levels run from A1 to A9. ISEA summarises them this way:

ANSI/ISEA 105 cut level What ISEA says it protects against
A1, A2, A3 Scrapes
A4, A5, A6 Cuts for which stitches would be required
A7, A8, A9 Brutal or extreme injuries

Source: ISEA hand protection page (checked 2026-10-30). For the full A1-A9 breakdown, see the CASRAI guide to cut-resistant glove levels.

Materials in protective gloves

ISEA lists protective gloves as “fabric or coated fabric; leather, canvas, or metal mesh”. A Kevlar glove belongs to the fabric group. Within that group, the material is only one input; the rating on the glove is what tells you the tested cut level.

How to choose

The only selection rule stated by a primary source here comes from OSHA. 29 CFR 1910.138(a) requires employers to “select and require employees to use appropriate hand protection when employees’ hands are exposed to hazards such as those from skin absorption of harmful substances; severe cuts or lacerations; severe abrasions; punctures; chemical burns; thermal burns; and harmful temperature extremes.” Paragraph (b) says selection must be based on “an evaluation of the performance characteristics of the hand protection relative to the task(s) to be performed, conditions present, duration of use, and the hazards and potential hazards identified.” In practice that means starting from the task and its hazards, then checking the glove’s marked performance, rather than starting from a fiber name. Source: OSHA 29 CFR 1910.138 (checked 2026-10-30).

Safe use and handling basics

  • Match the glove to the hazard named in your task evaluation (cuts, abrasion, punctures, heat, chemicals), as 1910.138 requires.
  • Do not treat a cut rating as protection against every hazard. ISEA notes that “not all puncture-resistant gloves protect against needle sticks.”
  • Follow the glove maker’s instructions for use for any limits the maker states.

Common mistakes

  • Assuming “Kevlar” means a specific cut level. The level is a property of the tested glove, not of the fiber name.
  • Assuming a cut-resistant glove also protects against needle sticks or chemicals. Those are separate hazards in 1910.138(a).
  • Skipping the task evaluation that 1910.138(b) calls for.

FAQ

Are Kevlar gloves cut-proof?

No glove is described as cut-proof by the standards cited here. ANSI/ISEA 105 classifies gloves from A1 (scrapes) to A9 (brutal or extreme injuries), so the question to ask is which level and which hazard, not whether a glove is proof against cuts.

Does Kevlar mean a glove is A9?

No. Kevlar names a fiber. The cut level comes from the ANSI/ISEA 105 classification of the specific glove.

How do I pick between cut-resistant gloves?

Under OSHA 29 CFR 1910.138(b), base the choice on the task, conditions, duration of use and identified hazards. See also our comparison of nitrile, latex and vinyl gloves for disposable glove materials and the lab safety equipment checklist.

Sources

Follow CASRAI

Research-administration guidance, standards updates and independent tool reviews.

Ask CASRAI · free to try

Ask about Kevlar Gloves: What the Fiber Means and What the Cut Rating Tells You

2 free questions a day, no account.

An AI assistant for research: funder rules, compliance, methods and publishing. It links the sources behind its answers and labels answers that come from a web search.

Answers draw on CASRAI's guides and dictionary plus the federal and funder documents we index: Federal Register, Grants.gov, Regulations.gov and UKRI.

Works on this site and inside Claude, Cursor and the AI tools you already use.

Everything CASRAI publishes — this page, the dictionary, the guides and the news — stays open to read, with no account and no card.

Referenced across the research world

University of Cambridge logoColumbia University logoCrossref logoUniversity of Edinburgh logoHarvard University logoUniversity of Oxford logoPrinceton University logoStanford School of Medicine logoUniversity College London logoORCID logoUniversity of Cambridge logoColumbia University logoCrossref logoUniversity of Edinburgh logoHarvard University logoUniversity of Oxford logoPrinceton University logoStanford School of Medicine logoUniversity College London logoORCID logo
  • University of Cambridge logo
  • Columbia University logo
  • Crossref logo
  • University of Edinburgh logo
  • Harvard University logo
  • University of Oxford logo
  • Princeton University logo
  • Stanford School of Medicine logo
  • University College London logo
  • ORCID logo

View CASRAI adoption →