Skip to main content
v2026.11,986 entries · CC-BY 4.0
LAC HealthSponsored

Shop p10 pipette supplies

  • FDA registered
  • ISO 13485
  • BBB Accredited A+

Shop at LAC Health

P10 Pipette: Volume Range, Tips and Safe Use

A P10 pipette handles volumes up to 10 µL. Compare documented ranges, tips, display conventions and manufacturer error limits.

Written and maintained by CASRAI Editorial Board

Published

On this page

A P10 pipette is a small-volume laboratory micropipette with a maximum setting of 10 µL. Its lower limit depends on the model: BT Lab Systems specifies 0.5–10 µL for its P10, while Addgene’s training chart lists P10 use at 1–10 µL. Match the instrument’s documented range, tips and error limits to the transfer.

Who uses it: researchers, laboratory technicians and trainees measuring small liquid volumes at the bench. A P10 belongs to the broader family of piston-operated micropipettes, but its capacity requires particular attention to decimal places and model-specific specifications.

What a P10 pipette is and what it does

A P10 measures and transfers a selected microliter-scale volume through a disposable tip. The model designation identifies a capacity class; the volume display shows the actual setting. These are different pieces of information: an adjustable P10 can be set below its maximum, within the range its manufacturer permits.

For a concrete example, BT Lab Systems identifies its BT1501 as a single-channel, variable-volume P10 with a click-stop adjustment system. Addgene places the P10 between the smaller P2 and the larger P20 in its pipette-selection chart. That chart is useful for recognizing the family, while the instrument’s own specification determines its operating limits.

The distinction matters when a method calls for less than 1 µL. A general chart and a manufacturer’s model-specific range answer different questions. Neither the letters P10 nor the presence of a small number on the display establishes that a particular instrument is suitable for every sub-microliter transfer.

Keep the unit visible when identifying equipment. Gilson’s guide distinguishes the P10 from its P10mL model. Ten milliliters equals 10,000 µL, so these maximum capacities differ by a factor of 1,000. A label or equipment request that drops the unit can therefore describe a very different instrument.

How it works: piston, air cushion and disposable tip

In an air-displacement pipette, the piston moves air above the liquid in the tip. Thermo Fisher Scientific describes the volume setting as determining the piston’s position. During forward pipetting, pressing to the first stop displaces the set volume of air; releasing the button with the tip immersed draws liquid into the tip. Dispensing uses the first stop and then the second, blow-out stop.

The second stop therefore has a separate function from the measuring stroke. Treating both stops as interchangeable changes the operation. This explanation describes ordinary forward pipetting; alternative techniques have their own instructions and should not be assembled by mixing parts of different methods.

The visible parts include a plunger, volume adjustment, display, shaft or tip holder, and tip ejector. Rainin’s Classic manual describes a micrometer controlling piston stroke, a stainless-steel piston and an O-ring seal. These components explain why the tip’s airtight connection matters: it completes the working air-displacement system. Materials and service arrangements belong to the particular model.

Types and variants around the 10 µL capacity

A variable-volume P10 is one option for this capacity. Fixed-volume and multichannel instruments also exist at 10 µL. Eppendorf’s Research plus manual documents the following configurations; its product names differ from the P10 label used by other manufacturers.

Type Typical use Key difference and source
Adjustable single-channel One transfer at a selected volume Research plus 0.5–10 µL; one tip. Eppendorf operating manual, ordering information.
Fixed-volume single-channel Transfers at the same specified volume Research plus fixed 10 µL; no choice of transfer volume. Eppendorf operating manual, ordering information.
Adjustable multichannel Repeated transfers into a plate Research plus 8- or 12-channel 0.5–10 µL models, with 9 mm cone spacing for 96-well plates. Eppendorf operating manual, ordering information.

Channel count and capacity describe separate features. For the broader distinction between tube work and plate work, see single-channel and multichannel micropipettes. A shared maximum capacity does not establish identical performance specifications.

Sizes and specifications that matter

Read the operating range, adjustment increment and error limits separately. BT’s published single-channel specifications give a useful size comparison within one manufacturer’s range:

BT Lab Systems model Volume range Adjustment increment Source
P10 / BT1501 0.5–10 µL 0.1 µL BT P10 specification table
P20 / BT1505 2–20 µL 0.1 µL BT P10 specification table
P100 / BT1502 10–100 µL 0.5 µL BT P10 specification table

An increment describes the change available through the adjustment mechanism. It does not state how close the delivered volume will be to that setting. Thermo Fisher distinguishes accuracy, or closeness to the intended volume, from precision, or consistency among repeated transfers. A repeatable result can still have an incorrect mean.

The data table below compares manufacturer-published error specifications at a 10 µL test volume for BT’s P10 and Eppendorf’s single- and multichannel models. It expresses BT’s percentages in microliters to make the units comparable. These are specifications under the manufacturers’ test conditions, rather than results from a common comparative experiment.

BT states that its micropipette is calibrated according to EN ISO 8655 and supplied with a calibration report. Keep that report distinct from a product specification: the specification describes the model’s stated performance limits, while the supplied report accompanies the individual instrument. The manufacturer’s statement is the basis for the standards reference here; it does not establish an independent certification claim or a universal service interval.

A worked example: converting a percentage specification

BT lists ±1.0% inaccuracy at 10 µL. Converting that percentage gives 10 × 1.0 ÷ 100 = ±0.10 µL. Its 0.8% imprecision converts to 10 × 0.8 ÷ 100 = 0.08 µL. Keep the labels separate: the second number describes variability, not another allowance to add automatically to the first.

As an illustrative arithmetic example, a hypothetical deviation of 0.10 µL is 1% of a 10 µL transfer but 10% of a 1 µL transfer. This is not a measured result or a tolerance for either setting. It shows why a percentage must stay attached to its test volume; a figure quoted at maximum capacity cannot simply be assigned to a smaller transfer.

Reading the volume on a P10 pipette

Read the decimal convention for the exact instrument before interpreting the digits. Gilson’s PIPETMAN guide uses black and red numbers to indicate decimal position according to the model. Rainin’s Classic instructions also distinguish the significance of digits by capacity. Eppendorf’s Research plus uses a white separator to mark the decimal place.

Those differences make a memorized three-digit string an unreliable instruction across a mixed pipette fleet. Write the intended volume with its unit, identify the instrument, and interpret its display using the relevant manual. A transcription such as “set to 100” leaves out the very information needed to distinguish whole microliters from decimal fractions.

Addgene illustrates this problem across pipette sizes: its P20 example displays 100 for 10 µL, whereas its P2 example displays 100 for 1 µL. Those are examples for those instruments, not a P10 setting rule. Do not transfer a display convention merely because the instruments look alike.

How to choose the pipette and matching tips

Start with the required transfer volume and the documented range. Addgene advises using the appropriate pipette and tips and staying within the maximum setting. If two instruments cover a volume, compare their specifications at that volume rather than assuming that their names establish equivalent accuracy.

Next consider the liquid. Thermo Fisher’s sample-type guidance pairs aqueous buffers and diluted salt solutions with air displacement, standard tips and forward pipetting. It lists additional combinations for viscous liquids, including positive displacement and reverse techniques. Its mechanism guide explains the distinction: a positive-displacement piston contacts the liquid directly, without an intervening air cushion.

A P10 capacity designation does not resolve that liquid-handling choice. Temperature, atmospheric pressure, specific gravity and viscosity can affect air-displacement performance. Select the instrument and technique specified for the actual liquid and method, rather than treating the displayed volume as the only relevant property.

For Gilson’s PIPETMAN P10, the manual names D10, DL10, DF10ST and DFL10ST tips. This is a model-specific compatibility list, not a universal list for all P10 instruments. CASRAI’s pipette tip selection guide explains the wider consumable categories; the manufacturer’s compatibility instructions decide the fit.

Safe use, handling and care basics

Follow the manufacturer’s instructions for tip attachment and movement. Rainin specifies only enough mounting force to establish an airtight seal and gives a 1–2 mm immersion depth for its 10 µL Classic model. That depth is attached to that model; a general instruction to immerse every pipette by the same amount loses useful specificity.

Thermo Fisher advises consistent position, immersion depth and plunger speed for parallel samples. It also warns against laying a pipette on its side while liquid remains in the tip, because liquid can enter the instrument. Use the ejector to remove used tips and store the instrument upright on a stand. Disposable tips should not be washed for reuse.

Cleaning and sterilization instructions also have a defined scope. Rainin’s Classic manual identifies its shaft and tip ejector as autoclavable components. That statement does not authorize autoclaving the complete assembled pipette. Keep the component names, permitted treatment and exact model together when applying a cleaning instruction.

Gilson cautions against self-disassembly of P2 and P10 models because of their miniaturized parts. It recommends maintenance and calibration at least annually, with greater frequency according to use. For the distinction between a performance check and a service intervention, see pipette calibration and verification.

Common mistakes and what to check

Assuming every P10 has the same lower limit. Compare the range in the instrument’s documentation with the intended volume. The difference between BT’s 0.5–10 µL specification and Addgene’s 1–10 µL training chart is a reason to identify the model, not to stretch a range by habit.

Confusing resolution with accuracy. A small adjustment step is a control feature. It does not replace the systematic and random error specifications. Keep the test volume, units, tip system and channel configuration with any performance figure.

Treating a stable series as proof of correct delivery. Thermo Fisher’s accuracy/precision examples show that tightly grouped results can still miss the intended volume. Reproducibility alone cannot establish that the setting and delivered amount agree.

Ignoring temperature differences. Thermo Fisher identifies the temperature difference between liquid and instrument as an important influence on air-displacement accuracy: the intervening air can expand or contract. The underlying issue is the measuring system’s behavior, even when the digits remain unchanged.

Extending maintenance instructions beyond their scope. A component’s autoclave permission or another model’s disassembly procedure is not a general property of the P10 name. Use the actual instrument’s instructions and service route.

Sources

Data: Published error limits at a 10 µL test volume

Original compilation of BT Lab Systems P10 and Eppendorf Research plus single- and multichannel specifications. BT inaccuracy and imprecision percentages are converted to microliters at 10 µL; Eppendorf systematic and random errors are transcribed in microliters. Values describe each manufacturer’s own test conditions and are not results of comparative testing.

Published error limits at a 10 µL test volume
Instrument configurationTest volume (µL)Inaccuracy or systematic error limit (µL)Imprecision or random error limit (µL)Source location
BT Lab Systems P10 BT1501, single-channel100.10.08BT P10 page: Single Channel Pipette Specifications, BT1501, 10 µL test row
Eppendorf Research plus 0.5–10 µL, single-channel100.10.04Research plus Operating Manual, p.55, variable single-channel 0.5–10 µL
Eppendorf Research plus 0.5–10 µL, 8-/12-channel100.20.1Research plus Operating Manual, p.57, fixed cone spacing 0.5–10 µL

Sources

Compiled by CASRAI from the sources above. Free to reuse under CC BY 4.0 with attribution.

Follow CASRAI

Research-administration guidance, standards updates and independent tool reviews.

Ask CASRAI · free to try

Ask about P10 Pipette: Volume Range, Tips and Safe Use

2 free questions a day, no account.

An AI assistant for research: funder rules, compliance, methods and publishing. It links the sources behind its answers and labels answers that come from a web search.

Answers draw on CASRAI's guides and dictionary plus the federal and funder documents we index: Federal Register, Grants.gov, Regulations.gov and UKRI.

Works on this site and inside Claude, Cursor and the AI tools you already use.

Everything CASRAI publishes — this page, the dictionary, the guides and the news — stays open to read, with no account and no card.

Referenced across the research world

University of Cambridge logoColumbia University logoCrossref logoUniversity of Edinburgh logoHarvard University logoUniversity of Oxford logoPrinceton University logoStanford School of Medicine logoUniversity College London logoORCID logoUniversity of Cambridge logoColumbia University logoCrossref logoUniversity of Edinburgh logoHarvard University logoUniversity of Oxford logoPrinceton University logoStanford School of Medicine logoUniversity College London logoORCID logo
  • University of Cambridge logo
  • Columbia University logo
  • Crossref logo
  • University of Edinburgh logo
  • Harvard University logo
  • University of Oxford logo
  • Princeton University logo
  • Stanford School of Medicine logo
  • University College London logo
  • ORCID logo

View CASRAI adoption →